Cambridge Casual 2 Piece Bentley Outdoor Porch Rocking Chair Instruction Manual
- June 17, 2024
- CAMBRIDGE CASUAL
Table of Contents
Instruction Manual ASSEMBLY INSTRUCTIONS
TEAK ROCKING CHAIR
IT-130818T
CUSTOMER SERVICE INFORMATION
Please email us at [email protected] for assembly tips, report damage, or request parts.
For faster response, please write down item number, code for missing parts,
attach the purchase receipt and picture of damaged parts.
Toll free number : 1-888-287-4275 from
9:00am to 5.00pm CST (Monday to Friday).
GENERAL INFORMATION & TIPS
- Please read the assembly instructions prior to assembling the Rocking chair.
- To avoid damage, assemble the rocking chair on a non-abrasive surface such as carpet.
- Make sure all bolts tightly fastened before the rocking chair is used.
- This rocking chair is not for commercial use.
Please make sure you have all parts before beginning assembly. Please wait until all steps are completed before tightening bolts.
TOOLS REQUIRED
-
8″ Philips screwdriver (Not provided).
– For tightening all bolts and screws. -
Rubber Mallet (Not provided).
– For tapping in the wooden caps.
PARTS AND HARDWARE LIST
Attached each rocker (E) to right and left side frame (A1 & A2) as picture
shown, connecting front of rocker to front legs first then the back of
rockers. Secure connections with 1 3/4″ Bolts (I). Install Seat (B), back
support (C), and Apron (D) into corresponding holes of right side frame (A1).
Attach the left side frame (A2) onto seat (B), back support (C), and apron
(D). Secure left side frame (A2) using 1 1/4″ bolts (H), as shown. Invert the
chair and repeat step 2 procedure to secure feama Upright the chair.
Apply glue (L) to all holes in arms (F1&F2) and side frame (A1&A2), As shown.
Next, attach right arm (F1) and Left arm (F2) in side frame holes and tenons,
as shown. Insert four 1 3/4″ Screws (J) from underneath arms (F1&F2). Tighten
screws using philip screwdriver. | Attached Support (G) to right and left side
frame (A1 & A2), secure using 1 1/4″ screws (K) as shown. Make sure all parts
are connected and tighten all bolts and screws completely using screwdriver.
Tap in the wooden caps (M) to cover bolts head using rubber mallet.
CONGRATULATION !
THE ROCKING CHAIR IS NOW READY FOR USE.
CARE MAINTENANCE
Due to teak wood’s natural characteristics, wood color and grain variations
may be present. This is a symbol of 0the originality of each unit and gives
each finished piece a distinctive look and inherent charm.
UNFINISH NATURAL TEAK WOOD
Teak Wood, when left bare and unfinished, will naturally fade to a silver-gray
color. This transformation does not in any way affect the functionality and
durability of the furniture.
It is recommended to sand the furniture in regular interval to maintain a
smooth finish. This will also reduce the potential in wood splinter and other
hazard. For customer who would like to maintain the original golden-brown
color, one may best apply teak oil or other compatible clear protective
coating. Please follow the recommendation of the protective coating
manufacturer in both application and the frequency.
Teak wood is a living material that breathe and change over time. If you
choose to maintain the smooth golden-brown finish, it will require regular
maintenance, such as sanding and reapplication of protective coating.
We hope that will be a rewarding experience, as a well-maintained teak
furniture may last many years to come.
Please note, once you stain your teak, it will not return to the natural
golden brown or weathered silver-gray color without sanding off the stain.
Staining is intended to be permanent. If you choose to stain your furniture
after it has turned silver-gray, you must first sand it before applying the
stain.
FINISHED TEAK WOOD
Finished Teak Wood may be maintained with solvent-based polyurethane
protective coating every six (6) months, or as suggested by the protective
coating manufacturers.
For everyday maintenance, you may clean with mild detergent using clean cloth.
Please do not expose and/or use any chemical solvent.
