GENERAL 60-350 14 Inch Cold Cut Saw Electronic Variable Speed Instruction Manual

: June 17, 2024
: GENERAL

Table of Contents

GENERAL 60-350 14 Inch Cold Cut Saw Electronic Variable Speed
FEATURES
SPECIFICATIONS
GENERAL® INTERNATIONAL WARRANTY
RULES FOR SAFE OPERATION
ELECTRICAL REQUIREMENTS
IDENTIFICATION OF MAIN PARTS AND COMPONENTS
UNPACKING
ASSEMBLY INSTRUCTIONS
BASIC ADJUSTMENTS & CONTROLS
OPERATING INSTRUCTIONS
MAINTENANCE
BLADE SPECIFICATIONS
WIRING DIAGRAM
CONTACT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

GENERAL 60-350 14 Inch Cold Cut Saw Electronic Variable Speed

FEATURES

A powerful 3 HP motor provides plenty of power to suit a wide variety of cutting applications.
Variable blade speed – ideal for cutting ferrous materials.
Mitering capabilities – stops at 90°, 45° left and 45° right.
Heavy-duty spindle and worm gearbox.
Quick-clamp vice for easy workpiece loading.
Control handle with safety trigger switch.
Coolant pump system with high volume tank.
Specially designed water channel for better cooling effect.
Shock-proof control panel.
Overload-protected inverter.
Digital spindle speed display.

SPECIFICATIONS

Cutting capacity at 90º
- 3 3/8” (85 mm)
- 4 3/4” (120 mm) 3” (75 mm)
- 4” x 4” (102 x 102 mm)
- 6 1/8” x 3 1/2” (155 x 90 mm)
Cutting capacity at 45°
- 3” (75 mm)
- 3 3/4” (95 mm)
- 3 1/8” x 3 1/8” (80 x 80 mm)
- 3 1/8” x 2 3/4” (80 x 70 mm)
Blade: 14” x 1 1/4” (350 x 32 mm) – optional
Spindle speed: 24 to120 rpm
Maximum vise opening: 6 11/16” (170 mm)
Coolant pump: 1/8 HP
Coolant tank: 5 liters
Overall dimensions: 47 1/4” x 40 1/8” x 76 3/4” (1200 x 1020 x 1950 mm)
Stand dimensions: 23 5/8” x 22 13/16” x 28 3/8” (600 x 580 x 720 mm)
Motor: 3 HP, 220 V, 3 Ph, 9.6 A
Weight: 550 lbs (250 kg)

THANK YOU
for choosing this General® International model 60-350 14” variable speed cold cut saw. This cold-cut saw has been carefully tested and inspected before shipment and if properly used and maintained, will provide you with years of reliable service. For your safety, as well as to ensure optimum performance and trouble-free operation, and to get the most from your investment, please take the time to read this manual before assembling, installing and operating the unit.
The manual’s purpose is to familiarize you with the safe operation, basic function, and features of this cold-cut saw as well as the set-up, maintenance and identification of its parts and components. This manual is not intended as a substitute for formal metalworking instruction, nor to offer the user instruction in the craft of metalworking. If you are not sure about the safety of performing a certain operation or procedure, do not proceed until you can confirm, from knowledgeable and qualified sources, that it is safe to do so. Once you’ve read through these instructions, keep this manual handy for future reference.

DISCLAIMER: The information and specifications in this manual pertain to the unit as it was supplied from the factory at the time of printing. Because we are committed to making constant improvements, General® International reserves the right to make changes to components, parts or features of this unit as deemed necessary, without prior notice and without obligation to install any such changes on previously delivered units. Reasonable care is taken at the factory to ensure that the specifications and information in this manual correspond with that of the unit with which it was supplied. However, special orders and ”after factory” modifications may render some or all information in this manual inapplicable to your machine. Further, as several generations of this model of cold cut saw and several versions of this manual may be in circulation if you own an earlier or later version of this unit, this manual may not depict your unit exactly. If you have any doubts or questions contact your retailer or our support line with the model and serial number of your unit for clarification.

GENERAL® INTERNATIONAL WARRANTY

All parts of General® International and Excalibur by General International® products are carefully inspected during all stages of production and each unit is thoroughly inspected upon completion of assembly.

