IKEA T4 Petkit Pura Max Self Cleaning Cat Litter Box User Manual
- June 17, 2024
- Ikea
Table of Contents
IKEA T4 Petkit Pura Max Self Cleaning Cat Litter Box
USER MANUAL
PETKIT PURA MAX SELF-CLEANING CAT LITTER BOX
PRODUCT LIST
*Please ensure that all accessories are present before installation and use.
Accessories
PRODUCT DESCRIPTION
*Note: In order to provide the best experience possible, we periodically update our products with various improvements. The actual product may vary from its illustrations on packaging. For any inconsistencies, please refer to the actual product.
PRODUCT INSTALLATION
Installing Waste Container
-
Open the latch to the right and pull out the waste container; open its lid to take out accessories.
-
Spread the trash bag evenly and press it into the bottom of the waste container, and close the lid of the container.
*Note: The trash bag need to be fastened by the two sides of the lid (as shown in Fig. 1). -
Take out the Odor Eliminator NSO and put it into the groove and press the silicone lid to firmly closed.
-
Re-install the waste container to the main unit and close the latch.
-
Take out the power adapter, insert it into the power port on the back of the main unit, and then plug in.
Pouring Cat Litter
Ensure that the amount of cat litter does not exceed the MAX line. The length of the cat litter selected must be shorter than 1.2cm, and the diameter less than 3mm.
HOW TO USE
Operating Main Unit
Button usage
Function Description
Display Indication
Status Indication
Fault Indication
App Binding and Activating
-
Download and install the App:
-
Add the device
Open the downloaded “PETKIT” App and navigate to the home page; Tap the”+” button in the top right corner to add the device. Select “PETKIT PURA MAX SELF-CLEANING CAT LITTER BOX”. Note: To enhance user experience, occasional software upgrades may occur so that the app interface may vary. Please refer to the actual product. -
Start connection
Tap the Menu button on the device and switch to “Configure network”. Tap the OK button to initiate connection. The screen will display “Connecting … “, and the App will start connecting to the device. Please wait until the configuration is successful. -
Note: To enhance user experience, occasional software upgrades may occur so that the app interface may vary. Please refer to the actual product.
-
Read usage guide
To ensure the safety of your pet and the correct usage of this product, please read the usage guide carefully to use the product properly after successfully connecting it to the App for the first time.
Note: To enhance user experience, occasional software upgrades may occur so that the app interface may vary. Please refer to the actual product.
Smart Control via App
-
Viewing device status
Click “PETKIT PURA MAX” on the device list on the home page to enter the device’s home page and take a look at its working status, toileting times of the day as well as remaining cat litter. Note: To enhance user experience, occasional software upgrades may occur so that the app interface may vary. Please refer to the actual product. -
Basic function description
-
Clean now: Click it to clean the litter box after your fur baby finishes toileting.
-
Maintenance mode: Click it to enter the maintenance mode to leave the cylinder opening facing up and staying still to clean the device and add cat litter with ease.
-
Empty cat litter : Click it to empty the remaining cat litter in the cylinder after installing the cat litter remover.
-
Smart settings: Safety and cleaning functions can be set.
-
Odor removal now : Click it to deodorize.
-
Light: Click it to turn on the light to check the conditions of your fur baby or the inside of the cylinder.
-
- PETKIT AIR PURIFIER SMART SPRAY needs to be purchased separately.
Using Odor Removal Device
Click “Bind Smart Spray” on the home page, or click “SUPER ODOR REMOVAL” in
settings to bind PETKIT AIR PURIFIER SMART SPRAY (optional choice).
- Odor removal: Odor removal is automatically performed after your fur baby toilets to keep air fresh.
- Light: Light is turned on via app to check the conditions of your fur baby or the inside of the cylinder.
Note: To enhance user experience, occasional software upgrades may occur so that the app interface may vary. Please refer to the actual product.
Other Functions’ Description
-
Kitten mode:
This mode needs to be turned on if you have kittens or pregnant cats at home. When this mode is on, the device will not clean itself periodically or automatically. Waste is collected by clicking “Clean now”. -
Rotation without interruption
-
When this function is off, the device will stop working if it senses any cat is approaching. When the opening of the cylinder is facing down, other cats may enter the litter box, resulting in their secretions leaking into the bottom of the device, which makes it harder to clean.
