KENTON ROLAND JUPITER 4 Midi Retrofit Kits Instructions

June 17, 2024
KENTON

KENTON ROLAND JUPITER 4 Midi Retrofit Kits

KENTON-ROLAND-JUPITER-4-Midi-Retrofit-Kits-PRODUCT

Product Information

Specifications:

  • Product: Kenton MIDI Retrofit for Roland Jupiter 4
  • Compatible with Jupiter 4 MIDI retrofit kits produced after 1st December 2005 Firmware JUP45100 or later

Product Usage Instructions

Using the MIDI Interface

The Kenton MIDI retrofit for Roland Jupiter 4 allows for enhanced MIDI functionality. The red push button on the interface enables different modes during normal playing mode. It is important to ensure that no keys are pressed on the remote MIDI keyboard before pressing the red button to avoid unpredictable results.

Setting Transpose and Arpeggio Divide:

The bottom four octaves on a 61-note remote keyboard are used to set transpose, while the top octave is used to set the arpeggio divide. Press the following keys on the remote MIDI keyboard:

  • G = Set triplet on
  • Ab = Clock divided by 8 (eighth speed)
  • A = Clock divided by 4 (quarter speed)
  • Bb = Clock divided by 2 (half speed)
  • B = Clock normal – no divide (full speed)
  • TOP C = ENTER = Return to normal playing and store new setting

Function of Keys During Set-Up Mode:

Different keys on the remote MIDI keyboard correspond to specific functions during set-up mode, such as setting the receive channel, selecting controller sources, and assigning MIDI control sources to destinations.

Assigning MIDI Control Sources to Destinations:

Various MIDI control sources can be assigned to different destinations, allowing for customization of the MIDI functionality. Each source has a default destination, but sources can have multiple destinations as needed.

Frequently Asked Questions

How do I reset the MIDI settings to default?

To reset the MIDI settings to default at any time, switch the synth on while holding the red push button pressed. Hold the button for a couple of seconds and then release it.

User instructions for Kenton MIDI retrofit for ROLAND JUPITER 4
These instructions are only for Jupiter 4 MIDI retrofit kits produced after 1st December 2005 Firmware JUP45100 or later
N.B. Different instructions apply to earlier Kenton Jupiter 4 MIDI retrofit kits.

USING THE MIDI INTERFACE

  • When you turn on the synthesizer for the first time, you will be in omni-off mode channel 1 for receive – See the following pages for other factory default settings. When you select a receive channel, this will be stored in memory and will be remembered for when you subsequently turn on the synth – all parameters listed on the next page are stored. If you want to put the machine back to the factory default settings at any time, switch the synth on whilst holding the red push button pressed – hold for a couple of seconds then release.
  • The MIDI switch on the front panel of the Jupiter-4 (next to the tuning knob) is used to enable the MIDI control of pitchbend & mod wheel. Set the MIDI switch to ON (down) and use the bend sensitivity knob (bender panel) to set the range for MIDI pitchbend. Set the VCO / VCF / VCA switches (bender panel) to LFO to select what the MIDI Mod Wheel controls, in conjunction with the LFO modulation knob (bender panel). Usual setting is only VCO switch to LFO (bend setting does nothing). MIDI will always play the notes of the Jupiter-4 regardless of the setting of the MIDI switch.

RED PUSH BUTTON

Two modes are available by pushing the red push button during normal playing mode. Before you press the red button however, make sure that no keys are pressed on the remote MIDI keyboard otherwise the results may be unpredictable. The key presses detailed below must be entered on the remote MIDI keyboard only

  1. SET-UP MODE
    For setting MIDI channels and assignments. Give the red push button two short presses (half a second each) -then release. Follow this with a key or sequence of keys as detailed on page 2. After making a MIDI channel assignment, you will be automatically returned to playing mode but after making other assignments you will need to press the ENTER key (Top C) to return to playing mode. This is to enable you to make the multiple key presses required when re- assigning Sources to Destinations. (N.B. all set-ups are stored in non volatile memory).

  2. TRANSPOSE MODE / ARPEGGIO CLOCK DIVIDE SETTING MODE
    Press and hold the red push button for about four seconds – then release. Middle C will sound on the synth and continue to sound until you press a key. The key that you press on the remote keyboard will be the new middle C for MIDI IN. You can set any value up to two octaves up or down – settings outside this range will be ignored (where middle C = no transposition) . Note that transpose mode cannot be entered from set-up mode. (N.B. the transposition will be stored in non volatile memory).

The bottom four octaves on a 61 note remote keyboard are used to set “transpose” but the top octave will set the arpeggio divide.

  • G = Set triplet on (can be used with any of below) Ab = Clock divided by 8 (eighth speed)
  • A = Clock divided by 4 (quarter speed)
  • Bb = Clock divided by 2 (half speed)
  • B = Clock normal – no divide (full speed)
  • TOP C = ENTER = Return to normal playing and store new setting

For more information on the operation of the arpeggio clock with MIDI, see note #11 further on.

