MW-100 AWOL Matte White Fixed Frame Projector Instruction Manual

: June 17, 2024
: AWOL

Table of Contents

PACKING LIST
Precautions
Assemble the frame
Assemble the screen
Assemble screen and inner frame
Outer frame installation
Mount on the wall
Specification
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

AWOL Vision Matte white
Fixed Frame Screen
INSTRUCTION MANUAL

MW 100 AWOL Matte White Fixed Frame Projector - Cover

Thank you for chossing the AWOL Vision Matte White Projection Screen. Please read this manual carefully before installtion and use.

PACKING LIST

MW 100 AWOL Matte White Fixed Frame Projector - PACKING LIST
1

MW 100 AWOL Matte White Fixed Frame Projector - PACKING LIST
2

Precautions

To ensure the projection performance of this product, please pay attention to the following operating requirements.

When assembling, ﬁnd a suitable size ﬂoor or table. The surface must be clean and free of any obstacles.
The ﬂoor or table must be covered with clean materials such as cloth, ﬁlm, blankets, etc.
Handle with care during installation to prevent personal injury or property damage.
Do not touch the surface of the projection screen with unglved hands.
Do not touch the projection surface with sharp or hard objects to prevent damage to the screen material.
Keep children away from the screen to prevent accidents.
The surface of the screen must be cleaned and treated regularly, and it is recommended to take care of it once every two weeks.
Please use a soft cotton cloth to wipe (dip some water) gently, and it is not advisable to use any chemical cleaners or alcohol.

Assemble the frame

Open the package and check whether the accessories in the box are complete.
Connect inner frame A and inner frame B ﬁrst (Figure 1)
Insert the 4 corner connectors into the inner frame C (picture 2)
Assemble the four inner frames and struts as shown in the ﬁgure below, and lock them with screws after the inner frame is assembled (Figure 2, Figure 3);

MW 100 AWOL Matte White Fixed Frame Projector - Assemble the frame
1

MW 100 AWOL Matte White Fixed Frame Projector - Assemble the frame
2

Assemble the screen

Wear gloves (to avoid the screen being stained with ﬁngerprints that can not be erased). Lay a clean cloth on a ﬂat, clean surface (or ground) to protect the screen.
Take out the screen from the package, turn the screen face down, unfold the screen, and then according to the length of the glass ﬁber strips, take the glass ﬁber strips insert to around of screen as shown below.

MW 100 AWOL Matte White Fixed Frame Projector - Assemble the screen
1

MW 100 AWOL Matte White Fixed Frame Projector - Assemble the screen
2

Important note: Please cooperate with two people when assembling, and do not make any actions that may cause the screen to fold or rub against hard objects.

Assemble screen and inner frame

Put the assembled frame on the screen. Align the frame with the line marks on the four corners of the screen (Figure 6)
Adjust the position of the screen and the frame so that the frame is in the middle of the screen, and check the overall ﬂatness of the screen. before installing the tension spring.
Hang the screen on the frame with the tension spring. Please follow the following sequence for hooking tension springs, Firstly install the four corner springs in the order of 1~8; then hang the middle springs 9~12, and ﬁnally spring from the middle, and install the other springs symmetrically in turn (Figure 7)

Outer frame installation

Splice the outer frame A and outer frame B into a complete frame (Figure 8), and drive the hexagonal studs into the long frame splicing strip (Figure 9)
Put the outer frame against the frame screen, align the four corners, connect the surroundings with corner connector and lock all the screws (Figure 10)
Use screws to lock the joints of the outer frame on the hexagonal studs, and clip the corner protectors into the slots of the outer frame (Figure 11)

Mount on the wall

Install wall hangers on the wall according to screen size. Required tools: level, hammer drill, pencil, ladder, etc. As shown below. Please estimate the installation position of the screen before installing the wall pendants. The height of the lower edge of the screen from the ground is generally about 50~80cm.
Drill holes on the marks on the wall with a percussion drill, insert the rubber plug, screw on the screws, and ﬁx the wall bracket (Figure 13)
Hang the assembled screen on the wall (operated by two persons) (Figure 14)