GENERAL 75-150 16 Inch Drill Presses Instruction Manual

: June 17, 2024
: GENERAL

75-150 16 Inch Drill Presses

Product Information

Specifications:

Large front mounted stop switch with lock-out safety
feature
Adjustable spindle tension return spring
Built-in lamp to illuminate drilling area
Spindle supported by high quality ball bearings
Cast iron pulleys to reduce vibration
Industrial 1/2 HP motor
Heavy-duty positive depth stop for quick adjustment
5/8 drill chuck
Swing: 13 3/8” (340 mm) – #75-150, 16” (406 mm) –

75-160
Drilling Capacity: 5/8 (16 mm)
Chuck Size: 5/8 (16 mm)
Spindle Travel: 3 1/8 (80 mm)
Spindle Distance to Table: 30 3/4 (781 mm) – #75-150, 30 5/16
(770 mm) – #75-160
Spindle Distance to Base: 48 (1219 mm) – #75-150, 47 11/16
(1212mm) – #75-160
Table Size: 11 3/8 (289 mm) – #75-150, 10 1/2 (268 mm) –

75-160
Column Diameter: 2 7/8 (73 mm)
Number of Speeds: 12
Spindle Speeds: 280-3000 RPM
Spindle Taper: MT 2
Overall Height: 62 (1575 mm)
Base Size: 10 1/4 x 17 1/4 – #75-150, 10 7/8 x 19 3/16 –

75-160
Motor: 1/2 HP, 110 V, 8 A
Weight: 121 LBS (55 kg) – #75-150, 134 LBS (61 kg) –

75-160

Product Usage Instructions:

Assembly:

Read the manual carefully before assembling the drill
press.
Ensure you have all the necessary parts and tools required for
assembly.
Follow the step-by-step instructions provided in the manual to
assemble the drill press.

Installation:

Select a suitable location for the drill press with proper
lighting and ventilation.
Place the drill press on a stable and level surface.
Securely attach the base to the surface using appropriate
fasteners.

Operation:

Make sure the drill press is connected to a properly grounded
electrical outlet.
Ensure the working area is well-lit, clean, and free of
debris.
Wear appropriate personal protective equipment, such as safety
glasses and ear protection.
Verify that the drill bit is securely installed in the chuck
before starting the drill press.
Adjust the spindle tension return spring according to your
drilling requirements.
Use the built-in lamp to illuminate the drilling area.
Position the workpiece on the table and adjust the depth stop
for the desired drilling depth.
Securely clamp or use a hold-down to keep the workpiece in
place.
Start the drill press by turning on the large front-mounted
stop switch.
Gradually lower the spindle to the workpiece using the feed
handles.
Apply consistent and even pressure while drilling.
After drilling, raise the spindle and turn off the drill
press.

FAQ:

Q: What is the purpose of the lock-out safety feature?

The lock-out safety feature on the large front mounted stop
switch prevents unwanted or unintentional start-up of the drill
press, ensuring user safety.

Q: Can I adjust the speed of the drill press?

Yes, this drill press offers 12 different speeds ranging from
280 to 3000 RPM. Refer to the manual for instructions on adjusting
the speed.

Q: How do I maintain the drill press for optimal

performance?

To maintain optimal performance, regularly clean the drill press
and lubricate moving parts as recommended in the manual.
Additionally, ensure that all safety features are in proper working
condition.

Q: What is the warranty coverage for this product?

The warranty coverage extends to the original purchaser. Proof
of purchase, such as a sales invoice or receipt, is required for
warranty claims.

Rotating, 45° tilting, crank-operated work-table with quick release clamp.
Large front mounted stop switch with lock-out safety feature to prevent unwanted or unintentional start-up.
Adjustable spindle tension return spring.
Built-in lamp illuminates the drilling area.
Spindle is supported by high quality ball bearings.
Cast iron pulleys reduce vibration.
Industrial 1/2 HP motor.
Heavy-duty positive depth stop for quick adjustment.
5/8″ drill chuck.

SWING 13 3/8” (340 mm) – #75-150 16” (406 mm) – #75-160
DRILLING CAPACITY 5/8″ (16 mm)
CHUCK SIZE 5/8″ (16 mm)
SPINDLE TRAVEL 3 1/8″ (80 mm)
SPINDLE DISTANCE TO TABLE 30 3/4″ (781 mm) – #75-150 30 5/16″ (770 mm) –

75-160

SPINDLE DISTANCE TO BASE 48″ (1219 mm) – #75-150 47 11/16″ (1212mm) – #75-160
TABLE SIZE 11 3/8″ (289 mm) – #75-150 10 1/2″ (268 mm) – #75-160
COLUMN DIAMETER 2 7/8″ (73 mm)
NUMBER OF SPEEDS 12
SPINDLE SPEEDS 280-3000 RPM
SPINDLE TAPER MT 2
OVERALL HEIGHT 62″ (1575 mm)
BASE SIZE 10 1/4″ x 17 1/4″ – #75-150 10 7/8″ x 19 3/16″ – #75-160
MOTOR 1/2 HP, 110 V, 8 A
WEIGHT 121 LBS (55 kg) – #75-150 134 LBS (61 kg) – #75-160

VERSION 2 – AUGUST 07/12 © Copyright General® International 08/2012

GENERAL® INTERNATIONAL 8360 Champ-d’Eau, Montreal (Quebec) Canada H1P 1Y3 Telephone 514-326-1161 · Fax 514-326-5555 · www.general.ca

THANK YOU for choosing this General® International model 75-150/75-160 drill
press. This drill has been carefully tested and inspected before shipment and if properly used and maintained, will provide you with years of reliable service. To ensure optimum performance and trouble-free operation, and to get the most from your investment, please take the time to read this manual before assembling, installing and operating the unit.
The manual’s purpose is to familiarize you with the safe operation, basic function, and features of this drill as well as the set-up, maintenance and identification of its parts and components. This manual is not intended as a substitute for formal woodworking instruction, nor to offer the user instruction in the craft of woodworking. If you are not sure about the safety of performing a certain operation or procedure, do not proceed until you can confirm, from knowledgeable and qualified sources, that it is safe to do so.
Once you’ve read through these instructions, keep this manual handy for future reference.

Disclaimer: The information and specifications in this manual pertain to the unit as it was supplied from the factory at the time of printing. Because we are committed to making constant improvements, General® International reserves the right to make changes to components, parts or features of this unit as deemed necessary, without prior notice and without obligation to install any such changes on previously delivered units. Reasonable care is taken at the factory to ensure that the specifications and information in this manual corres-

ponds with that of the unit with which it was supplied. However, special orders and “after factory” modifications may render some or all information in this manual inapplicable to your machine. Further, as several generations of this model of drill and several versions of this manual may be in circulation, if you own an earlier or later version of this unit, this manual may not depict your tool exactly. If you have any doubts or questions contact your retailer or our support line with the model number of your unit for clarification.

GENERAL® & GENERAL® INTERNATIONAL WARRANTY
All component parts of General®, General® International and Excalibur by General International ® products are carefully inspected during all stages of production and each unit is thoroughly inspected upon completion of assembly.
Limited Lifetime Warranty Because of our commitment to quality and customer satisfaction, General® and General® International agree to repair or replace any part or component which upon examination, proves to be defective in either workmanship or material to the original purchaser for the life of the tool. However, the Limited Lifetime Warranty does not cover any product used for professionnal or commercial production purposes nor for industrial or educational applications. Such cases are covered by our Standard 2-year Limited Warranty only. The Limited Lifetime Warranty is also subject to the “Conditions and Exceptions” as listed below.
Standard 2-Year Limited Warranty All products not covered by our lifetime warranty including products used in commercial, industrial and educational applications are warranted for a period of 2 years (24 months) from the date of purchase. General® and General® International agree to repair or replace any part or component which upon examination, proves to be defective in either workmanship or material to the original purchaser during this 2-year warranty period, subject to the “conditions and exceptions” as listed below.
To file a Claim To file a claim under our Standard 2-year Limited Warranty or under our Limited Lifetime Warranty, all defective parts, components or machinery must be returned freight or postage prepaid to General® International, or to a nearby distributor, repair center or other location designated by General® International. For further details call our service department at 1-888949-1161 or your local distributor for assistance when filing your claim.
Along with the return of the product being claimed for warranty, a copy of the original proof of purchase and a “letter of claim” must be included (a warranty claim form can also be used and can be obtained, upon request, from General® International or an authorized distributor) clearly stating the model and serial number of the unit (if applicable) and including an explanation of the complaint or presumed defect in material or workmanship.
CONDITIONS AND EXCEPTIONS: This coverage is extended to the original purchaser only. Prior warranty registration is not required but documented proof of purchase i.e. a copy of original sales invoice or receipt showing the date and location of the purchase as well as the purchase price paid, must be provided at the time of claim.
Warranty does not include failures, breakage or defects deemed after inspection by General® or General® International to have been directly or indirectly caused by or resulting from; improper use, or lack of or improper maintenance, misuse or abuse, negligence, accidents, damage in handling or transport, or normal wear and tear of any generally considered consumable parts or components.
Repairs made without the written consent of General® Internationallwill void all warranty.

RULES FOR SAFE OPERATION
To help ensure safe operation, please take a moment to learn the machine’s applications and limitations, as well as potential hazards. General® International disclaims any real or implied warranty and holds itself harmless for any injury that may result from improper use of its equipment.

1. Do not operate the drill press when tired, distracted, or under the effects of drugs, alcohol or any medication that impairs reflexes or alertness.
2. The working area should be well lit, clean and free of debris.
3. Keep children and visitors at a safe distance when the drill press is in operation; do not permit them to operate the drill press.
4. Childproof and tamper proof your shop and all machinery with locks, master electrical switches and switch keys, to prevent unauthorized or unsupervised use.
5. Stay alert! Give your work your undivided attention. Even a momentary distraction can lead to serious injury.
6. Fine particulate dust is a carcinogen that can be hazardous to health. Work in a well-ventilated area and whenever possible use a dust collector and wear eye, ear and respiratory protection devices.
7. Do not wear loose clothing, gloves, bracelets, necklaces or other jewelry while the drill press is in operation.
8. Be sure that adjusting wrenches, tools, drinks and other clutter are removed from the machine and/or the table surface before operating.
9. Keep hands well away from the drill bit and all moving parts. Use a hold- down or clamp to secure the stock, and use a brush, not hands, to clear away chips and dust.
10. Be sure that the drill bit is securely installed in the chuck before operation.
11. Be sure the drill bit has gained full operating speed before beginning to drill.
12. Always use a clean, properly sharpened bit. Dirty or dull bits are unsafe and can lead to accidents.

13. Use suitable work piece support if the work piece does not have a flat surface.
14. Do not push or force the bit into the stock. The drill will perform better and more safely when working at the rate feed for which it was designed.
15. Avoid working from awkward or off balance positions. Do not overreach and keep both feet on floor.
16. Keep guards in place and in working order. If a guard must be removed for maintenance or cleaning be sure it is properly re-attached before using the tool again.
17. Never leave the machine unattended while it is running or with the power on.
18. Use of parts and accessories NOT recommended by GENERAL® INTERNATIONAL may result in equipment malfunction or risk of injury.
19. Never stand on machinery. Serious injury could result if the tool is tipped over or if the drill bit is unintentionally contacted.
20. Always disconnect the tool from the power source before servicing or changing accessories such as bits, or before performing any maintenance, cleaning, or if the machine will be left unattended.
21. Make sure that the switch is in the “OFF” position before plugging in the power cord.
22. Make sure the tool is properly grounded. If equipped with a 3-prong plug, it should be used with a threepole receptacle. Never remove the third prong.
23. Do not use this drill press for other than its intended use. If used for other purposes, GENERAL® INTERNATIONAL disclaims any real implied warranty and holds itself harmless for any injury, which may result from that use.

ELECTRICAL REQUIREMENTS
BEFORE CONNECTING THE MACHINE TO THE POWER SOURCE, VERIFY THAT THE VOLTAGE OF YOUR POWER SUPPLY CORRESPONDS WITH THE VOLTAGE SPECIFIED ON THE MOTOR I.D. NAMEPLATE. A POWER SOURCE WITH GREATER VOLTAGE THAN NEEDED CAN RESULT IN SERIOUS INJURY TO THE USER AS WELL AS DAMAGE TO THE MACHINE. IF IN DOUBT, CONTACT A QUALIFIED ELECTRICIAN BEFORE CONNECTING TO THE POWER SOURCE. THIS TOOL IS FOR INDOOR USE ONLY. DO NOT EXPOSE TO RAIN OR USE IN WET OR DAMP LOCATIONS.

GROUNDING INSTRUCTIONS
In the event of an electrical malfunction or short circuit, grounding reduces the risk of electric shock. The motor of this machine is wired for 110V single phase operation and is equipped with a 3-conductor cord and a 3prong grounding plug to fit a grounded type receptacle . Do not remove the 3rd prong (grounding pin) to make it fit into an old 2-hole wall socket or extension cord. If an adaptor plug is used , it must be attached to the metal screw of the receptacle.
Note: The use of an adaptor plug is illegal in some areas. Check your local codes. If you have any doubts or if the supplied plug does not correspond to your electrical outlet, consult a qualified eletrician before proceeding.

EXTENSION CORDS
If you find it necessary to use an extension cord with your machine, use only 3-wire extension cords that have 3prong grounding plug and a matching 3-pole receptacle that accepts the tool’s plug. Repair or replace a damaged extension cord or plug immediately.
Make sure the cord rating is suitable for the amperage listed on the motor I.D. plate. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The accompanying chart shows the correct size extension cord to be used based on cord length and motor I.D. plate amp rating. If in doubt, use the next heavier gauge. The smaller the number, the heavier the gauge.

TABLE – MINIMUM GAUGE FOR CORD
TOTAL LENGTH OF CORD IN FEET

AMPERE 110 VOLTS 25 FEET 50 FEET 100 FEET 150 FEET RATING 220 VOLTS 50 FEET 100 FEET 200 FEET 300 FEET

AWG

< 5 ——-> 18 6 TO 10 ——-> 18 10 TO 12 ——-> 16 12 TO 16 ——-> 14

16

14

16

14

12

16

14

12

NR
NR
NR = Not Recommended

CIRCUIT CAPACITY
Make sure that the wires in your circuit are capable of handling the amperage draw from your machine, as well as any other machines that could be operating on the same circuit. If you are unsure, consult a qualified electrician. If the circuit breaker trips or the fuse blows regularly, your machine may be operating on a circuit that is close to its amperage draw capacity. However, if an unusual amperage draw does not exist and a power failure still occurs, contact a qualified technician or our service department.

5

14″ OR 16″ DRILL PRESSES
75-150 · 75-160

ASSEMBLY INSTRUCTIONS

Before proceeding with the assembly, read the operating and maintenance instructions manual and familiarize yourself with correct assembly, setup, maintenance and safety procedures.
TO AVOID RISK OF SERIOUS INJURY, MAKE SURE THE DRILL PRESS IS INSTALLED ON A FLAT, SOLID AND STABLE SURFACE.

1. Place the base (1) on a flat surface and screw the column (8), to the base.
2. Remove the rack ring (9) from the column (8).
3. Insert the rack (11) into the table bracket and position the 2 pieces onto the column at the same time. The bottom lip of the rack is pressed between the column and the flange. The top lip of the rack is similarly secured with the replacement of the rack ring (9). Tighten the set screw in the rack ring. Place the handle (10) on the worm gear and secure it with the hex head bolt.
4. Attach the head (2) to the column and tighten the head with the set screws (3).
5. Secure the table onto the table arm.
6. Attach the 3 feed handles, (4, 5 & 6), to the handle body (7).
7. If desired, install a max. 60 watt light bulb (not included) for the worklight (12). Once assembled, clean the protective coating from all surfaces (where applicable) using a rag dipped in kerosene, mineral spirits or paint thinner. (Dispose of potentially flammable solvent-soaked rags according to manufacturer’s safety recommendations.) A putty knife, held flat to avoid scratching the surface, may also be used to scrape off the coating followed by clean-up with solvent. Avoid rubbing painted surfaces, as many solvent-based products will remove paint.
INSTALL THE CHUCK GUARD
Fit the chuck guard onto the quill and tighten the Phillips screw to secure the chuck guard in place.
ADJUSTING AND USING THE CHUCK GUARD
1. Loosen the wing nuts on both sides of the chuck guard and slide the chuck guard extension down along the two slots to the desired height .
2. Tighten the wing nuts to lock the chuck guard exten sion in place.
Note: To facilitate drill bit installation / removal, flip the spring loaded chuck guard up as shown in to keep it out of the way.

REAR VIEW

TO PREVENT THE RISK OF SERIOUS INJURIES, ALWAYS COVER THE CHUCK AND DRILL BIT WITH THE CHUCK GUARD WHEN USING THE DRILL PRESS.
6

INSTALLING THE CHUCK

1. Slide the arbor into the quill assembly, flat end goes in first.

2. Slide the chuck onto the tapered end of the arbor and using the feed

handle, lower the quill assembly against the table to secure the chuck. (To avoid damaging the chuck place a piece of wood on the table.)

Tool

Quill Assembly
Arbor

REMOVING THE CHUCK AND ARBOR

Chuck

1. Turn “OFF” and disconnect the drill from the power source. 2. Using feed handle, lower the quill assembly. 3. Insert tool into, and all the way through the quill assembly.
Note: It may be necessary to rotate the quill in order to be able to get the tool all the way through. 4. While holding onto the chuck to prevent damage, raise the quill assembly. The arbor and chuck should fall out.

ADJUSTMENTS AND CONTROLS
POWER “ON” 1. Make sure the switch is in the “OFF” position and plug the power cord into a matching outlet. 2. Make sure the pulley guard is closed. 3. Check that the chuck or keyless chuck is installed properly. 4. When turning the machine “ON” be aware that the shaft will rotate freely. 5. When the drill press is running check to see if it runs without vibration or shaking. 6. Make sure the table bracket moves up and down smoothly. 7. Make sure the spindle shaft turns smoothly. 8. Unlock the cover, press the green start button for starting machine. Press the red button to stop machine.

WORK-LIGHT SWITCH

POWER ON

POWER OFF
7

ADJUSTING TABLE HEIGHT
1. Loosen the column lock handle (1).
2. Turn the crank handle (2) until the table is at the desired height.
3. Retighten the column lock handle (1) before starting.

TABLE SWING ADJUSTMENT
1. Loosen column lock handle (1).
2. Swing the table arm bracket and the table to the desired position.
3. Retighten column lock handle (1).
When working with taller work pieces swing the table 180° out of the way and use the base as a table.

TABLE ROTATION ADJUSTMENT
1. Loosen the table lock handle (3). 2. Rotate the table to the desired
position. 3. Retighten the table lock
handle (3).

TABLE TILT ADJUSTMENT
1. Loosen the pivot bolt (4) and set screw (5).
2. Tilt the table to the desired angle.
3. Retighten the pivot bolt (4) and set screw (5).

DEPTH STOP ADJUSTMENT
1. Set the bottom edge of nut #1 even with the desired depth setting.
2. Tighten nut #2 against nut #1 to secure it in position.
3. Depth stop is now set and will provide repetitive holes of equal depth.

DRILLING
Always use hold-downs or clamps to secure the workpiece. The workpiece should never be held only by hand. Take care to use clean, sharp bits. Damaged or broken bits could result in serious injury. When drilling flat work, place the worpiece on a wooden base and clamp it down against the table.
For working in wood, machine spur bits are generally preferred. Do not use hand bits, which have a screw tip. At drill press speeds these bits rotate into the workpiece so rapidly that they lift the workpiece off the table and swirl it.
8

CHANGING SPEEDS
MAKE SURE THE DRILL PRESS HAS COME TO A COMPLETE STOP BEFORE CHANGING SPEEDS. REFER TO THE SPINDLE SPEED SELECTION CHART LOCATED ON THE INSIDE OF THE SPINDLE COVER. 1. Disconnect the drill press from the power source. 2. Loosen the slide bar bolt (1) located on the right side of the head. 3. Pull the motor (2) in towards the head to loosen the belts. 4. Relocates belts to the desired pulleys to select a new spindle speed. 5. Push the motor (2) back, away from the head. 6. Retighten the slide bar bolt (1) and check the belt tension.

THE FOLLOWING TABLE CAN BE USED AS A GUIDLINE FOR SELECTING SPEEDS BASED ON BIT SIZE & BIT MATERIAL.

BIT SIZE

CAST STEEL

TOOL STEEL

BIT MATERIAL CAST IRON

MILD STEEL

ALUM. & COPPER

CUTTING SPEED 40 FT/MIN (12 M/MIN) 60 FT/MIN (18 M/MIN) 80 FT/MIN (24 M/MIN) 100 FT/MIN (30 M/MIN) 200 FT/MIN (60 M/MIN)

DIAMETER
1/16″ (2 mm) 1/8″ (3 mm) 3/16″ (5 mm) 1/4″ (6 mm) 5/16″ (8 mm) 3/8″ (10 mm) 7/16″ (11 mm) 1/2″ (13 mm)

1910 – 2445 RPM 1220 -1275 RPM 765 – 815 RPM
610 RPM 480 – 490 RPM 380 – 405 RPM
350 RPM 300 – 305 RPM

REVOLUTIONS PER MINUTE

2865 – 3665 RPM

3820 – 4890 RPM

4775 – 6110 RPM

1835 -1910 RPM

2445 – 2545 RPM

3055 – 3185 RPM

1145 – 1220 RPM

1530 – 1630 RPM

1910 – 2035 RPM

915 – 955 RPM

1220 – 1275 RPM

1530 – 1590 RPM

715 – 735 RPM

955 – 980 RPM

1195 – 1220 RPM

570 – 610 RPM

765 – 815 RPM

955 – 1020 RPM

520 – 525 RPM

700 RPM M/MIN)

870 RPM

440- 460 RPM

590 – 610 RPM

735 – 765 RPM

9550 – 12225 RPM 6110 – 6365 RPM 3820 – 4075 RPM 3055 – 3180 RPM 2390 – 2445 RPM 1910 – 2035 RPM 1740 – 1745 RPM 1470 – 1530 RPM

MAINTENANCE · Keep the unit clean and free of dust and debris. Painted surfaces can be wiped with a damp rag. · Periodically lubricate (oil or grease) all sliding or moving parts including the column and table tilt mechanisms,
brackets, worm gears and the quill. · Bearings in the quill and the V-belt pulley are sealed, permanently lubricated and maintenance free. · Lightly oil the slide bars every 2 months. · If cranking becomes difficult, grease the column bracket.
IMPORTANT: USE ONLY GENERAL INTERNATIONAL OR AUTHORIZED REPLACEMENT PARTS AND ACCESSORIES.

9

RECOMMENDED OPTIONAL ACCESSORIES

We offer a large variety of products to help you increase convenience, productivity, accuracy and safety when using your drill press Here’s a small sampling of optional accessories available from your local General International dealer.
For more information about our products, please visit our website at www.general.ca

25 PIECE – RUBBER DRUM
SANDING SET

75-025

Turn your drill press into a mini drum sander. Ideal for small sanding jobs on curved or odd shaped pieces. Kit includes 5 different sized drums: 1/2″, 3/4″, 1″, 1-1/2″ & 2″ plus 2 sets of 80 grit and 2 sets of 120 grit sanding sleeves for each.

ABRASIVE SLEEVES #70-030
10 piece replacement abrasive sleeve set for 70-025. Includes 5 (one of each size) 80 & 120 grit sanding sleeves.

9″ AUGER DRILL BIT SET

70-105

Heavy duty carbon steel. Heattreated and precision sharpened for quick, accurate and effortless cuts. Includes 6 bits sizes: 1/4″, 5/16″, 3/8″, 1/2″, 5/8″, 3/4″ with 3/8″ shank, in a conve-nient carrying case.

DRILL PRESS TOOL TRAY #70-125
Can be installed on most drill press columns. Made from durable plastic with a metal swivel rod.

12″ X 24″ (305 X 610 MM) UNIVERSAL DRILL PRESS TABLE #70-135 17″ X 32″ (432 X 813 MM) UNIVERSAL DRILL PRESS TABLE #70-140 Adds versatility to your drill press and repeatable accuracy to your work. Includes: 3″ tall 2-pc. Full length fence with t-slot and stop, 2-1/2″ dust port connection, parallel t-slots in table and 2 workpiece holdowns. Mounts to all drill tables with mounting holes.

DRILL PRESS CHUCK · Prevents unintentional user con

GUARD – 70-155

tact with the chuck and bit dur

ing operations.

· Contains wood chips, shavings or other debris for safer drilling.

· Designed to meet the most strin gent industrial and educa tional safety requirements.

· Sturdy cast aluminum body and pact resistant windows.

· Spring loaded flip-up design, allows for quick drill bit changes without interference.

9″ VISE-CLAMP

70-130

Adjustable lock-in clamping pressure and 360 degree rotation; a must for all safety conscious woodworkers. Includes two 1/2″ t-bolts to mount to any drill table with 9/16″ (or wider)mounting holes.

DRILL PRESS VISES

95-140/95-150/95-160

Hold down slots along both sides. High tensile iron casting construction for maximum durability. One-piece cast-iron axial sleeve and movable jaws. Fast action, “Acme” type screw threads.

95-140 (4″) / 95-150 (5″) / 95160 (6″)

10

PART N0.
75150-01 75150-02 75150-03 75150-04 75150-05 75150-06 75150-07 75150-07-1 75150-08 75150-09 75150-10 75150-11 75150-12 75150-12-1 75150-13 75150-14 75150-15 75150-16 75150-17 75150-18N 75150-19 75150-20 75150-21 75150-22N 75150-23 75150-24N 75150-25 75150-26 75150-26-1 75150-26-2 75150-27 75150-28 75150-28-1 75150-29 75150-30 75150-31 75150-32 75150-32-1 75150-33 75150-34 75150-35N 75150-36 75150-37 75150-38N 75150-39 75150-40 75150-40-1

PARTS LIST 75-150
DESCRIPTION
BASE WASHER BOLT BASE FLANGE SCREW CRANK SLEEVE HANDLE TABLE BRACKET TILT SCALE GEAR SHAFT HELICAL GEAR ELEVATING WORM CLAMP BOLT TABLE ARM BRACKET POINTER SET SCREW CLAMP BOLT WASHER BOLT TABLE RACK COLUMN 73 X 1160 SCREW RACK COLLAR FEED HANDLE HANDLE KNOB PINION SHAFT SLEEVE HEAD SET SCREW RUBBER BUSHING SET SCREW BELT TENSION ADJUSTMENT ROD SPRING SCREW SCREW LAMP FRAME LAMP HOLDER NUT NUT SPRING & CAP SWITCH BOX SCREW LIGHT SWITCH ON/OFF SWITCH SCREW ELECTRICAL CORD MOTOR CORD

QTY
1 4 4 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 3 3 1 1 1 1 2 1 1 1 1 4 2 1 1 1 1 1 3 1 1 1 1 1

11

PARTS LIST 75-150

PART N0.

DESCRIPTION

QTY

75150-41

SNAP RING

1

75150-42

DRIVER INSERT

1

75150-43

BEARING

1

75150-44

SNAP RING

1

75150-45

BEARING

1

75150-46

QUILL GASKET

1

75150-47

QUILL

1

75150-48

BEARING

1

75150-49

SUPPORT / CLAMP SEAT DEPTH STOP

1

75150-49-1

NUT

1

75150-50

SCREW

1

75150-51

SPINDLE

1

75150-52

DRIFT KEY

1

75150-53

ARBOR

1

75150-54

CHUCK

1

75150-55

KEY

1

75150-56

BOLT

2

75150-57

MOTOR

1

75150-58

SCREW

2

75150-59

CAPACITOR COVER

1

75150-60

CAPACITOR

1

75150-61

PULLEY GUARD

1

75150-62

MOTOR PULLEY

1

75150-63

SET SCREW

1

75150-64

SNAP RING

1

75150-65

SNAP RING

1

75150-66

BEARING

1

75150-67

MIDDLE PULLEY

1

75150-68

V-BELT

1

75150-69

V-BELT

1

75150-70

KNOB (SEE ITEM #75200-03)

1

75150-71

SCREW

1

75150-72

SHAFT ASSEMBLY

1

75150-73

NUT

1

75150-74

SPINDLE PULLEY

1

75150-75

SCREW

1

75150-76

CORD CLAMP

1

75150-77

ELECTRICAL CORD / LAMP

1

75150-78

SCREW

1

75150-79

SCREW

1

75150-80

KEY HOLDER

1

75150-81

WASHER

1

75150-82

NUT

1

75150-83

SCREW

1

75150-84

DEPTH STOP ROD

1

75150-85

NUT

2

75150-86

DEPTH STOP SUPPORT

1

75150-87

CHUCK GUARD – ITEM #70-115A

1

75150-88

COLUMN PLATE

1

75150-89

WASHER

1

75150-90

SPRING

1

75150-91

WASHER

1

75150-92

CAP SCREW

1

12

DIAGRAM 75-150

64 65
66

SIDE A

67

68

69

40

62

80

63

85(2)

78 77(2)

79

81

75 76 40-1

83 82

84 86

73

33

74

34 SIDE A

40 36(3) 35N26-2
41 39(3) 37
42 38N
43
43
41

51

48

50 52

72

61

60

71

32-1
31 32

40-1 30(2)
29(4) 28-1

56(2)

59 58(2) 57

28 27

26-1

26

25 24N

23(3)

44 22N(3)
45 21

46 92
20

47

89

90 91

19 18N

87 17

49

53

49-1

11

54

7-1

55

12-1

12

88

4
16 13
15 14

10
9
8 7
6 5

3(4) 2(4) 1

13

PART N0.
75160-01 75160-02 75160-03 75160-04 75160-05 75160-06 75160-07 75160-07-1 75160-08 75160-09 75160-10 75160-11 75160-12 75160-13 75160-14 75160-15 75160-16 75160-17 75160-18N 75160-19 75160-20 75160-21 75160-22N 75160-23 75160-24N 75160-25 75160-26 75160-26-1 75160-26-2 75160-27 75160-28 75160-28-1 75160-29 75160-30 75160-31 75160-32-1 75160-33 75160-34 75160-35N 75160-36 75160-37 75160-38N 75160-39 75160-40 75160-40-1 75160-41 75160-42

PARTS LIST 75-160
DESCRIPTION
BASE WASHER BOLT BASE FLANGE SCREW CRANK SLEEVE HANDLE TABLE BRACKET TILT SCALE GEAR SHAFT HELICAL GEAR ELEVATING WORM CLAMP BOLT TABLE ARM BRACKET SET SCREW CLAMP BOLT WASHER BOLT TABLE RACK COLUMN 73 X 1160 SCREW RACK COLLAR FEED HANDLE HANDLE KNOB PINION SHAFT SLEEVE HEAD SET SCREW RUBBER BUSHING SET SCREW BELT TENSION ADJUSTMENT ROD SPRING SCREW SCREW LAMP HOLDER NUT NUT SPRING & CAP SWITCH BOX SCREW LIGHT SWTICH ON/OFF SWITCH SCREW ELECTRICAL CORD MOTOR CORD SNAP RING DRIVER INSERT

QTY
1 4 4 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 3 3 1 1 1 2 1 1 1 1 4 2 1 1 1 1 1 3 1 1 1 1 1 1 1

14

PART N0.
75160-43 75160-44 75160-45 75160-46 75160-47 75160-48 75160-49 75160-49-1 75160-50 75160-51 75160-52 75160-53 75160-54 75160-55 75160-56 75160-57 75160-58 75160-59 75160-60 75160-61 75160-62 75160-63 75160-64 75160-65 75160-66 75160-67 75160-68 75160-69 75160-70 75160-71 75160-72 75160-73 75160-74 75160-75 75160-76 75160-77 75160-78 75160-79 75160-80 75160-81 75160-82 75160-83 75160-84 75160-85 75160-86 75160-87 75160-88 75160-89 75160-90 75160-91 75160-92

PARTS LIST 75-160
DESCRIPTION
BEARING SNAP RING BEARING QUILL GASKET QUILL BEARING SUPPORT / CLAMP SEAT DEPTH STOP NUT SCREW SPINDLE DRIFT KEY ARBOR CHUCK KEY BOLT MOTOR SCREW CAPACITOR COVER CAPACITOR PULLEY GUARD MOTOR PULLEY SET SCREW SNAP RING SNAP RING BEARING MIDDLE PULLEY V-BELT V-BELT KNOB (SEE ITEM #75200-03) SCREW SHAFT ASSEMBLY NUT SPINDLE PULLEY SCREW CORD CLAMP ELECTRICAL CORD / LAMP SCREW SCREW KEY HOLDER WASHER NUT SET SCREW DEPTH STOP ROD NUT DEPTH STOP SUPPORT CHUCK GUARD – ITEM #70-115A COLUMN PLATE WASHER SPRING WASHER CAP SCREW

QTY
1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1

15

DIAGRAM 75-160

64

66

65

67

68

69

40

63

80 85(2)

78 77(2)

79

81

84

75 76 40-1

83

86

82

73

74

33 34

SIDE A

40

35N

36(3) 26-2

41 39(3) 37
42 38N
43

43 41

72

61

71

40-1 32-1
30(2)

31 32

29(4)

28-1

56(2)

28 27

26-1

26

25 24N

23(3)

44

22N(3)

45

21

46

92

47

20

89

90 91

62
60
59 58(2) 57

51

48

50 52

19 18 N

87 17

49

53

49-1

11

54
55 12

7-1
12-1

88

4

16

13

15 14

10
9
8 7
6 5

3(4) 2(4) 1

16

NOTES:

17

75-150 & 75-160
8360 Champ-d’Eau, Montreal (Quebec) Canada H1P 1Y3 Tel.: 514-326-1161
Fax: 514-326-5565 – Parts & Service / Fax: 514-326-5555 – Order Desk
orderdesk@general.ca www.general.ca
IMPORTANT When ordering replacement parts, always give the model number, serial number of the machine and
part number. Also a brief description of each item and quantity desired.