Function of keys during set-up mode

KENTON-ROLAND-JUPITER-4-Midi-Retrofit-Kits-FIG-1

ASSIGNING MIDI CONTROL SOURCES TO DESTINATIONS

SOURCE
Pitch-bend wheel Modulation wheel (cc#1) Aftertouch Velocity
Controller X (def cc#16) Controller Y (def cc#17) MIDI Volume (cc#7)

DEFAULT DESTINATION
Pitch-bend
Modulation Modulation
VCF / Filter cutoff
VCA / Volume

  1. To assign sources to destinations,

    • a) press the red push button twice to enter set-up mode
    • b) select a source by using one of the keys A to Eb (see table on previous page)
    • c) [optionally if the source is Controller X or Y, you can assign a controller to it now – see below]
    • d) select destinations OFF to de-select previous assignments for this source
    • e) select destinations ON to make new assignments for this source
    • f) either hit Top C to enter/exit, or select a new source and make assignments for that [go back to b]
  2. Controllers X & Y can be assigned to any continuous controller (cc). By default controller X is assigned to cc#16, and controller Y is assigned to cc#17. To re-assign either of them, first press the red push button twice to enter SET-UP mode. Next press the Db or D key (see table on previous page) to select the X or Y controller source, then send a MIDI message of the required continuous controller. Then either press top C to enter / exit, or use some of the destination keys to assign what this controller will control.
    For example to set controller Y to respond to cc#4, press the red button twice, press D, send a cc#4 message to the Jupiter from another synth or MIDI controller, then press top C to enter /exit. [or select another function]

  3. Sources can have multiple destinations, so for example controller X could be assigned to control both filter and volume at the same time, should you want it to.

  4. Where pitch-bend wheel is the source, only the bend wheel UP will affect destinations other than pitch-bend. Also where pitch-bend is the destination, sources other than pitch-bend wheel will only bend the pitch UP.

  5. Receive channel setting will return you directly to playing mode, all other keys will let you stay in SET-UP mode until you press the ENTER key (Top C).

  6. The ENTER key (Top C) also performs a “reset all controllers” function – OFF in most cases, but ON for volume, and centre for pitch bender.

  7. If you want to put the MIDI back to the default settings at any time, switch the synth on whilst holding the red push button pressed – hold for a couple of seconds then release.

  8. During set-up mode, the retrofit will receive on ALL MIDI channels.

  9. List of continuous controllers (cc) recognised – (numbers in decimal)

    • 01 modulation wheel
    • 07 Main volume
    • 64 sustain pedal
    • 121 reset all controllers
    • 124 omni mode off (always poly)
    • 126 (mono mode) = all notes off
    • 123 all notes off
    • 125 omni mode on (always poly)
    • 127 (poly mode) = all notes off
      nnn Controller X (user defined where nnn = any controller) (default = cc#16) nnn Controller Y (user defined where nnn = any controller) (default = cc#17)
  10. List of other commands recognised – (numbers in hexadecimal)

  11. 8nH notes off

  12. BnH continuous controller (see above)

  13. DnH channel pressure (aftertouch)

  14. FEH active sensing

  15. 9nH notes on & velocity

  16. EnH pitch-bend change

  17. Using arpeggio clock. With the rear panel toggle switch in the down position, and the Jupiter 4’s arpeggio switch set to INT the clock will function as normal. The only time you need to change the setting of the rear panel switch is if you want to use the Jupiter’s external jack input, when putting the switch in the up position selects external socket.
    To select MIDI clock merely set the Jupiter’s arpeggio switch to EXT (with the rear panel switch in the down position) and the clock will take its tempo from MIDI. Note that if the switch is set to MIDI and there is no MIDI clock present, the JUPITER 4 will not play if it is in arpeggio mode.
    To change the divide rate, press the push button and hold in for about four seconds, until a note sounds, (this is transpose mode) the bottom four octaves are used to set “transpose” but the top octave will set the arpeggio divide.

TOP C = ENTER – Return to normal playing and store

  • B = Clock normal – no divide (full speed)
  • Bb = Clock divided by 2 (half speed)
  • A = Clock divided by 4 (quarter speed)
  • Ab = Clock divided by 8 (eighth speed)
  • G = Set triplet on (can be used with any of above)

You will need to press TOP C (Enter) after any selection.
If you want to use Triplet, you will need to set this after the divide ratio, as pressing any of the divide ratios cancels Triplet.

GENERAL INFORMATION ABOUT MIDI CONNECTIONS

Any MIDI IN should be connected to a MIDI OUT or a MIDI THRU similarly any MIDI OUT should be connected only to a MIDI IN and any MIDI THRU should also only be connected to a MIDI IN.
MIDI OUT (if fitted) is the signal from the synthesizer (or drum machine etc.) that is to be sent to another instrument. MIDI IN is a received signal that contains MIDI information from another synth, and MIDI THRU is an exact copy of information arriving at the MIDI IN socket. This allows several instruments to be connected together.

If you want to wire your own MIDI cables the following information may be useful.

  1. Although a 5 pin connector is used, only two connections plus an earth connection are required.
  2. If you look at the din plug from the wiring side you will see that the pins are numbered. From left to right (or clockwise) these are 1 – 4 – 2 – 5 – 3.
  3. The pins numbered 1 & 3 are not used.
  4. The screen (earth) is connected to pin 2 (centre pin)
  5. Pin 4 of one plug should be connected to pin 4 of the other
  6. Pin 5 of one plug should be connected to pin 5 of the other
  7. You should now have a working MIDI lead
  8. It is preferable to label one end of the cable MIDI IN & the other end MIDI OUT, to avoid confusion.

WARRANTY

All Kenton MIDI Kits come with a 12 month (from purchase date) back to base warranty, (i.e. customer must arrange and pay for carriage to and from Kenton Electronics).

Unit 3, Epsom Downs Metro Centre, Waterfield, Tadworth, KT20 5LR, UK Tel: +44 (0)20 8544 9200 Fax: +44 (0)20 8544 9300
www.kenton.co.uk

Copyright (c) KENTON Electronics & John Price 1986-2023

version JUP45001

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals