GENERAL 75-155 Drill Press Instruction Manual

GENERAL 75-155 Drill Press

Specifications

• Models: #75-155, #75-165, #75-510
• Adjustable spindle tension return spring
• Built-in laser pointer
• Sturdy design with cast-iron head, base, and table
• High-quality bearings for smooth, vibration-free operation
• Simple hand lever controlled mechanical variable speed from 280 to 2100 rpm
• Digital spindle speed display
• Industrial-quality 120 V motor
• Chuck with key
• Easy to use see-through flip-up chuck guard included
• Crank-operated rack and pinion table height adjustment

Product Usage Instructions

Safety Precautions

• Do not operate the drill press when tired, distracted, or under the effects of drugs, alcohol, or any medication that impairs reflexes or alertness.
• The work area should be well lit, clean, and free of debris.
• Keep children and visitors at a safe distance when the drill press is in operation; do not permit them to operate the drill press.
• Childproof and tamper-proof your shop and all machinery with locks, master electrical switches, and switch keys to prevent unauthorized or unsupervised use.
• Stay alert! Give your work your undivided attention. Even a momentary distraction can lead to serious injury.
• Fine particulate dust is a carcinogen that can be hazardous to health. Work in a well-ventilated area and whenever possible, use a dust collector and wear eye, ear, and respiratory protection devices.
• Do not wear loose clothing, gloves, bracelets, necklaces, or other jewelry while the drill press is in operation.
• Be sure that adjusting wrenches, tools, drinks, and other clutter are removed from the machine and/or the table surface before operating.
• Keep hands well away from the drill bit and all moving parts. Use a hold-down or clamp to secure the stock, and use a brush, not hands, to clear away chips and dust.
• Always disconnect the tool from the power source before servicing or changing accessories such as bits or before performing any maintenance, cleaning, or if the machine will be left unattended.
• Make sure that the switch is in the OFF position before plugging in the power cord.
• Never stand on machinery. Serious injury could result if the tool is tipped over or if the drill bit is unintentionally contacted.
• Keep guards in place and in working order. If a guard must be removed for maintenance or cleaning, be sure it is properly re-attached before using the tool again.
• Avoid working from awkward or off-balance positions. Do not overreach and keep both feet on the floor.
• Never leave the machine unattended while it is running or with the power on.
• Use of parts and accessories NOT recommended by the manufacturer may result in equipment malfunction or risk of injury.
• Make sure the tool is properly grounded. If equipped with a 3-prong plug, it should be used.

SETUP & OPERATION MANUAL

FEATURES

• Adjustable spindle tension return spring.
• Built-in laser pointer.
• Sturdy design with cast-iron head, base, and table.
• High-quality bearings for smooth, vibration-free operation.
• Simple hand lever controlled mechanical variable speed from 280 to 2100 rpm.
• Digital spindle speed display. Industrial-quality 120 V motor. Chuck with key.
• Easy to use see-through flip-up chuck guard included.
• Crank-operated rack and pinion table height-adjustment.

SPECIFICATIONS

• Swing

  • 15″ (390 mm) – # 75-155
  • 17″ (430 mm) – # 75-165
  • 20″ (515 mm) – # 75-510

• Drilling capacity / Chuck size

  • 3/4″ (20 mm) / 5/8″ (16 mm) – # 75-155
  • 1 1/8″ (28 mm) / 5/8″ (16 mm) – # 75-165
  • 1 1/4″ (32 mm) / 3/4″ (20 mm) – # 75-510

• Spindle travel

  • 3 1/8″ (80 mm) – # 75-155/165
  • 4 3/4″ (120 mm) – # 75-510

• Spindle distance to table / to base

  • 29 3/8″ (745 mm) / 48 1/2″ (1230 mm) – # 75-155 29″ (735 mm) / 48 5/8″ (1235 mm) – # 75-165 27 3/4″ (705 mm) / 46 7/8″ (1190 mm) – # 75-510

• Table size
  (Diameter) 12 3/8″ (315 mm) – # 75-155

  • 13 3/16″ x 13 3/16″ (335 x 335 mm) – # 75-165 18 3/4″ x 16 3/4″ (475 x 425 mm) – # 75-510

• Column diameter

  • 2 3/4″ (70 mm) – # 75-155
  • 3 1/8″ (80 mm) – # 75-165
  • 3 5/8″ (92 mm) – # 75-510

• Spindle speeds

  • (Variable speed) – 280 to 2100 rpm

• Spindle taper

  • MT 2 – # 75-155 / MT 3 – # 75-165/510

• Overall height

  • 63 3/8″ (1610 mm) – # 75-155
  • 64 3/8″ (1635 mm) – # 75-165
  • 67″ (1700 mm) – # 75-510

