SelectBlinds V&A Cordless Roller Shades with Cassette Instruction Manual

June 17, 2024
SelectBlinds

SelectBlinds V &A Cordless Roller Shades with Cassette Instruction Manual
SelectBlinds V&A Cordless Roller Shades with Cassette

Fitting the brackets

Inside Mount

Where the brackets are screwed into the lintel (or ‘ceiling’ of the recess)
Fitting the brackets

Outside Mount

Where the brackets are screwed onto a facing surface (a wall or window frame)
Fitting the brackets

Fitting the blind

Holding the shade at an angle, hook the lip at the front of the headrail over the front hook of the bracket. Then, pushing back against the front of the headrail, raise the back of the headrail and push upwards until it
snaps into place.
Fitting the blind

To remove the shade from the brackets, push back against the front of the headrail and twist the back of the headrail downwards until it disengages from the brackets.

Operation and spring tension

The shade’s spring mechanism is locked with a locking pin to prevent it unrolling during transit. Before you operate the shade for the first time, locate the locking pin and simply pull it out to remove it.

If you find that over time the spring mechanism is weakening (in that the shade does not easily retract when you raise it) then the tension can be increased very easily. Take the shade down from the brackets and locate the tension screw at one end. Using a screwdriver, turn the screw in the direction of the front of the shade. This will increase the tension in the spring and allow the shade to retract more easily. Make small adjustments (around 2 turns at a time) to avoid over-tensioning the spring mechanism.
Operation and spring tension

Attach clear handle(s) to the bottom rail by carefully sliding on.

Fitting the brackets

Inside Mount

Where the brackets are screwed into the lintel (or ‘ceiling’ of the recess)
Fitting the brackets

Outside Mount

Where the brackets are screwed onto a facing surface (a wall or window frame)
Fitting the brackets

Fitting the blind

Holding the shade at an angle, hook the lip at the front of the headrail over the front hook of the bracket. Then, pushing back against the front of the headrail, raise the back of the headrail and push upwards until it snaps into place.
Fitting the blind

To remove the shade from the brackets, push back against the front of the headrail and twist the back of the headrail downwards until it disengages from the brackets.

Operation and spring tension

The shade’s spring mechanism is locked with a locking pin to prevent it unrolling during transit. Before you operate the shade for the first time, locate the locking pin and simply pull it out to remove it.
Operation and spring tension

If you find that over time the spring mechanism is weakening (in that the shade does not easily retract when you raise it) then the tension can be increased very easily. Take the shade down from the brackets and locate the tension screw at one end. Using a screwdriver, turn the screw in the direction of the front of the blind. This will increase the tension in the spring and allow the blind to retract more easily. Make small adjustments (around 2 turns at a time) to avoid over-tensioning the spring mechanism.
Operation and spring tension

Attach clear handle(s) to the bottom rail by carefully sliding on.

Fitting the brackets

The brackets offer two methods of installation:

Inside mount

Use the front two holes in the top of the bracket to fix to the the ceiling of the recess

Outside mount

Use two screws through the back plate to mount onto a facing surface (a wall or window frame

Note that the position of the outermost brackets should be at least 5cm away from the ends of the rail, with any other brackets evenly distributed across the width.

Fitting the shade

Holding the rail at an angle, situate the T-shaped lip on the top of the cassette into the front lip of the bracket.
Fitting the shade

Twist the back of the cassette upwards until it snaps into place against the back lip of the bracket.

Child Safety

Chain Tensioner

Shades with clutch controls come with a continuous chain loop, which should always be screwed to the wall with the included chain tensioner.

The chain tensioner should be installed to a flat surface, so the bead chain is taut but not stretched. Be sure not to twist or cross the chain.

On inside mount shades, the tensioner may be attached to the windowsill or to the inside of the window frame. For outside mount or wall mount shades, the bracket may be mounted to the exterior of the window frame or the wall.

With a pencil, mark the desired location of the screw holes for the tensioner and then drill pilot holes. Then install the tensioner with the screws, making sure that the tensioner is fully installed, so that the spring is pushed inand the chain passes smoothly through the guide.
Child Safety

The chain tensioner forms an important safety function by keeping chain loops away from small children. Never operate this shade without a functioning and correctly installed chain tensioner.

Please retain these instructions for the future reference.

Thank you for purchasing this product. Please read the instructions and warning carefully before installation to ensure safe and satisfactory use of this product.

Before you begin

Before you begin

We will have positioned the controls where you requested during the ordering process. However if you decide to swap the side that they are on, direction of the roll or need to trim the blind further, the controls can be removed by simply unplugging them from the tube. This should be done prior to fixing the brackets.

Fitting the brackets

The brackets offer three methods of installation:

Inside-Mount

Where the brackets are screwed into the lintel (or ‘ceiling’ of the recess)

Outside-Mount

Where the brackets are screwed onto a facing surface (a wall or window frame)

Side-Mount

Where the brackets are screwed into the side walls of the recess

Top Tip

Inside mount or outside mount are recommended for most installations, whereas side-mount is only recommended if the width you gave us was taken right at the top of the recess.

Fitting the blind

Locate the depression end (the opposite end to the controls) of the blind into the cross-shaped hole in the corresponding bracket.
Fitting the blind

Lift the control end of the blind and slot the rectangular ‘lugs’ into the corresponding slots on the bracket.
Fitting the blind

Remove the No-Drill Blinds Headrail

The No-Drill Blinds Headrail will already be installed onto the existing product headrail.

Remove the product from the headrail (See Fig A), which will vary from product and depend on lift type.
Drill Blinds Headrail

Preparing the No Drill Blinds Headrail

Pull the lever from below or push down on the mechanism from above to retract the tension boot (See Fig B)
Drill Blinds Headrail

Install the metal strips or padded adhesive tape on opposite sides of the window opening where you’ll be installing the No-Drill Blinds Headrail. This is optional and only available on larger products.

Installing the No Drill Blinds Headrail

Insert the No-Drill Blinds Headrail into the window opening, make it flush with the top of the window opening, then push on the lever to extend the tension spring and secure the No-Drill Blinds Headrail. (See Fig C)
Drill Blinds Headrail

Installing the Product

Install the product onto the brackets (See Fig D). Test and operate the product to ensure secure installation and smooth functionality.
Drill Blinds Headrail

Uninstalling the No Drill Blinds Headrail

To uninstall the product, follow step 1 by removing the product from the headrail and use a screwdriver to unlatch the lever.

Make sure to hold the No Drill Blinds Headrail in place while unlatching the lever. This will prevent damage to the window or headrail.

Tech Tip

If the fixed boot end was accidentally forced out, use a flathead screwdriver to twist the red “droplets” towards the center and then push it back in.

Company Logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

SelectBlinds User Manuals

Related Manuals