Limited Lifetime Warranty
Because of our commitment to quality and customer satisfaction, General® International agrees to repair or replace any part or component which upon examination, proves to be defective in either workmanship or material to the original purchaser for the life of the tool. However, the Limited Lifetime Warranty does not cover any product used for professional or commercial production purposes or industrial or educational applications. Such cases are covered by our Standard 2-year Limited Warranty only. The Limited Lifetime Warranty is also subject to the ”Conditions and Exceptions” as listed below.
Standard 2-Year Limited Warranty
All products not covered by our lifetime warranty including products used in commercial, industrial and educational applications are warranted for 2 years (24 months) from the date of purchase. General® International agrees to repair or replace any part or component which upon examination, proves to be defective in either workmanship or material to the original purchaser during this 2-year warranty period, subject to the ”conditions and exceptions” as listed below.
To file a Claim
To file a claim under our Standard 2-year Limited Warranty or under our Limited Lifetime Warranty, all defective parts, components or machinery must be returned freight or postage prepaid to General® International, or to a nearby distributor, repair centre or other location designated by General® International. For further details call our service department at 1-888-949-1161 or your local distributor for assistance when filing your claim.
Along with the return of the product being claimed for warranty, a copy of the original proof of purchase and a ”letter of claim” must be included (a warranty claim form can also be used and can be obtained, upon request, from General® International or an authorized distributor) clearly stating the model and serial number of the unit (if applicable) and including an explanation of the complaint or presumed defect in material or workmanship.

CONDITIONS AND EXCEPTIONS
This coverage is extended to the original purchaser only. Prior warranty registration is not required but documented proof of purchase i.e. a copy of the original sales invoice or receipt showing the date and location of the purchase as well as the purchase price paid, must be provided at the time of claim. Warranty does not include failures, breakage or defects deemed after inspection by General® International to have been directly or indirectly caused by or resulting from; improper use, or lack of or improper maintenance, misuse or abuse, negligence, accidents, damage in handling or transport, or normal wear and tear of any generally considered consumable parts or components.
Repairs made without the written consent of General® International will void all warranty.

RULES FOR SAFE OPERATION

To help ensure safe operation, please take a moment to learn the machine’s applications and limitations, as well as potential hazards. General® International disclaims any real or implied warranty and holds itself harmless for any injury that may result from the improper use of its equipment.

Do not operate the saw when tired, distracted, or under the effects of drugs, alcohol or any medication that impairs reflexes or alertness.
The work area should be well-lit, clean and free of debris.
Keep children and visitors at a safe distance when the saw is in operation; do not permit them to operate the saw.
Childproof and tamper-proof your shop and all machinery with locks, master electrical switches and switch keys, to prevent unauthorized or unsupervised use.
STAY ALERT! Give your work your undivided attention. Even a momentary distraction can lead to serious injury.
Fine particulate dust is a carcinogen that can be hazardous to health. Work in a well-ventilated area and whenever possible use a dust collector and wear eye, ear and respiratory protection devices.
Do not wear loose clothing, gloves, bracelets, necklaces or other jewellery while the saw is in operation. Wear protective hair covering to contain long hair and wear non-slip footwear.
Be sure that adjusting wrenches, tools, drinks and other clutter are removed from the machine and/or the table surface before operating.
Keep hands well away from the blade and all moving parts. Use a brush, not hands, to clear away chips and dust.
Be sure that the blade is securely installed and that improper cutting direction is before operation.
Be sure the blade has gained full operating speed before beginning to cut.
Always use a clean, properly sharpened blade. Dirty or dull blades are unsafe and can lead to accidents.
Do not push or force stock into the blade. The saw will perform better and more safely when working at the rate for which it was designed.
To minimize the risk of injury in the event of a workpiece kickback, never stand directly in line with the blade or in the potential kickback path of the workpiece.
Avoid working from awkward or off-balance positions.
Do not overreach while cutting; keep both feet on the floor. Use outfeed support or have an assistant help when cutting long material.
Keep blade guards in place and working order.
If a guard must be removed for maintenance or cleaning, be sure it is properly re-attached before using the tool again.
Never leave the machine running with the power on when not in operation.
Use of parts and accessories NOT recommended by General® International may result in equipment malfunction or risk of injury.
Never stand on machinery. Serious injury could result if the tool is tipped over or if the blade is unintentionally contacted.
Always disconnect the tool from power before servicing or changing accessories such as blades, or before performing any maintenance, cleaning or adjustments, or if the machine will be left unattended.
Make sure that the switch is in the” OFF” position before plugging in the power cord.
Make sure the tool is properly grounded. If equipped with a 3-prong plug it should be used with a three-pole receptacle. Never remove the third prong.
Do not use this saw for any purpose other than its intended use. If used for other purposes, General® International disclaims any real or implied warranty and holds itself harmless for any injury, which may result from that use.

ELECTRICAL REQUIREMENTS

BEFORE CONNECTING THE MACHINE TO THE POWER SOURCE, VERIFY THAT THE VOLTAGE OF YOUR POWER SUPPLY CORRESPONDS WITH THE VOLTAGE SPECIFIED ON THE MOTOR I.D. NAMEPLATE. A POWER SOURCE WITH GREATER VOLTAGE THAN NEEDED CAN RESULT IN SERIOUS INJURY TO THE USER AS WELL AS DAMAGE TO THE MACHINE. IF IN DOUBT, CONTACT A QUALIFIED ELECTRICIAN BEFORE CONNECTING TO THE POWER SOURCE.
THIS TOOL IS FOR INDOOR USE ONLY. DO NOT EXPOSE TO RAIN OR USE IN WET OR DAMP LOCATIONS.

ELECTRICAL CONNECTIONS
Both a manual circuit breaker (or similar device) as well as an electrical plug (similar to the one shown) are recommended and SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN.
Use locally approved wire A which includes a separate grounding wire and a 3-prong grounding type plug B with a matching receptacle C.

GROUNDING INSTRUCTIONS
In the event of an electrical malfunction or short circuit, grounding reduces the risk of electric shock to the operator. The motor of the ”M1” model of this machine is wired for 220 V single-phase operation. As with many stationary industrial type machines, because each installation situation is unique, this machine is supplied without a power cord or plug. The installation of an appropriate power cord and plug must be performed by a qualified electrician. The machine must be connected to an electrical source using a power cord that has a grounding wire, which must also be properly connected to the grounding prong on the plug. The outlet must be properly installed and grounded and all electrical connections must be made under all local codes and regulations.
CIRCUIT CAPACITY
Make sure that the wires in your circuit are capable of handling the amperage drawn from your machine, as well as any other machines that could be operating on the same circuit. If you are unsure, consult a qualified electrician. If the circuit breaker trips or the fuse blows regularly, your machine may be operating on a circuit that is close to its amperage draw capacity. However, if an unusual amperage draw does not exist and a power failure still occurs, contact a qualified technician or our service department.
EXTENSION CORDS
The use of an extension cord is not generally recommended for 220 V equipment. If you find it necessary, use only 3-wire extension cords that have a 3-prong grounding plug and a matching 3-pole receptacle that accepts the tool’s plug. Repair or replace a damaged extension cord or plug immediately. Make sure the cord rating is suitable for the amperage listed on the motor I.D. plate. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The accompanying chart shows the correct size extension cord to be used based on cord length and motor I.D. plate amp rating. If in doubt, use the next heavier gauge.

IDENTIFICATION OF MAIN PARTS AND COMPONENTS

A. LEVELING BOLT (4)
B. ELECTRONIC INVERTER ACCESS DOOR
C. SWIVEL BASE LOCK LEVER
D. VISE HANDLE
E. QUICK LOCK LEVER
F. VISE
G. BLADE GUARD
H. DOWNFEED HANDLE
I. PANEL CONTROL
J. MOTOR
K. WORKPIECE STOP BAR
L. DEPTH STOP
M. MITER SCALE
N. WORKPIECE STOP

UNPACKING

Carefully unpack and remove the unit and its components from the box and check for missing or damaged items as per the list of contents below.
NOTE: PLEASE REPORT ANY DAMAGED OR MISSING ITEMS TO YOUR GENERAL® INTERNATIONAL DISTRIBUTOR IMMEDIATELY.

LIST
OF CONTENTS QTY

A. DOWNFEED HANDLE………………………………………………………. 1
B. WORKPIECE STOP ASSEMBLY…………………………………………… 1
C. TABLE EXTENSION ROLLER……………………………………………….. 1
D. VISE HANDLE………………………………………………………………….. 1
E. HEX HEAD BOLT W/NUT…………………………………………………… 4
F. 10 MM ALLEN KEY………………………………………………………….. 1
G. 4 MM ALLEN KEY……………………………………………………………. 1

ADDITIONAL REQUIREMENTS FOR SET UP

A. 5 & 6 MM ALLEN KEYS
B. PHILLIPS SCREWDRIVER
C. 12 MM WRENCH
D. WRENCH

BASIC FUNCTIONS

This General International model 60-350 14” slow-speed cold cut saw is designed for multipurpose cutting applications in all types of metal fabrication shops.
With the correct carbide or hi-speed steel blade, the built-in coolant system, and its low rpm blade speed this unit is designed to produce cleaner more accurate cuts, as compared to abrasive wheels, on a variety of materials including, aluminium, steel, and brass and other workpieces of various sizes and profiles.

PLACEMENT WITHIN THE SHOP / SAFETY ZONE

THIS COLD CUT SAW MODEL 60-350 IS HEAVY. DO NOT OVER-EXERT. A HOIST OR FORKLIFT WITH STRAPS SHOULD BE USED TO LIFT THIS MACHINE. TO LIMIT THE RISK OF SERIOUS INJURY OR DAMAGE TO THE MACHINE, ANY EQUIPMENT USED TO LIFT THIS MACHINE SHOULD HAVE A RATED CAPACITY ABOVE 550 LBS (250 KG).

PLACEMENT WITHIN THE SHOP
This machine should be installed and operated only on a solid, flat and stable floor that can support the weight of the machine (550 lbs – 250 kg) and the operator. Using the dimensions shown as a guideline, plan for placement within your shop that will allow the operator to work unencumbered and unobstructed by foot traffic (either passing shop visitors or other shop workers) or other tools or machinery.
ESTABLISHING A SAFETY ZONE
For shops with frequent visitors or multiple operators, it is advisable to establish a safety zone around shop machinery. A clearly defined ”no-go” zone on the floor around each machine can help avoid accidents that could cause injury to either the operator or the shop visitor. It is advisable to take a few moments to either paint (using non-slip paint) or use tape and define on the floor the limits or perimeter of each machine’s safety zone. Take steps to ensure that all operators and shop visitors are aware that these areas are off-limits whenever a machine is running for everyone but the individual operating the unit.

ASSEMBLY INSTRUCTIONS

BEFORE ASSEMBLING, MAKE SURE THAT THE SWITCH IS IN THE ”OFF” POSITION AND THAT THE POWER CORD IS UNPLUGGED. DO NOT PLUG IN OR TURN ON THE MACHINE UNTIL YOU HAVE COMPLETED THE ASSEMBLY AND INSTALLATION STEPS DESCRIBED IN THIS SECTION OF THE MANUAL.

For your convenience, this saw is shipped from the factory partially assembled and requires only minimal assembly and set-up before being put into service.

INSTALLING THE DOWN FEED HANDLE

Remove plug A by hand.
Screw the down feed handle into the gearbox in place of the plug.
Secure the down feed handle by tightening two jam nuts with a wrench.
Turn the handle so that the trigger points up.
Secure the handle by tightening jam nut A.
Connect the trigger control cable to the electrical box on the motor as shown.

INSTALLING A BLADE

There are a variety of different types of blades on the market to suit various cutting applications. Your results may vary based on usage, experience and personal preference. Ask your local tool dealer for suggestions for 14” x 1 1/4” (350 X 32 mm) cold-cut blades. Please note that General International offers an optional 14” high-speed steel general-purpose blade (#60-355).
Note: See section ”Parts list and diagrams” for the blade specifications.

To install a blade, remove the screw A on the guard using a 4 mm Allen key.
Detach the guard arm and slide open the guard.
Remove the blade flange screw using a 10 mm Allen wrench. Turn clockwise as shown.
Remove the blade flange from the blade holder.
Install the blade on the blade holder, making sure that the blade is installed with the teeth pointing down as shown B.
Hold the blade against the blade holder making sure it sits flush, then align the two mounting holes C with the corresponding holes on the blade holder.
Re-install the blade flange and thread the mounting screws on 2-3 turns only.
Align the two pins on the blade flange with the corresponding holes in the blade and the blade holder A.
Push on the flange to seat it flush against the blade.
Tighten the mounting screw counterclockwise to secure the flange and the blade to the holder.
Lower the blade guard and re-install the blade guard arm on its pivot B as shown.
Secure the arm to the blade guard using a 5 mm Allen key.

INSTALLING THE TABLE EXTENSION ROLLER

Remove the two screws and flat washers on the left side of the machine with a 6 mm Allen key.
Align the roller slots with the holes in the machine and secure them in place with screws and washers.

Note: Adjust the support roller height as needed along the slotted mounting holes.

INSTALLING THE WORKPIECE STOP

Remove the workpiece stop support using a 5 mm Allen key. Insert the support into the workpiece mounting hole located in the base of the cutting head.
Using a rubber mallet, tap gently on the support to insert it all the way into the mounting hole.
Insert the end of the workpiece stop arm into the support.
Retighten the cap screw to lock the workpiece stop arm in place.
Turn the workpiece stop by hand to place it in the vertical position.

Tip: The workpiece stop has two adjustment points: Position the main adjustment block A that slides on the graduated bar using lock knob B. The smaller fine-tuning adjustment bar C can be set using lock knob D.

INSTALLING THE VISE HANDLE

Screw the handle into the mounting hole on the vice handwheel.
Tighten the handle using a 12 mm wrench.

BASIC ADJUSTMENTS & CONTROLS

TO REDUCE THE RISK OF SHOCK OR FIRE DO NOT OPERATE THE UNIT WITH A DAMAGED POWER CORD OR PLUG. REPLACE THE DAMAGED CORD OR PLUG IMMEDIATELY. TO AVOID UNEXPECTED OR UNINTENTIONAL START-UP, MAKE SURE THE POWER SWITCH IS IN THE OFF POSITION BEFORE CONNECTING TO A POWER SOURCE.

CONNECTING TO A POWER SOURCE
Once the assembly steps have been completed, plug the power cord into an appropriate outlet. Refer back to the section entitled ”Electrical Requirements” and make sure all requirements and grounding instructions are followed. When cutting operations have been completed, unplug the saw from the power source.

MAGNETIC SWITCH
This machine is equipped with a magnetic safety switch designed to protect the unit and the user from power surges, power outages or unintentional start-up. The switch assembly is equipped with a green ”start” button A, a red ”stop” button B and an emergency stop button with twist lock-out device C. Once this button has been pressed, the machine can only be restarted by turning the button to the right to release the stop button, E. The coolant system pump is controlled using switch D. To start the pump, turn the switch to the right. To stop the pump, turn the switch to the left.

BLADE SPEED ADJUSTMENT

The blade speed ranges from 24 to 120 rpm. The blade speed control knob is located on the control box, just above the on button.
Turn the knob clockwise to increase the blade speed.
Turn the knob counterclockwise to decrease the blade speed.
Blade speed will appear on the digital speed display B.

ELECTRONIC SYSTEM PROTECTOR

The electronic inverter of this machine is equipped with an overload protection feature. To prevent an electrical overload from damaging the motor, in the event of a spike in line voltage or amperage draw, the internal electronic system protector will automatically cut off power to the motor and display an error message indicating the cause of the electrical problem.
Common causes of such overloads:

Overworking the motor by forcing the saw, particularly with thicker denser material, thereby causing an increase in power consumption and a spike in amperage draw.
An electrical extension cord that is too long or not the correct gauge of wire can also cause an increase in amperage draw. If an electric extension cord must be used, follow the instructions and refer to the chart in the electrical requirements section at the beginning of this manual.
An overworked circuit is caused by operating on a circuit that is close to its amperage draw capacity. Make sure the circuit being used is capable of handling the amperage drawn from this machine as well as any other electrical devices operating on the same circuit. If you are unsure, consult a qualified electrician.

If the digital speed display on the control box indicates one of the error messages listed below*, wait a few seconds until the message disappears from the screen, then proceed as follows to reset the electronic system protector in and restart the machine.

Remove the box control cover using a 3 mm Allen key.
Press button C (STOP) then press button D (RUN). Re-install the box cover before restarting the machine.

ADJUSTING THE CUT ANGLE

To unlock the swivel base push lever A to the left as shown.
Refer to the graduated scale B at the base of the saw head to set the blade to the required angle.

ADJUSTING THE SWIVEL BASE LOCK LEVER

If the lever does not lock the base securely, loosen the screw C with a 6 mm Allen key while holding the lever in place on its shaft.
Turn the lever to the right, and then retighten the screw A. Make sure the lever locks the swivel base. If not, repeat steps 1 & 2.

ADJUSTING AND USING THE VISE

Position the workpiece in the vice and secure it in place using the vice handwheel D.
Lock the workpiece in place by turning the quick locking lever to the left as shown.
To adjust the vice jaw, loosen screw A with a 10 mm Allen key. Slide the jaw right or left to the desired position, then retighten screw A.

Note: Pull back the vice assembly to allow the rotation of the saw head to the right, especially for mitre cuts.

Note: Adjustment required for mitre cuts.

ADJUSTING THE SAW HEAD STOPS

If the down feed handle is difficult to reach in the up position, loosen jam nut B with a 19 mm wrench, then loosen bolt C until the desired handle height is reached. Retighten jam nut B.
To adjust the saw head in the down position, loosen jam nut D with a 19 mm wrench, then turn bolt E clockwise or counterclockwise as per the adjustment desired. Retighten jam nut D.

IMMOBILIZING THE MACHINE
Machine vibration during operation may cause the machine to move, particularly when installed on uneven surfaces.
The bolt-down tabs and anchor bolts F can be used to help keep the machine immobilized by either lowering the bolts against the floor to act as another point of contact with the floor, or for permanent installations, by drilling into the floor and bolting the machine in place.

OPERATING INSTRUCTIONS

CHECKLIST BEFORE STARTING

VERIFY ALL CHECKPOINTS BEFORE STARTING. FAILURE TO COMPLY CAN RESULT IN SERIOUS INJURIES.

Make sure you and any assistants are wearing safe and appropriate workshop attire.
To reduce the risk of damage to the machine, as well as the potential for personal injury, after initial set-up as well as before each use, make sure that everything is securely installed and that all fasteners and moving parts on this machine are locked in place before starting the machine.
Make sure to have on safety glasses as well as hearing or/or respiratory protection at all times when using the machine.
Check the level of coolant in the tank and fill it as necessary. The maximum level is 5 litres.
Use only recommended parts and accessories. The use of parts or accessories NOT recommended by GENERAL® INTERNATIONAL may result in a risk of injury or damage to the machine.
Be sure that adjusting wrenches, tools, drinks and other clutter are removed from the machine and/or the table surface before operating.

OPERATIONS STEP-BY-STEP

NEVER USE THE SAW WITHOUT ALL GUARDS AND COVERS IN PLACE. BEFORE STARTING THE SAW BE SURE THAT THE BLADE IS NOT ALREADY IN CONTACT WITH THE WORKPIECE.

Trace the cutting line on your workpiece with a pencil and clamp the material firmly in the vice jaws.
Make sure the workpiece is properly secured in the vice.
Note: Use the work stop to quickly and accurately cut multiple pieces of stock to the same length.
Press button A to start the machine. Adjust the blade speed with knob B.
Turn on the coolant pump by turning switch C to the right and opening the coolant valve D.
Press on the down feed handle trigger while smoothly lowering the saw head.
Once the cut is completed, raise the head and release the trigger. Turn OFF the pump by turning switch C to the left.
Press button E to turn off the machine.
Carefully remove the workpiece from the vice.

BURN DANGER: DO NOT USE BARE HANDS TO TOUCH THE WORKPIECE AT THE CUT LOCATION UNTIL IT HAS COOLED.

Note: Before operation, see the chart below regarding the cutting capacity of your machine based on the size and shape of the workpiece.

MAKE SURE THE MACHINE HAS BEEN TURNED OFF AND UNPLUGGED FROM THE POWER SOURCE BEFORE PERFORMING ANY MAINTENANCE OR ADJUSTMENTS.

MAINTENANCE

CLEANING
For optimum performance from your machine follow this maintenance schedule and refer to any specific instructions given in this section. After using your machine, sweep up and discard any excess metal chips and debris.

CHANGING THE GEARBOX OIL

Position the saw head in the down position. Remove the oil plug A with an 18 mm wrench to drain the gearbox. Once the used oil is drained, re-install the plug A.
Remove the down feed handle using a wrench to access the filling hole.
Fill the gearbox with 1,5 litres of 460-grade gear oil. Re-install the down feed handle (see section ”Installing the downfeed handle”).

MAKE SURE THE MACHINE HAS BEEN TURNED OFF AND UNPLUGGED FROM THE POWER SOURCE BEFORE PERFORMING ANY MAINTENANCE OR ADJUSTMENTS.

FUSE REPLACEMENT

Shut off the power source by turning the lock-out safety switch counterclockwise.
Remove the two front plate screws with a Phillips screwdriver.
Remove the front plate to access the cabinet door latch.
Pull back the latch as shown.
Open the latch and then open the cabinet door.
Note: The cabinet door can’t be opened if the power source is not shut off with the safety lock-out switch (step 1).
Remove the used fuse and replace it with one of the same amperage. Then close the cabinet door to restart the machine.

DIAGRAM

PARTS LIST

IMPORTANT: When ordering replacement parts, always give the model number, serial number of the machine and part number. Also a brief description of each item and quantity desired.

PART # DESCRIPTION SPECIFICATIONS QTY

60350-A01 BASE LOCK LEVER 1
60350-A02 NYLOCK NUT 1
60350-A03 CAP SCREW 1
60350-A04 CAP SCREW M8 X 25 2
60350-A05 WASHER 5/16” 2
60350-A06 CONNECTOR 1
60350-A07 RUBBER GASKET 1
60350-A08 HEAD BASE 1
60350-A09 CAP SCREW M8 X 16 2
60350-A10 WASHER 5/16” 2
60350-A11 SPLASH GUARD PLATE 1
60350-A12 SCREW 2
60350-A13 SPLASH GUARD 2
60350-A14 CAP SCREW 2
60350-A15 ROLLER 1
60350-A16 ROLLER BRACKET 1
60350-A17 HANDWHEEL 1
60350-A18 SUPPORT ROD 1
60350-A19 SWIVEL BASE 1
60350-A20 SLIDE BASE 1
60350-A21 RETENTION RING 1
60350-A22 CENTER SHAFT 1
60350-A23 CAP SCREW M8 X 20 1
60350-A24 WASHER M10 1
60350-A25 HANDLE 1
60350-A26 SET SCREW 1
60350-A27 BEARING COVER 1
60350-A28 BEARING 1
60350-A29 BUSHING 1
60350-A30 SPRING 1
60350-A31 LEAD SCREW 1
60350-A32 QUICK LOCK LEVER 1
60350-A33 SLIDING VISE 1
60350-A34 SET SCREW 3
60350-A35 WASHER 3
60350-A36 NUT 3
60350-A37 GIB 1
60350-A38 SLIDING JAW 1
60350-A39 FIXED VISE (SMALL) 1
60350-A40 CAP SCREW M5 X 25 3
60350-A41 SMALL JAW 1
60350-A42 GROOVED JAW 1
60350-A43 STOP PLATE 1
60350-A44 CAP SCREW M8 X 20 2
60350-A45 CAP SCREW M8 X 25 2
60350-A46 PLATE (VISE) 1
60350-A47 CAP SCREW M8 X 25 1
60350-A48 WASHER 1
60350-A49 DUST PLATE 1
60350-A50 MOUNTING PLATE 1
60350-A51 SCREW 1
60350-A52 SPRING 1
60350-A53 LOWER PIVOT ARM 1
60350-A54 WASHER 2
60350-A55 CAP SCREW 2
60350-A56 NUT 1
60350-A57 WASHER 1
60350-A58 LINK PLATE W/THREAD 1
60350-A59 UPPER PIVOT ARM 1
60350-A60 CAP SCREW M6 X 12 1
60350-A61 WASHER 1/4” 1
60350-A62 CAP SCREW M8 X 20 3
60350-A63 WASHER 5/16” 2
60350-A64 LINK PLATE 1
60350-A65 RETENTION RING 1
60350-A66 BLADE GUARD 1
60350-A67 SCREW M5 X 10 7
60350-A68 PLATE 1
60350-A69 GASKET 2
60350-A70 BLADE COVER 1
60350-A71 PLATE 1
60350-A72 CAP SCREW M12 X 35 1
60350-A73 FLANGE 1
60350-A74 SAW BLADE (OPTIONAL #60-355) 350MM 1
60350-A75 BLADE HOLDER 1
60350-A76 OIL SEAL 50.72.8. 1
60350-A77 TAPERED ROLLER BEARING 32008 2
60350-A78 SPINDLE SLEEVE 1
60350-A79 SPROCKET WASHER 1
60350-A80 NYLOCK NUT 1
60350-A81 SPACER 1
60350-A82 WORM GEAR 1
60350-A83 BUSHING 1
60350-A84 PLATE STOP 1
60350-A85 LOCK WASHER 2
60350-A86 NYLOCK NUT 1
60350-A87 MACHINE HEAD 1
60350-A88 BEARING 6301 1
60350-A89 WORM SHAFT 1
60350-A90 BEARING 5305 1
60350-A91 OIL SEAL 25 X 52 X 10 1
60350-A92 COUPLING 1
60350-A93 MOTOR 3HP 1
60350-A94 STRAIN RELIEF 2
60350-A95 CONTROL WIRE 1
60350-A96 NUT M20 1
60350-A97 CONTROL HANDLE LEVER 1
60350-A98 NUT M16 1
60350-A99 TRIGGER SWITCH HANDLE 1
60350-A100 OIL GAUGE 1
60350-A101 GASKET 1
60350-A102 OIL RING 5 X 55 2
60350-A103 CASTING PLUG 1
60350-A104 CAP SCREW M6 X 20 3
60350-A105 NUT M10 1
60350-A106 SET SCREW M10 X 35 1
60350-A107 OIL SEAL 1
60350-A108 WORKPIECE STOP SUPPORT 1
60350-A110 WORKPIECE STOP BRACKET 1
60350-A111 UPPER ROD 1
60350-A112 LOWER ROD 1
60350-A113 LOCK KNOB 1
60350-A114 NYLOCK NUT 2
60350-A115 SHAFT (RIGHT) 1
60350-A116 SHAFT (LEFT) 1
60350-A117 BUSHING 1
60350-A118 HEX HEAD BOLT 2
60350-A119 NUT 2
60350-A120 CONTROL BOX ARM 1
60350-A121 DIGITAL DISPLAY 1
60350-A122 SPEED CONTROL KNOB 1
60350-A123 CONTROL COVER 1
60350-A124 PUMP SELECTION SWITCH 1
60350-A125 EMERGENCY SWITCH 1
60350-A126 START BUTTON 1
60350-A127 STOP BUTTON 1
60350-A128 SCREW 4
60350-A129 CAP SCREW 2
60350-A130 SUPPORT PLATE 1
60350-A131 TRANSMISSION WIRE 1
60350-A132 SPLASH GUARD PLATE 1

BLADE SPECIFICATIONS

A (blade diameter): 14”/350 mm
B (distance between pinhole centres): 63 mm
C (flange diameter): 89 mm
D (center hole/bore diameter): 32 mm
E (number of pin holes): can be 2 or 4
F (hole diameter): 11 mm

DIAGRAM & PARTS LIST CABINET AND PUMP

IMPORTANT: When ordering replacement parts, always give the model number, serial number of the machine and part number. Also a brief description of each item and quantity desired.

PART # DESCRIPTION SPECIFICATIONS QTY