FINISHED WOOD
a. Recommend for every period of 6 months to apply water-based mild detergent
for wood using clean cloth.
b. Do NOT expose to chemical solvent
CUSHIONS
Our fabrics are designed to be breathable. They are water resistant but not
waterproof. It is recommended that you store and remove the cushions when not
in use or during severe weather condition. The cushion and cushion cover shall
be removed and air dried if it is soaked after heavy rain, so we may avoid the
potential mold issue.
The best way to keep your fabrics looking good is to clean them. It is
recommended to clean off dust and dirt periodically, wipe spills as soon as
they occur, and spot clean soon after stains occur. Removable cushion covers
may be machine-washed in cold water with mild laundry soap and air dried.
SYNTHETIC RATTAN AND WOVEN POLYROPE
To clean, use mild soap and clean water – wipe off the dust or spills using
clean cloth (Do NOT use brush). Dry thoroughly with soft cloth or air dried.
Do NOT expose to chemical solvent.
Other Tip:
- Do not put hot items directly on furniture surface.
- Do not store furniture in areas that have central heating or cooling vents to prevent excessive drying of the wood. This will decrease the furniture’s longevity.
- Do not write on furniture without a padded barrier to protect the surface.
- Do not leave your furniture in puddles of water or on wet ground.
- Cover your furniture during winter months or move into covered storage.
The manufacturer supports protection of the world’s forest resources and is diligent in sourcing legally harvested wood
1 Year Limited Warranty
This warranty is a limited warranty. Regular care and maintenance are required
to maintain the warranty. Warranty is to the original purchaser when items are
purchased from one of our authorized retailers and is not transferable. If a
product fails and is under the terms of our limited warranty, the item will be
replaced with a small fee when applicable. In the case of discontinued models,
an item of similar quality and style will be offered to the customer.
-
1 Year Limited Frame Warranty:
Wood frames are warranted to be free from structural defects (i.e., broken frame) in material and workmanship. Wood frames require user maintenance and changes in the color of wood are normal and should be expected to occur over time as the natural material ages. Therefore, natural fading and changes in wood frames is not covered by this warranty. Components such as chair feet are meant to wear and tear, so they will not be considered as part of the frame. -
Finish, when applicable:
The finish is warranted against peeling, cracking, or blistering for a period of 1 year, provided the unit has not been scratched or abraded. Scratches and dents resulting from normal wear and tear are not covered. -
Fabric
Fabrics and cushions are warranted to be free from workmanship or material defects, which includes failures in stitching, zippers, sling rails, cording, buttons, cushion foam, or other areas of workmanship. The fabric and cushion will not be warranted if deterioration, discoloration, fading, etc., is due to exposure of chemicals, cleaning products, sun lotions, oil spills, improper maintenance process, or extreme heat.
Warranty Exclusions:
Furniture used for commercial, contractor or any non-residential purposes |
clearance items, display models, or items purchased “as is” | failure caused
by unreasonable or abusive use, freight damage, acts of nature, vandalism,
fire, lack of proper care and maintenance, or improper assembly | exposure to
severe weather includes, but not limited to, snowstorm, hail, heavy rainfall,
flooding, hurricane, and extreme heat | accidental damage, repair, or
modifications by customer | straps and fabric against fading or discoloration
from improper and/or accidental exposure to elements, oil spills, fluids or
chemicals | hardware against corrosion or rusting | buckling or splitting of
tubing resulting from exposure to water and freezing temperatures.
Further excluded: normal wear and tear | loss of use or time | inconvenience,
money, travel, packaging or any other consequential or incidental damages.
In no event shall the manufacturer’s responsibility exceed the value of the
product.
The warranty starts on the date of purchasing unless otherwise noted. However,
we may consider for special circumstance.
For quality control purposes and verification, we need documents in support of
your claim:
- Packing slip / Invoice
- Additional documents (Photos or video) of damaged/ defected/ missing part
- Item number and part code (can be found on assembly instruction)
Please include the above-mentioned documents as your claim WILL NOT BE
PROCESSED until properly supported. Retain all damaged goods until the claim
is concluded .
The terms of this warranty are subject to change without notice.