• Base size

  • 17″ x 10 1/2″ (430 x 265 mm) – # 75-155
  • 20 1/4″ x 12″ (515 x 303 mm) – # 75-165
  • 23 5/8″ x 15 3/4″ (600 x 400 mm) – # 75-510

• Motor

  • 1/2 HP, 120 V, 5A – # 75-155
  • 3/4 HP, 120 V, 6,5A – # 75-165
  • 1 HP, 120 V, 10A – # 75-510

• Weight

  • 136 lbs (62 kg) – # 75-155
  • 161 lbs (73 kg) – # 75-165
  • 284 lbs (129 kg) – # 75-510

GENERAL® INTERNATIONAL

8360 Champ-d’Eau, Montreal (Quebec) Canada H1P 1Y3
Telephone 514-326-1161 • Fax 514-326-5555 • www.general.ca

THANK YOU for choosing this General® International model 75-155, 75-165
or 75-510 drill press. This drill press has been carefully tested and inspected before shipment and if properly used and maintained, will provide you with years of reliable service. For your safety, as well as to ensure optimum performance and trouble-free operation, and to get the most from your investment, please take the time to read this manual before assembling, installing and operating the unit.
The manual’s purpose is to familiarize you with the safe operation, basic function, and features of this drill press as well as the set-up, maintenance and identification of its parts and components. This manual is not intended as a substitute for formal woodworking/metalworking instruction, nor to offer the user instruction in the craft of woodworking/metalworking. If you are not sure about the safety of performing a certain operation or procedure, do not proceed until you can confirm, from knowledgeable and qualified sources, that it is safe to do so.

Once you’ve read through these instructions, keep this manual handy for future reference.

DISCLAIMER: The information and specifications in this manual pertain to the unit as it was supplied from the factory at the time of printing. Because we are committed to making constant improvements, General® International reserves the right to make changes to components, parts or features of this unit as deemed necessary, without prior notice and without obligation to install any such changes on previously delivered units. Reasonable care is taken at the factory to ensure that the specifications and information in this manual corresponds with that of the unit with which it was supplied. However, special orders and “after factory” modifications may render some or all information in this manual inapplicable to your machine. Further, as several generations of this model of drill press and several versions of this manual may be in circulation, if you own an earlier or later version of this unit, this manual may not depict your unit exactly. If you have any doubts or questions contact your retailer or our support line with the model and serial number of your unit for clarification.

GENERAL® INTERNATIONAL WARRANTY

All component parts of General® International and Excalibur by General International® products are carefully inspected during all stages of production and each unit is thoroughly inspected upon completion of assembly.

Limited Lifetime Warranty
Because of our commitment to quality and customer satisfaction, General® International agrees to repair or replace any part or component which upon examination, proves to be defective in either workmanship or material to the original purchaser for the life of the tool. However, the Limited Lifetime Warranty does not cover any product used for professional or commercial production purposes nor for industrial or educational applications. Such cases are covered by our Standard 2-year Limited Warranty only. The Limited Lifetime Warranty is also subject to the “Conditions and Exceptions” as listed below.

Standard 2-Year Limited Warranty
All products not covered by our lifetime warranty including products used in commercial, industrial and educational applications are warranted for a period of 2 years (24 months) from the date of purchase. General® International agrees to repair or replace any part or component which upon examination, proves to be defective in either workmanship or material to the original purchaser during this 2-year warranty period, subject to the “conditions and exceptions” as listed below.

To file a Claim
To file a claim under our Standard 2-year Limited Warranty or under our Limited Lifetime Warranty, all defective parts, components or machinery must be returned freight or postage prepaid to General® International, or to a nearby distributor, repair center or other location designated by General® International. For further details call our service department at 1-888-949-1161 or your local distributor for assistance when filing your claim.
Along with the return of the product being claimed for warranty, a copy of the original proof of purchase and a “letter of claim” must be included (a warranty claim form can also be used and can be obtained, upon request, from General® International or an authorized distributor) clearly stating the model and serial number of the unit (if applicable) and including an explanation of the complaint or presumed defect in material or workmanship.

CONDITIONS AND EXCEPTIONS
This coverage is extended to the original purchaser only. Prior warranty registration is not required but documented proof of purchase i.e. a copy of original sales invoice or receipt showing the date and location of the purchase as well as the purchase price paid, must be provided at the time of claim.
Warranty does not include failures, breakage or defects deemed after inspection by General® International to have been directly or indirectly caused by or resulting from; improper use, or lack of or improper maintenance, misuse or abuse, negligence, accidents, damage in handling or transport, or normal wear and tear of any generally considered consumable parts or components.
Repairs made without the written consent of General® International will void all warranty.

RULES FOR SAFE OPERATION

To help ensure safe operation, please take a moment to learn the machine’s applications and limitations, as well as potential hazards. General® International disclaims any real or implied warranty and hold itself harmless for any injury that may result from the improper use of it’s equipment.

1. Do not operate the drill press when tired, distracted, or under the effects of drugs, alcohol or any medication that impairs reflexes or alertness.
2. The work area should be well lit, clean and free of debris.
3. Keep children and visitors at a safe distance when the drill press is in operation; do not permit them to operate the drill press.
4. Childproof and tamper proof your shop and all machinery with locks, master electrical switches and switch keys, to prevent unauthorized or unsupervised use.
5. Stay alert! Give your work your undivided attention. Even a momentary distraction can lead to serious injury.
6. Fine particulate dust is a carcinogen that can be hazardous to health. Work in a well-ventilated area and whenever possible use a dust collector and wear eye, ear and respiratory protection devices.
7. Do not wear loose clothing, gloves, bracelets, necklaces or other jewelry while the drill press is in operation.
8. Be sure that adjusting wrenches, tools, drinks and other clutter are removed from the machine and/or the table surface before operating.
9. Keep hands well away from the drill bit and all moving parts. Use a hold-down or clamp to se-cure the stock, and use a brush, not hands, to clear away chips and dust.
10. Be sure that the drill bit is securely installed in the chuck before operation.
11. Be sure the drill bit has gained full operating speed before beginning to drill. Always use a clean, properly sharpened bit. Dirty or dull bits are unsafe and can lead to accidents. Use suitable work piece support if the work piece does not have a flat surface.
12. Do not push or force the bit into the stock. The drill will perform better and more safely when working at the rate feed for which it was designed.
13. Avoid working from awkward or off balance positions. Do not overreach and keep both feet on floor.
14. Keep guards in place and in working order. If a guard must be removed for maintenance or cleaning be sure it is properly re-attached before using the tool again.
15. Never leave the machine unattended while it is running or with the power on.
16. Use of parts and accessories NOT recommended by GENERAL® INTERNATIONAL may result in equipment malfunction or risk of injury.
17. Never stand on machinery. Serious injury could result if the tool is tipped over or if the drill bit is unintentionally contacted.
18. Always disconnect the tool from the power source before servicing or changing accessories such as bits, or before performing any maintenance, cleaning, or if the machine will be left unattended.
19. Make sure that the switch is in the “OFF” position before plugging in the power cord.
20. Make sure the tool is properly grounded. If equipped with a 3-prong plug, it should be used with a three-pole receptacle. Never remove the thir prd ong.
21. Do not use this drill press for other than its intended use. If used for other purposes, GENERAL® INTERNATIONAL disclaims any real implied warranty and holds itvself harmless for any injury, which may result from that use.

ELECTRICAL REQUIREMENTS

BEFORE CONNECTING THE MACHINE TO THE POWER SOURCE, VERIFY THAT THE VOLTAGE OF YOUR POWER SUPPLY CORRESPONDS WITH THE VOLTAGE SPECIFIED ON THE MOTOR I.D. NAMEPLATE. A POWER SOURCE WITH GREATER VOLTAGE THAN NEEDED CAN RESULT IN SERIOUS INJURY TO THE USER AS WELL AS DAMAGE TO THE MACHINE. IF IN DOUBT, CONTACT A QUALIFIED ELECTRICIAN BEFORE CONNECTING TO THE POWER SOURCE.
THIS TOOL IS FOR INDOOR USE ONLY. DO NOT EXPOSE TO RAIN OR USE IN WET OR DAMP LOCATIONS.

GROUNDING INSTRUCTIONS

In the event of an electrical malfunction or short circuit, grounding reduces the risk of electric shock. The motor of this machine is wired for 120 V single phase operation and is equipped with a 3-conductor cord and a 3-prong grounding plug A to fit a grounded type receptacle B. Do not remove the 3rd prong (grounding pin) to make it fit into an old 2-hole wall socket or extension cord. If an adaptor plug is used C, it must be attached to the metal screw of the receptacle.
Note: The use of an adaptor plug is illegal in some areas. Check your local codes. If you have any doubts or if the supplied plug does not correspond to your electrical outlet, consult a qualified electrician before proceeding.

CIRCUIT CAPACITY

Make sure that the wires in your circuit are capable of handling the amperage draw from your machine, as well as any other machines that could be operating on the same circuit. If you are unsure, consult a qualified electri-cian. If the circuit breaker trips or the fuse blows regularly, your machine may be operating on a circuit that is close to its amperage draw capacity. However, if an unusual amperage draw does not exist and a power failure still occurs, contact a qualified technician or our service department.

EXTENSION CORDS
If you find it necessary to use an extension cord with your machine, use only 3-wire extension cords that have 3-prong grounding plug and a matching 3-pole receptacle that accepts the tool’s plug. Repair or replace a damaged extension cord or plug immediately.
Make sure the cord rating is suitable for the amperage listed on the motor I.D. plate. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The accompanying chart shows the correct size extension cord to be used based on cord length and motor I.D. plate amp rating. If in doubt, use the next heavier gauge. The smaller the number, the heavier the gauge.

IDENTIFICATION OF MAIN PARTS AND COMPONENTS

• A. BASE
• B. COLUMN
• C. TABLE PIVOT LOCK LEVER*
• D. TABLE
• E. FLIP-UP CHUCK GUARD
• F. LASER POINTER SWITCH
• G. DIGITAL SPEED DISPLAY
• H. SWITCH
• I. PULLEY COVER
• J. MOTOR
• K. FEED HANDLE
• L. TABLE CRANK HANDLE
• M. RACK

UNPACKING

Carefully unpack and remove the unit and its components from the box and check for missing or damaged items as per the list of contents below.

ADDITIONAL REQUIREMENTS FOR SET UP

• A. EXTRA PERSON FOR HELP WITH LIFTING
• B. 9, 16 & 24 MM OPEN WRENCHES
• C. PHILLIPS SCREWDRIVER

CLEANING

The protective coating on the machine prevents rust from forming during shipping and storage. Remove it by rubbing with a rag dipped in kerosene, mineral spir-its or paint thinner. (Dispose of potentially flammable solvent- soaked rags according to manufacturer’s safe-ty recommendations).
A putty knife, held flat to avoid scratching the surface, may also be used to scrape off the coating followed by clean-up with solvent. Avoid rubbing the machine’s painted surfaces, as many solvent-based products will remove paint.
To prevent rust, apply a light coating of paste wax or use regular applications of any after-market surface protectant or rust inhibitor.

PLACEMENT WITHIN THE SHOP / SAFETY ZONE

THIS DRILL PRESS MODEL (1) 75-155, (2) 75-165 OR (3) 75-510 IS HEAVY. DO NOT OVER-EXERT. A HOIST OR FORK-LIFT WITH STRAPS SHOULD BE USED TO LIFT THIS MACHINE. TO LIMIT THE RISK OF SERIOUS INJURY OR DAMAGE TO THE MACHINE, ANY EQUIPMENT USED TO LIFT THIS MACHINE SHOULD HAVE A RATED CAPACITY IN EXCESS OF THE MACHINE.

PLACEMENT WITHIN THE SHOP

This machine should be installed and operated only on a solid, flat and stable floor that is able to support the weight of the machine 136 lbs (1), 161 lbs (2) or 284 lbs (3) and the operator.
Using the dimensions shown as a guideline, plan for placement within your shop that will allow the operator to work unencumbered and unobstructed by foot traffic (either passing shop visitors or other shop workers) or other tools or machinery.

ESTABLISHING A SAFETY ZONE
For shops with frequent visitors or multiple operators, it is advisable to establish a safety zone around shop machinery.
A clearly defined “no-go” zone on the floor around each machine can help avoid accidents that could cause injury to either the operator or the shop visitor.
It is advisable to take a few moments to either paint (using non-slip paint) or using tape, define on the floor the limits or perimeter of each machines safety zone.
Take steps to ensure that all operators and shop visitors are aware that these areas are off limits whenever a machine is running for everyone but the individual operating the unit.

ASSEMBLY INSTRUCTIONS

BEFORE ASSEMBLING, MAKE SURE THAT THE SWITCH IS IN THE “OFF” POSITION AND THAT THE POWER CORD IS UNPLUGGED. DO NOT PLUG IN OR TURN ON THE MACHINE UNTIL YOU HAVE COMPLETED THE ASSEMBLY AND INSTALLATION STEPS DESCRIBED IN THIS SECTION OF THE MANUAL.

INSTALLING THE COLUMN ON THE BASE

1. Set the base on a flat and stable surface, and then install the column on the base.
   

2. Align the mounting holes in the column with the corresponding holes in the base.

3.  Tighten the four bolts by hand A few turns.
   

4. Then secure the bolts using a 16 mm wrench.

INSTALLING THE HEAD STOCK ON THE COLUMN

THE HEAD STOCK IS HEAVY. DO NOT OVER-EXERT. THE HELP OF AN ASSISTANT WILL BE NEEDED FOR THE FOLLOWING STEP. DO NOT GRIP THE HEAD STOCK BY THE PULLEY COVER WHEN LIFTING.

1. Lift the head stock and place its opening above the column.
   

2.  Slide the head stock opening onto the column.

3. Center the head stock with the column and the table.
   

4. Secure the head stock to the column by tightening screws A & B using a 5 mm Allen key.

INSTALLING THE TABLE (75-155/165 ONLY)

1. Make sure that arbor C is to the right and the table bracket is centered on the column. Turn the bracket if needed as shown.
   

2. Hold the arm against the bracket aligning the mounting holes as shown.

3. Tighten bolt D hand tight for now.
   

4. Turn the arm counterclockwise until the zero point of the table bracket and the arm are aligned as shown E.

5. Tighten the arm’s mounting bolt using a 24 mm
   

6. Insert the table into the arm mount as shown. wrench.

7. Lock the table in place by turning lever A clockwise.
   

8. Slide handle B onto the arbor C as shown D.

9. Tighten the set screw E using a 4 mm Allen key.
   

10. Lock the table in position by tightening the lever F as shown.

MAKE SURE THE MACHINE HAS BEEN TURNED OFF AND UNPLUGGED FROM THE POWER SOURCE BEFORE PERFORMING ANY MAINTENANCE OR ADJUSTMENTS.

INSTALLING THE TABLE (MODEL 75-510 ONLY)

1. Insert the threaded centering pin A into the smallest hole of the table bracket as shown
   

2. Align the smallest mounting hole in the table with the pin.

3. Slide the table onto the pin.
   

4. While an assistant holds the table in position, insert the bolt B into the large mounting hole.

5. Tighten the bolt with a wrench.
   

6. Thread nut C onto the centering pin and tighten using a 13 mm wrench.
   Note : To install the table crank handle, follow steps 8 to 9 in the previous section.

INSTALLING THE CHUCK GUARD

1. Slide the chuck guard onto its support as shown A
   

2. Tighten the chuck guard using a phillips screwdriver.

INSTALLING THE DOWNFEED HANDLES

1. Thread the three downfeed handles into their
   

2. Tighten each handle using a 9 mm wrench. mounting holes located in the support B

INSTALLING THE SPEED CONTROL LEVER

1. Thread the handle into its mounting hole located
   

2. Tighten the handle using a 9 mm wrench. in the bracket C.

INSTALLING THE CHUCK

1. Lift the chuck guard as shown.
   

2. Clean inside the chuck with a dry cloth until all grease or lubricant is removed.

3. Fit the arbor into the chuck as shown.
   

4. Make sure the arbor is inserted all the way into the chuck.

5. Slide the arbor into the quill assembly as shown.
   

6. Using the feed handles, lower the chuck against a piece of wood on the table to pressfit it into the quill.

MAKE SURE THE MACHINE HAS BEEN TURNED OFF AND UNPLUGGED FROM THE POWER SOURCE BEFORE PERFORMING ANY MAINTENANCE OR ADJUSTMENTS.

REMOVING THE CHUCK

1. Using feed handle, lower the quill assembly A. Insert the drift key B all the way into the quill assembly C.
   

2. While holding onto the chuck, tap gently on the key with a hammer or rubber mallet to loosen and remove the arbor and chuck.
   Note: It may be necessary to rotate the quill in order to be able to get the tool all the way through D.

INSTALLING A DRILL BIT

1. Open the chuck by turning the key E counterclockwise until you can insert a drill bit F.
2. Secure the drill bit in the chuck by turning the key clockwise.

BASIC ADJUSTMENTS & CONTROLS

TO REDUCE THE RISK OF SHOCK OR FIRE DO NOT OPERATE THE UNIT WITH A DAMAGED POWER CORD OR PLUG. RE-PLACE DAMAGED CORD OR PLUG IMMEDIATELY. TO AVOID UNEXPECTED OR UNINTENTIONAL START-UP, MAKE SURE THE POWER SWITCH IS IN THE OFF POSITION BEFORE CONNECTING TO A POWER SOURCE.

CONNECTING TO A POWER SOURCE

• Once the assembly steps have been completed, plug the power cord into an appropriate outlet.
• Refer back to the section entitled “Electrical Require-ments” and make sure all requirements and grounding instructions are followed.
• When operations have been completed unplug the machine from the power source.

MAKE SURE THE MACHINE HAS BEEN TURNED OFF AND UNPLUGGED FROM THE POWER SOURCE BEFORE PERFORM-ING ANY MAINTENANCE OR ADJUSTMENTS.

ON/OFF POWER SWITCH

• This drill is equipped with a forced opening line interrupter switch located on the front which requires machine restart in case of power failure or circuit interruption.
• To start the machine, pull up the switch cover and press the start button “I”, A.
• To stop the machine, press directly on the switch cover B.
• To turn on the laser pointer, set the swtich C in the “I” position. To turn off the laser pointer, set the switch in the “O” position.

ADJUSTING THE CHUCK GUARD HEIGHT

1. Loosen the wing nuts D.
   

2.  Position the shield at the desired height, then retighten the wing nuts.

ADJUSTING THE DEPTH STOP

This drill is equipped with an adjustable depth stop to allow repetitive drilling to a set depth. To set the depth stop:

1. Loosen knob E counterclockwise as shown.
   

2. Turn the depth stop to the desired drilling depth F, then retighten the knob.

MAKE SURE THE MACHINE HAS BEEN TURNED OFF AND UNPLUGGED FROM THE POWER SOURCE BEFORE PERFORM-ING ANY MAINTENANCE OR ADJUSTMENTS.

TABLE SWING ADJUSTMENT

1. Loosen the column lock handle as shown.
   

2. Swing the table arm bracket and the table to the desired position, then retighten the column lock handle.
   Note : When working with taller work pieces swing the ta-ble 180° out of the way and use the base as a table.

PIVOTING THE TABLE (MODEL 75-155 & 75-165 ONLY)

1. Loosen the pivot lock handle as shown.
   

2. Turn the table to the desired position, and then re- tighten the pivot lock handle.

ADJUSTING TABLE HEIGHT

1. Loosen the column lock handle as shown.
   

2. Turn the crank handle as shown until the table is at the desired height, then retighten the column lock handle.

MAKE SURE THE MACHINE HAS BEEN TURNED OFF AND UNPLUGGED FROM THE POWER SOURCE BEFORE PERFORM-ING ANY MAINTENANCE OR ADJUSTMENTS.

TABLE TILT ADJUSTMENT
Note : For the model 75-510 remove the threaded centering pin under the table before completing the following steps.

1. Loosen nut A
   

2. Tilt the table to the desired angle, and then retighten the nut A.

DRILL SPEED ADJUSTMENT

This machine is equipped with a mechanical vari-able speed drive pulley system that allows the user to change the spindle speed while the machine is in op- eration.
This system is considered more efficient and conve-nient than models that require a complete shut-down and then a more complicated change of belts on a multi-pulley system.
To change speeds the user simply turns on the ma-chine and then turns the speed control lever in the ap-propriate direction until the desired speed appears on the digital speed display.

GUIDELINES FOR SELECTING SPEEDS BASED ON BIT SIZE AND BIT MATERIAL

OPERATING INSTRUCTIONS

CHECKLIST BEFORE STARTING

VERIFY ALL CHECK POINTS BEFORE STARTING. FAILURE TO COMPLY CAN RESULT IN SERIOUS INJURIES.

• Make sure the pulley cover is closed.
• Check that the chuck is installed properly.
• Make sure the chuck guard is securely installed and closed properly.
• When turning the machine “ON” be aware that the shaft will rotate freely.
• When the drill press is running check to see if it runs without vibration or shaking.
• Make sure the table bracket moves up and down smoothly.
• Make sure the spindle shaft turns smoothly.

DRILLING STEP-BY-STEP

1. Lift the chuck guard as shown and install a drill bit suitable for the type of material to drill.

2. Flip the chuck guard down in place as shown.

3. Secure the workpiece in a vise (optional).
   

4. For precision drilling use the laser pointer A to locate the drilling point on the workpiece.

5. Turn ON the machine and adjust the speed.
   

6. Use the downfeed handles to lower the bit into the workpiece.

MAINTENANCE

BELT REPLACEMENT

Inspect the belts afler every 100 hours of use. Belts that show visible signs of wear such as cracks or fraying at the edges should be replaced immediately.

Note : To replace belt A, remove belt B first.

1. Unplug the machine, and open the pulley cover as shown.

2. Pull on the belt as shown to spread the spring- mounted pulley flanges.

3. Slip a portion of the belt off and turn the pulley by hand until the belt comes off the pulley completely.

4. To install a new belt, spread the lower flange on the motor pulley using a pry-bar.
   Note: Use gentle pressure to not damage the pulley.

5. Hold the flange open while slipping the new belt onto the open pulley.

6. Pull back on the belt to make sure it is seated prop erly on the pulley.

7. Slide the opposite end of the belt onto the other pul-ley, then turn the pulley until the belt snaps into place.

MAKE SURE THE MACHINE HAS BEEN TURNED OFF AND UNPLUGGED FROM THE POWER SOURCE BEFORE PERFORM-ING ANY MAINTENANCE OR ADJUSTMENTS.

LUBRICATION

Periodically lubricate all sliding or moving parts including the column, rack and the quill shown (use any all purpose grease, available at any hardware store).
Note: Bearings in the quill and the V-belt pulleys are sealed, permanently lubricated and should require no fur-ther maintenance.

RECOMMENDED OPTIONAL ACCESSORIES

DIAGRAM 75-155

PARTS LIST 75-155

IMPORTANT : When ordering replacement parts, always give the model number, serial number of the machine and part number. Also a brief description of each item and quantity desired.

| PARTS LIST

IMPORTANT: When ordering replacement parts, always give the model number, serial number of the machine and part number. Also a brief description of each item and quantity desired.

|
---|---|---

PART #

|

REFERENCE

|

DESCRIPTION

|

SPECIFICATIONS

|

QTY

|
75155-01| 13301001A| BASE| | 1|
75155-02| 16101002| SUPPPORT COLUMN| | 1|
75155-03| | SET SCREW| M10 X 12| 3|
75155-04| | BOLT| M10 X 30| 4|
75155-05| 16101010| RACK| | 1|
75155-06| 16101003| COLUMN| | 1|
75155-07| | SET SCREW| M6 X 10| 1|
75155-08| 16101011D| RACK RETENTION RING| | 1|
75155-09| 16101007A| PIN| | 1|
75155-10| 16101006| HELICAL GEAR| | 1|
75155-11| 16101008| WORM GEAR| | 1|
75155-12| | SET SCREW| M8 X 10| 1|
75155-13| 13201009B| HANDLE BRACKET| | 1|
75155-14| 13201009B-2| HANDLE| | 1|
75155-15| | HEX HEAD BOLT| M16 X 35| 1|
75155-16| 16101013A| LOCK HANDLE| | 1|
75155-17| 16101004| TABLE BRACKET| | 1|
75155-18| 16101005| TABLE ARM| | 1|
75155-19| 16101014A| TABLE| | 1|
75155-20| 16101012A| LOCK HANDLE| | 1|
75155-21| 20104011| KNOB| | 3|
75155-22| 16104005A| ROD| | 3|
75155-23| 16104001| HANDLE BRACKET| | 1|
75155-24| | PIN| 5 X 16| 1|
75155-25| 16104003| DEPTH STOP RING| | 1|
75155-26| 16104004| LOCK BLOCK| | 1|
75155-27| 13102005B| DEPTH LOCK SCREW| | 1|
75155-28| 16104002| SHAFT PINION| | 1|
75155-29| 16103005| NYLOCK NUT| | 1|
75155-30| 16103004| RETENTION RING| | 1|
75155-31| 16103003| WASHER| | 1|
75155-32| | BEARING| 6203| 1|
75155-33| 16103006| QUILL GASKET| | 1|
75155-34| 16103002| QUILL ASSEMBLY| | 1|
75155-35| 16103008| DRIFT KEY| | 1|
75155-36| | BEARING| 8204| 1|
75155-37| 16103001| SPINDLE| | 1|
75155-38| 16103007| ARBOR| | 1|
75155-39| 16103009G| CHUCK| | 1|
75155-40| 16103009G-1| CHUCK KEY| | 1|
75155-41| 16108002| CHUCK GUARD| | 1|
75155-42| 13302026| LASER POINTER| | 2|
75155-43| | SET SCREW| M6 X 8| 2|
75155-44| 16104010| STOP PIN| | 1|
75155-45| | PIN| 6 X 25| 2|
75155-46| W16102001| HEAD STOCK| | 1|
75155-47| | PIN| 5 X 35| 2|
75155-48| | HEX HEAD BOLT| M8 X 25| 4|
75155-49| | WASHER| | 4|
75155-50| W16102007| MOTOR PLATE| | 1|
75155-51| | LOCK WASHER| | 3|
75155-52| | HEX HEAD BOLT| M8 X 20| 3|
75155-53| | WASHER| | 4|
75155-54| | NUT| M8| 4|
75155-55| YLL7124-W06| MOTOR| | 1|
75155-56| | KEY| 5 X 45| 1|
75155-57| W16205005-4| LOCK WASHER| | 1|
75155-58| W16205005-3| MOTOR PULLEY SPRING| | 1|
75155-59| W16205005-2| MOVEABLE PULLEY FLANGE| | 1|
75155-60| W16205005-1| FIXED PULLEY FLANGE| | 1|
75155-61| | RETENTION RING| | 1|
75155-62| W16105004-5| TENSIONING PULLEY BASE| | 1|
75155-63| | PIN| 3 X 8| 1|
75155-64| W16205004-2| SLEEVE| | 1|
75155-65| | HEX HEAD BOLT| M8 X 12| 1|
75155-66| | LOCK WASHER| | 1|
75155-67| | BEARING| | 1|
| | | | |
24| | | | | | |

