ER KANG JT-H10 2000LBS Strength Training Power Cage Instruction Manual
- June 17, 2024
- ER KANG
Table of Contents
ASSEMBLY INSTRUCTIONS
JT-H10
JT-H10 2000LBS Strength Training Power Cage
ER KANG RECOMMENDS TWO PEOPLE NEEDED TO ASSEMBLE THIS CAGE IN FLAT
GROUND NOTE: DO NOT FULLY TIGHTEN HARDWARE UNTIL FINAL STEP
MEET ANY QUESTION ASSEMBLING OR PRODUCT?
EMAL US FOR CUSTOMER SERVICE
[email protected]
Read all precautions and instructions in this manual before using this
equipment
ASSEMBLY
Make Things Easier for Yourself
Everything in this manual is designed to ensure that the weight system can be
assembled suc-cessfully by anyone.However, it is important to realize that the
versatile weight system has many parts and that the assembly process will take
time. Most people find that by setting aside plenty of time, assembly will go
smoothly.
Before beginning assembly, carefully read the following information and
instructions:
- Assembly requires two people.
- Place all parts in a cleared area and remove the packing materials. Do not dispose of the packing materials until assembly is completed.
- Tighten all parts as you assemble them, unless instructed to do otherwise.
- As you assemble the weight system, make sure all parts are oriented as shown in the drawings.
- For help identifying small parts, refer to the PART IDENTIFICATION CHART on page 5.
The following tools (not included) are required for assembly:
- Two adjustable wrenches
- One rubber mallet
- One standard screwdriver
- One Phillips screwdriver
- Lubricant,such as grease or petroleum jelly,and soapy water.
Assembly will be more convenient if you have asocket set, a set of open-end or closed-endwrenches, or a set of ratchet wrenches.
PARTS LIST
PARTS LIST
NUMBER| DESCRIPTION| QUANTITY
1| Left Side Base| 1
2| Right Side Base| 1
3| Triangle Connecting Pieces| 8
4| Rear Base| 1
14| BOLT M1045| 4
18| Foldable Pedal| 1
19| Weight Storage Rack Base| 2
20| Weight Storage Frame| 2
21| Landmine Attachment| 1
27| Band Peg| 4
34| BOLT M1095| 12
38| BOLT M10*20| 6
42| M10 NUT| 16
44| Φ10 WASHER| 34
46| BIG WASHERS| 4
52| Pull Ring Pins| 5
54| 2″ Weight Clips| 4
58| 90mm Pulley| 4
Part No.28 need to be mounted in
advance on the two front upright column.
PARTS LIST
NUMBER| DESCRIPTION| QUANTITY
5| Rear Upright Column| 2
7| Front Upright Column| 2
28| Cable Silding Sleeve| 2
31| Silding Sleeve Pulley Sets| 2
34| BOLT M1095| 8
40| BOLT M12105| 2
42| M10 NUT| 8
43| M12 NUT| 2
44| Φ10 WASHER| 16
45| Φ12 WASHER| 4
PARTS LIST
NUMBER| DESCRIPTION| QUANTITY
8| Right Height Select Plate| 1
13| Smith Guide Rod| 2
14| Smith Bar Safety Catch| 2
15| Smith Bar Sliding Sleeve| 2
16| Smith Bar| 1
22| Dip Bar Left| 1
23| Dip Bar Right| 1
29| J Hook Left| 1
30| J Hook Right| 1
33| Left Height Select Plate| 1
35| BOLT M1090| 8
38| BOLT M1020| 4
42| M10 NUT| 12
44| Φ10 WASHER| 16
47| Washer (026*043)| 2
54| TWeight Clips| 2
55| Shock Absorption Pads| 4
56| Shock Absorption Spring| 2
PARTS LIST
NUMBER| DESCRIPTION| QUANTITY
6| Upper Side Cross Column| 2
17| Pull-up Bar| 1
24| Safety Bar Left| 1
25| Safety Bar Right| 1
26| Foam Roller Attachment| 1
27| Band Peg| 2
35| Bolt (M1090)| 4
36| Bolt (M1070)| 8
37| Bolt (M10*65)| 2
42| M10 NUT| 16
44| Φ10 WASHER| 30
52| Pull Ring Pins| 2
57| Short Pull Ring Pins| 1
58| 90mm Pulley| 4
59| Shaft Sleeve| 8
When you install the guide rod
on the back side, make sure that all the other parts on the guide rod are
installed and finally secure the top two screws
PARTS LIST
NUMBER| DESCRIPTION| QUANTITY
9| Rear Upper Connecting Column| 1
10| Guide Rod| 2
11| Weight Holder Frame| 1
12| Connecting Pieces| 2
34| Bolt (M1095)| 4
35| Bolt (M1090)| 4
39| Bolt (M1045)| 1
41| Bolt (M825)| 2
42| M10 NUT| 9
44| Φ10 WASHER| 18
47| Washer (1)26*(143)| 2
53| 1″Weight Clips| 2
54| TWeight Clips| 2
55| Shock Absorption Pads| 2
56| Shock Absorption Spring| 2
58| 90mm Pulley| 4
59| Shaft Sleeve| 8
PARTS LIST
NUMBER| DESCRIPTION| QUANTITY
32| Moving Pulley| 2
60| Cilps| 2
61| Cable A 13.12m or 516.5″| 1
63| Cable Handles| 1
PARTS LIST
NUMBER| DESCRIPTION| QUANTITY
38| BOLT M10*20| 4
42| M10 NUT| 4
44| ϕ10 WASHER| 8