-
*When this function is on, the device will not stop working if it senses any cat is approaching, which may reduce the possibility of cat entering and its secretions leaking into the bottom of the device.
Note: To enhance user experience, occasional software upgrades may occur so that the app interface may vary. Please refer to the actual product.
CLEANING AND MAINTENANCE
For your cats’ health, the cylinder needs regular disassembly to clean.
Emptying Cat Litter
Before cleaning, please empty the remaining cat litter in the cylinder.
- Press the fasteners of the cat litter remover into corresponding holes of the litter sifter. Upon hearing “Click”, the installation is done.
- Tap “Empty cat litter” on the home page of the device to empty remaining cat litter.
- When emptying the remaining litter is done, pinch A (as shown in the figure) to pull down the remover.
Disassembling Cylinder
- Lift upward to remove the side cover. *Note: Please be sure to turn off or plug off the device before removing the cylinder.
- Disassemble lock components
- Lift upward to take down the cylinder
Disassembling Litter Sifter
-
Open the side cover and grasp the litter sifter (as shown in Fig. 1) .
*Note: Please be sure to turn off or plug off the device before removing the cylinder. -
Press it inward (as shown in Fig.2) .
-
Make the sifter slightly bent and pull it out when it is off the buckle.
Cleaning Main Unit
- Wash the cylinder and litter sifter, which is suggested to add moderate amounts of detergent and rinse them thoroughly.
- Use a wet towel to wipe the surface and interior of the main unit, ensuring the sensor remains clean.
*Note: After cleaning, all parts should be reassembled only when they are completely dry. The main unit should only be wiped clean. It is prohibited to rinse or immerse it in water or it may be damaged!
Installing Litter Sifter
- Secure the front side of the litter sifter into point a.
- Grasp the litter sifter and press it inward until it is slightly bent.
- Secure the other side of the litter sifter into point b.
- If the litter screen is able to be shaken back and forth, the installation is complete.
Installing Cylinder
- Re-install the cylinder
- Secure the buckles of the cylinder and make sure they are firmly fastened.
- Screw the side cover and re-install the magnetic side cover.
VIDEO GUIDE
-
6.1 Installation & Usage Video
Please copy the video URL and open it in your browser to view the video. https://youtu.be/2aP5PqltmZc -
Maintenance & Cleaning Video
Please copy the video URL and open it in your browser to view the video. https://youtu.be/r9Hg3WPaqkg -
Installation & Usage Video for PETKIT AIR PURIFIER SMART SPRAY
Please copy the video URL and open it in your browser to view the video. https://youtu.be/Pce7ExQcWhU
BASIC SPECIFICATIONS
A MESSAGE TO OUR VALUED CUSTOMERS
- Thank you for choosing the PETKIT PURA MAX SELF-CLEANING CAT LITTER BOX. PETKIT is committed to creating a better life for you and your fur babies with high-tech products.
- Please read the User Manual carefully before installing and using the product. Any installation and usage indicates that you have carefully read and accepted the User Safety Guide below.
- PETKIT is not responsible for and legally liable for any accidents or injuries resulting from improper use of the product.
- PETKIT reserves the rights of interpretation and revision.
USER SAFETY GUIDE
*Failure to follow the safety guides outlined below can result in product malfunction or other unforeseen losses.
- Please install and use the product as instructed in the User Manual.
- Kittens under six months of age and cats weighing less than 1.5kg are not recommended to use this product.
- Do not expose the product to high temperature and humidity.
- The product is for indoor use only. Avoid direct sunlight exposure and keep it away from open flames.
- Although the device uses low voltages, the power cord being chewed by pets can cause electrical leakage. Please ensure proper guidance for your pets to use the product.
- Use only the original adapter to avoid device damage or safety hazards.
- Place the device on a level surface and prevent it from touching wall.
- Do not lean the device against something else to avoid safety hazards.
- Do not immerse or soak the main unit bottom of the product in water.
- Lift and place the product gently when handling to protect the weight sensor at its bottom.
- If you are not using or moving the product for an extended period, it is recommended to unplug.
- Children should use this product under the supervision and guidance of adults.
- Repairs should only be performed with professionals’ guidance to avoid accidental damage.
- It is prohibited to place objects on the top of the device or press its top to prevent the device from operating improperly.
- Before leaving for an extended period, ensure sufficient cat litter in the box and space in the waste container.
- If you encounter any issues with the product, please contact our customer service for assistance.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>