Logicbus NS-200AFT-T Industrial 10-100 Base-T to 100 Base-FX Media Converter Instruction Manual
- June 4, 2024
- Logicbus
Table of Contents
Logicbus NS-200AFT-T Industrial 10-100 Base-T to 100 Base-FX Media
Converter
Introduction:
The NS-200AF series is a Ethernet (10/100 Base-TX) to Media (100 Base-FX)
converter. The Ethernet supports 10/100M auto negotiation feature and auto
MDI/MDI-X function.
NS-200A can work normally from -30 ~ 75°C and accepts a wide voltage range
from +12 ~ 48 VDC.
Features:
- Automatic MDI/MDI-X crossover for plug-and-play
- Supports both 10/100 Mbps speed auto negotiation
- Store-and-forward
- Full duplex IEEE 802.3x
- Supports +12 ~ +48 VDC voltage
- Supports operating temperatures range -30 ~ 75°C
- DIN-Rail
Specifications
Technology
Standards| IEEE802.3, 802.3u, 802.3x
Processing Type| Store & forward; wire speed switching
MAC Addresses| 1024
Memory Bandwidth| 1.4 Gbps
Interface
RJ-45 Port| 10/100BaseT(X) auto negotiation speed, Full duplex mode, and auto
MDI/MDI-X connection
Fiber Port| 100 Base-FX (SC/ST connectors)
LED Indicators| 10/100M, Link/Act, Full duplex for Fiber Port
Ethernet Isolation| 1500 Vrms 1 minute
Frame Ground for EMS Protection| Yes
Multi Mode (NS-200AFT-T, NS200AFC-T )| Multi mode fiber cables: 50/125,
62.5/125 or 100/140 μm
Distance: 2 km, (62.5/125 μm recommended) for full duplex
Wavelength: 1300 or 1310nm
Min. TX Output: -20 dBm
Max. TX Output: -14 dBm
RX Sensitivity: -32 dBm
Single Mode (NS 200AFCS-T, NS-200AFCS-60T)| Single-mode fiber cables: 9/125μm
Distance: 30 km for NS-200AFCS-T
Distance: 60 km for NS-200AFCS-60T
Wavelength: 1300 ~ 1310nm
Min. TX Output: – 15 dBm for NS-200AFCS-T
Min. TX Output: – 5 dBm for NS-200AFCS-60T
Max. TX Output: -8 dBm for NS-200AFCS-T
| Max. TX Output: 0 dBm for NS-200AFCS-60T
---|---
RX Sensitivity: -34 dBm for NS-200AFCS-T
RX Sensitivity: -35 dBm for NS-200AFCS-60T
Ethernet Transmission distance| Ethernet: 2-pair UTP/STP Cat.3,4,5,
EIA/TIA-568 100-ohm
Fast Ethernet: 2-pair UTP/STP Cat. 5, EIA/TIA-568 100-ohm
Power
Input Voltage Range| +12 ~ +48 VDC (Non-isolation)
Power consumption| 0.12A@24 VDC
LED Indicator| Yes
Protection| Power reverse polarity protection
Frame Ground for EMS Protection| Yes
Case
Mechanical| Plastic (Flammability UL 94V-0)
Dimensions (W x L x H)| 33mm x 85mm x 107mm
Installation| DIN-Rail
Environmental
Operating Temperature| -30°C ~ +75°C
Storage Temperature| -30 ~ +85°C
Ambient Relative Humidity| 10% ~ 90% HR, non-condensing
NS-200AF Series User’s Manual (Version 1.2, Sep/2011) ————— 1
LED functions
Standard RJ45 female connectors are provided. A standard RJ45 plug cable is
necessary to connect your device to the unit since switch that supports auto
crossover. Figure1 shows the LED indicator functions. The module includes an
internal.
Figure1:
NS-200AFC-T/AFCS-T/ AFCS-60T
NS-200AFT-T
Pin Function for Terminal Block
External power supply is connected using the removable terminal block:
+Vs : Power input (+12 ~ +48 VDC) and should be connected to the power supply
(+) GND : Ground and should be connected to the power supply (-)
F.G. : F.G. stands for Frame Ground (protective ground). It is optional. If
you use this pin, it can reduce EMI radiation; improve EMI performance and ESD
protection.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>