FVC SP5021B Sprinter Van 48 Upper Cabinet Installation Guide

TOOLS REQUIRED

ADWAG INSTAL

• PHILLIPS SCREWDRIVER
• 3/8” WRENCH
• 5/8” WRENCH
• TAPE MEASURE
• 1/8” ALLEN WRENCH

DIY INSTALL

• PHILLIPS SCREWDRIVER
• RIVET NUT TOOL
• POWER DRILL
• IMAPCT DRIVER
• MARKER

INSTALL INFO

TIME TO INSTALL THIS PRODUCT : 1 HOUR Additional help is suggested for a few of the install steps

BEFORE YOU START

Please inspect the product and packaging upon delivery to ensure there are no issues and that all parts and hardware are accounted for.

Contact us ASAP if anything is missing at support@flatlinevanco.com

BEFORE YOU START

PACKAGE CONTENTS

• CABINET SHELL
  

• CABINET DOOR

• LATCH BRACKET

• ADWAG MOUNTING BRACKET
  
  WITH OPTIONAL ADWAG MOUNTING KIT:

HARDWARE

• CABINET LATCH

• 6-32 X 0.375 ROUND HEAD PHILLIPS DRIVE SCREW

• 6 X 0.4375 ROUND HEAD PHILLIPS DRIVE SCREW

• M5-0.8 X 16 ROUND HEAD PHILLIPS DRIVE SCREW

WITH OPTIONAL ADWAG MOUNTING KIT:

• L-TRACK STUD

• 10-32 X 0.6875 FLAT HEAD HEX DRIVE

• 10 SCREW FLAT WASHER

• 10-32 NYLON INSERT LOCKNUT

INSTALLATION

STEP | 01 LAYOUT & INSTALL PREP

Determining where you’d like to install your cabinet is up to you, however there are some tips that make choosing the location a little easier.

See the diagrams FIG 1 and FIG 2. Notice the centerline ribs depicted as a dotted line. This centerline is standard across all sizes of Sprinter Van and can be used as a reference point when measuring your available wall space.

Take the time to measure your available wall space and layout potential cabinet locations before installing.

NOTE – Due to the amount of variability and specific c needs of each vehicle, we do not supply hardware for DIY installs. See page 7 for more info.

NOTE – Mounting hardware is included if you purchased the optional Adwa Mounting Kit.

NOTE – Doors come boxed and shipped separately.
NOTE – Install the cabinet shell to the van body before adding doors.

• This will make the cabinet be lighter and easier to lift.
• Door alignment will change slightly once cabinet is tightened to the van.

STEP | 02 ADWAG INSTALL

[SKIP TO PAGE 7 FOR DIY INSTALL]

2.1a Determine where you’d like to install your cabinet and insert (2ea) L-Track Studs into the rails along the wall and the ceiling.

NOTE -The distance between the mounting points are 36” on the upper section and 14” – 16” on the lower.

2.2a Install the Mounting Brackets to the Cabinet using (2ea) 10-32 X 0.6875 Flat Head Hex Drive Screws, #10 Flat Washers and 10-32 Nylon Insert Locknuts.

2.3a With help, lift the Cabinet up onto the L-Track Studs and fasten it together with the L-Track Stud Nuts.

STEP | 02 DIY INSTALL

The upper and lower mounting surfaces of the Cabinet have multiple horizontal slots to accept hardware for wherever and however you’d like to install them.

The slots can accept 1/4” hardware (i.e. 1/4-20 or #12) for your reference.

It is recommended to install cabinets securely into the vans structural sheet metal using rivet nuts and screws for maximum performance. Sheet metal screws can also be used in some situations.

In FIG 6, note the areas marked in orange. Any spot along this structural sheet metal can be used to mount your cabinet.

2.1b With help, lift the cabinet to the desired location in the van. Identify which mounting slots will be used for the ceiling and wall mounting hardware.

2.2b Mark locations if necessary.

2.3b Mount cabinet with desired hardware.

NOTE – Removing or drilling through existing wall panels may be necessary.

PRO-TIP: Bracing the gaps between these mounting areas with wood or metal fi ring will provide more surface area for mounting your cabinet to the van.

STEP | 03 DOOR ASSEMBLY

STEP | 04 DOOR INSTALL

4.1 After mounting the Cabinet in the van and installing the Latch to the door, carefully pull on the Cabinet Hinges into the open position as shown in FIG 9.

4.2 Mount the Door to the Hinges with (2ea) 6-32 Machine Screws in the hinge slots as pictured in FIG 10.

NOTE – Be sure to use the Machine Screws and not the Wood Screws, as that would prohibit your ability to adjust the alignment of the doors.

STEP | 05 ALIGNMENT

5.1 Close the door and verify alignment. Adjust as needed by loosening screws and re-positioning door(s). Repeat as necessary.

5.2 Once alignment is achieved, add (2ea) #6 Wood Screws into the setting hinge slots as pictured in FIG 11.

5.3 Tune the Cabinet Latch by turning the adjustment screw to a length that provides a snug compression to the cabinet body when closed. Lock in the adjustment by tightening the Jam Nut down against the latch arm.

GET OUT AND EXPLORE!

• LEAVE US A REVIEW
  Happy with your new FVC product? We would love to hear (and see) from you! Head to the product page and click “Leave Review.” Add a short review and upload a few photos to be showcased on the product page.

• SHARE YOUR PICS
  We love seeing how our customers use their FVC products and following along with your adventures. Tag us in your photos with: @flatlinevanco or send them to us via email. We love posting customer pictures in our feed!

• NEED ANY HELP?
  If you are having any issues with your product, please reach out, and we will make it right. FVC is a company of van and outdoor enthusiasts that design and use our own products, so we want you to be as stoked on your new parts as we are!

FL ATLINE VAN CO • SUPPORT@FLATLINEVANCO.COM • 888-667-5576 011

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>