Clean Air Kits DAFYEJ9wH5c Aerating End Table Kit Instructions
- June 17, 2024
- Clean Air Kits
Table of Contents
Clean Air Kits DAFYEJ9wH5c Aerating End Table Kit
Specifications
- DC barrel adapter
- 3 & 4-Way Splitters
- 12V DC Power-supply
- Seven 120mm Fans
- Two 21×8.5 Fan Panels
- Two 24×8.5 Bridge Panels
- Tension Cord
- Zip Ties
- 7 Fan Grills
- 3M Filtrete MPR 1900 / 2200 20×24 (Sold Separately)
- 28 Push Pins
- Scissors
- Pliers
- Putty Knife & Screwdriver
- 16 Screws
- Strain relief grommet
Product Usage Instructions
Fan Grill Attachment:
Arrange fan grills in a consistent or alternating orientation. Finish
attaching with push pins until all grills are attached. Leave the panel grill-
side down on the table for the next step.
Fan Frame Installation:
Orient fans with the pretty side up (specs facing grills) and wires exiting
a consistent side. Firmly push fan frames onto push pins. Inspect from the
side to ensure fans contact panels uniformly.
Panel Assembly:
Screw together the side fan panels and black bridge panels to create the
structure of the end table kit.
Bungee Installation:
Hook or tie the bungee between opposite sides using the back screw holes of
the middle fan. Tension slightly so panels bow inward a bit.
Cable Connection:
Connect 3 & 4-way splitters to fan cables on each side. Connect splitters
to the dual 4-pin adapter from the grommet hole.
Cable Management:
Secure loose cables away from fans by zip-tying them to the bungee to
prevent obstructions.
Power Connection and Testing:
Connect the DC barrel plug to the AC adapter and plug it into AC for
testing. Ensure all 6 fans run smoothly without any wire obstructions.
Final Setup:
Disconnect the power, apply foam tape to the inside edges, and gently push
the filters in, sliding a putty or butter knife between foam and filter to pry
back any edges that catch. Place fan & filter sides at least 2, preferably 12
inches from walls for optimal performance.
Frequently Asked Questions (FAQ)
-
Q: Can I use different filters with this kit?
A: The kit is designed for use with 3M Filtrete MPR 1900 / 2200 20×24 filters. The use of other filters may affect performance and compatibility. -
Q: How do I ensure proper airflow with the end table kit?
A: It is recommended to place the fan & filter sides at least 2, preferably 12 inches from the walls for good performance to ensure proper airflow and ventilation. -
Q: What should I do if not all fans are running during testing?
A: Check the cable connections, ensure there are no obstructions, and verify power supply connections. If issues persist, contact customer support for assistance.
Assembly videos: https://www.youtube.com/@cleanairkits
ELECTRICAL
COMPONENTS
HARDWARE
MATERIALS
INSTRUCTIONS
-
Arrange fan grills in a consistent or alternating orientation. Finish attaching with push pins until all grills are attached.
Leave the panel grill-side down on the table for pushing in step 2) -
Orient fans with pretty side up (specs facing grills) and wires exiting a consistent side. Firmly push fan frames onto push pins. Inspect from the side to ensure fans contact panels uniformly.
-
Screw together the side fan panels and black bridge panels.
-
Hook or tie the bungee between opposite sides using the back screw holes of the middle fan. Tension slightly so panels bow inward a bit.
-
Connect 3 & 4-way splitters to fan cables on each side. Connect splitters to dual 4-pin adapter from grommet hole.
-
Secure loose cables away from fans by zip-tying to bungee.
-
Connect the DC barrel plug to the AC adapter and plug it into the AC for the test. All 6 fans should run without any wire obstructions.
-
Disconnect power. Apply foam tape to the inside edges. Push the filters in gently, sliding a putty or butter knife between the foam and filter to pry back any edges that catch.
FINAL INSPECTION
You are responsible for finding noticeable gaps/leaks (e.g. > 2 square mm)
around fans or filters that can reduce filtration efficiency. Inspect
carefully from all sides. Tighten push pins, panel connectors, bungees, or
plug with foam or tape as necessary.
Place fan & filter sides at least 2″, preferably 12 inches from walls for good performance! Thanks for your purchase!
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>