DAFFxEV57Z4 SplashZen For Dogs Instruction Manual

DAFFxEV57Z4 SplashZen For Dogs

Specifications:

• Splash guard (A) x 1
• Gray rectangular pieces with sticky pads (B) x 2
• Gray hook pieces x 2
• Suction cup strip pieces (D) x 3

Setting Up Your SplashZen:

1. Clean and dry the walls and edge of your tub.
2. Take the two gray rectangular pieces (B) and click them up into the back of the splash guard (A) spool, with the clear sticky pads facing out.
3. Take the clear stickers off the rectangular pads (B) to reveal the sticky edges.
4. Place the splash guard (A) spool on the edge of the tub with the sticky pads (B) aligned vertically and the handle facing the inside of the tub. Slowly slide the bottom of the guard along the top edge of the tub toward the wall until the sticky pads make contact with the wall.
5. Use your fingers to push the sticky pads against the wall to reinforce them and remove any bubbles. Wait at least 5 minutes to allow the sticky pads to adhere properly to the wall.
6. Have a partner slowly pull the splash guard (A) out of the spool and hold it in place for you.
7. Take the two gray hook pieces (C) and remove the clear stickers to reveal the sticky edges. Put the two gray hooks (C) through the top and bottom of the hook slots on the extended guard (A), with the hook openings facing inside the tub.
8. While still hooked on the extended guard, align the sticky pads (C) vertically and slowly slide the bottom of the guard along the top edge of the tub until the sticky pads make contact with the wall.
9. Remove the guard from the hooks and slowly roll it back into the spool on the other side.
10. Use your fingers to push the sticky pads (around the hooks) against the wall to reinforce them and remove any bubbles. Wait at least 5 minutes to allow the sticky pads to adhere properly to the wall.
11. To help guide where the suction cup strip (D) should be placed, slowly pull the splash guard (A) back out of the spool and hook it on the other side of the tub.
12. Take the pieces of the suction cup strip (D), get them wet, and press them down along the edge of the tub, along the bottom of the guard. They will go side by side to make a barrier along the entire bottom of the guard. The guard should be facing into the tub and the suction cup strips should be facing out.
13. If the final piece is too long, take a large pair of scissors and cut the strip off at the correct length. Discard any extra suction cup strip that you cut off.

Splash Guard Use:

Safety Warnings:

• For any additional questions, email us at: contact@splashzen.com or visit splashzen.com

FAQ

Q: Will SplashZen work with clawfoot or freestanding tubs?
A: No, SplashZen will not work with clawfoot or freestanding tubs as they require walls to attach to and a straight edge for the guard to run along.

Thank you for choosing SplashZen, the product that bath time fun without the mess
Carefully read and follow these instructions to set up and maintain your SplashZen. For more instructions, including a setup video, scan this QR code or visitsplashzen.com/pages/instructions
Note : SplashZen will not work with a clawfoot freestanding tub, as you need walls to attach to and a straight edge for the guard to run along

PARTS

SETTING UP YOUR SPLASHZEN

1. Clean and dry the walls and edge of your tub.
2. Take the two gray rectangular pieces (B)and click them up into the back of the splash guard (A) spool, with the clear sticky pads facing out.
3. Take the clear stickers off the rectangular pads (B) to reveal the sticky edges.
4. Place the splash guard (A) spool on the edge of the tub with the sticky pads (B)aligned vertically and the handle facing the inside of the tub. Slowly slide the bottom of the guard along the top edge of the tub toward the wall until the sticky pads make contact with the wall.
5. Use your fingers to push the sticky pads against the wall to reinforce them and remove any bubbles. Wait at least 5 minutes to allow the sticky pads to adhere properly to the wall.
6. Have a partner slowly pull the splash guard(A) out of the spool and hold it in place for you.
7. Take the two gray hook pieces (C) and remove the clear stickers to reveal the sticky edges. Put the two gray hooks (C)through the top and bottom of the hook slots on the extended guard (A), with the hook openings facing inside the tub
8. While still hooked on the extended guard, align the sticky pads (C) vertically and slowly slide the bottom of the guard along the top edge of the tub until the sticky pads make contact with the wall.
9. Remove the guard from the hooks and slowly roll it back into the spool on the other side.
10. Use your fingers to push the sticky pads(around the hooks) against the wall reinforce them and remove any bubbles. Wait at least 5 minutes to allow the sticky pads to adhere properly to the wall.
11. To help guide where the suction cup strip (D) should be placed, slowly pull the splash guard (A)back out of the spool and hook it on the other side of the tub.
12. Take the pieces of the suction cup strip(D), get them wet, and press them down along the edge of the tub, along the bottom of the guard.
13. They will go side by side to make a barrier along the entire bottom of the guard.
14. The guard should be facing into the tub and the suction cup strips should be facing out.
15. If the final piece is too long, take a large pair of scissors and cut the strip off at the correct length. Discard any extra suction cup strip that you cut off.

SPLASH GUARD USE

• During bath time, extend and hook it, with the guard resting just inside the suction cup strip.
• When taking kids in and out of the tub, or to store it, slowly roll the guard evenly into the spool.
• We recommend extending and hooking the guard to let it dry after use.
• If you want to hide or store the guard, make sure it’s dry and then pull up to release it fromthe gray rectangle pads. Re-attach it the same way.
• If you need to remove the suction cup strip, we recommend pulling it off sideways rather than straight up; this will help keep the suction cups from coming out.
• If you need to remove the sticky pads, do so carefully.
• If you need to order more sticky pads with rectangular pieces or hooks, we sell them affordably on splashzen.com

SAFETY WARNINGS

• To prevent serious injury or death, never leave children unattended while in the bathtub. The SplashZen splash guard is meant to be used under direct adult supervision.
• Do not use with children who are too young or unstable to keep their head safely above the water during bath activities and play.
• The splash guard material is flexible. If a child does slip or fall under the water, push the material down immediately and assist them.
• To keep children from slipping, we recommend putting an anti-slip material or bathmat on the bottom of the tub

Have comHave additional questions? Email us: contact@splashzen.com or visit splashzen.com

References

• SplashZen Bath Tub Splash Guard
• SplashZen Instructions

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>