PARTS LIST 75-155

PARTS LIST

IMPORTANT: When ordering replacement parts, always give the model number, serial number of the machine and part number. Also a brief description of each item and quantity desired.

|
---|---
| PART #| REFERENCE| DESCRIPTION| SPECIFICATIONS| QTY| |
| 75155-68| | RETENTION RING| | 1| |
| 75155-69| W16205007-2| TENSIONING PULLEY SHAFT| | 1| |
| 75155-70| | PIN| 5 X 32| 2| |
| 75155-71| | RETENTION RING| | 1| |
| 75155-72| | BEARING| 61905| 2| |
| 75155-73| W16205007-1| SLEEVE| | 1| |
| 75155-74| | KEY| 5X14| 1| |
| 75155-75| | RETENTION RING| | 1| |
| 75155-76| W16205006-2| TENSIONING PULLEY FLANGE| | 1| |
| 75155-77| W16105010| “V” BELT| 16 X 565| 1| |
| 75155-78| | RETENTION RING| | 2| |
| 75155-79| W16205006-3| TENSIONING PULLEY FLANGE| | 1| |
| 75155-80| W20105010| “V” BELT| 17 X 690| 1| |
| 75155-81| W16205006-1| UPPER TENSIONING PULLEY FLANGE| | 1| |
| 75155-82| | RETENTION RING| | 1| |
| 75155-83| W16205009-4| SPRING STOP SPACER| | 1| |
| 75155-84| W16205009-3| SPRING| | 1| |
| 75155-85| W16205009-2| UPPER PULLEY FLANGE| | 1| |
| 75155-86| W16205009-1| LOWER PULLEY FLANGE| | 1| |
| 75155-87| W16205009-5A| SPEED SENSOR TAB| | 1| |
| 75155-88| | SCREW| M4 X 6| 2| |
| 75155-89| 16102024| RETENTION RING| | 2| |
| 75155-90| | KEY| 5 X 35| 1| |
| 75155-91| W16102022| PULLEY SHAFT| | 1| |
| 75155-92| | BEARING| 6204| 2| |
| 75155-93| 16102023A| SPACER| | 1| |
| 75155-94| W16105000| PULLEY COVER| | 1| |
| 75155-95| 13205010| KNOB| | 1| |
| 75155-96| | SCREW| M6 X 12| 4| |
| 75155-97| | WASHER| | 4| |
| 75155-98| 16102014A| CORD CLAMP| | 1| |
| 75155-99| | SCREW| M5 X 10| 2| |
| 75155-100| 13105009| WASHER| | 4| |
| 75155-101| | NYLOCK NUT| M4| 2| |
| 75155-102| W134A05009| SENSOR BRACKET| | 1| |
| 75155-103| DQ014001100-4| SENSOR| | 1| |
| 75155-104| | CAP SCREW| M2.5 X 5| 1| |
| 75155-105| | SCREW| M4 X 20| 2| |
| 75155-106| W16202027A| GEAR SHAFT| | 1| |
| 75155-107| | KEY| 3 X 8| 1| |
| 75155-108| W13202028B| FLANGE| | 1| |
| 75155-109| | SCREW| M5 X 10| 3| |
| 75155-110| W13202031| HANDLE HOLDER| | 1| |
| 75155-111| | LOCK WASHER| | 1| |
| 75155-112| | NYLOCK NUT| M10| 1| |
| 75155-113| C13104005| ROD| | 1| |
| 75155-114| 13204011| KNOB| | 1| |
| 75155-115| | NUT| M12| 2| |
| 75155-116| 16104008| CAP SPRING| | 1| |
| 75155-117| 16104009| SPRING| | 1| |
| 75155-118| 16104007A| NUT| | 1| |
| 75155-119| 16104006A| SLEEVE| | 1| |
| 75155-120| | NUT| M10| 1| |
| 75155-121| 16102021| NYLOCK NUT| | 1| |
| 75155-122| | SET SCREW| M5 X 6| 2| |
| 75155-123| | SPROCKET WASHER| | 2| |
| 75155-124| | SCREW| ST2.9 X 6.5| 2| |
| 75155-125| DQ010003200| DIGITAL SPEED DISPLAY| | 1| |
| 75155-126| | SCREW| M5 X 16| 3| |
| 75155-127| KCD1| LASER SWITCH| | 1| |
| 75155-128| KJD12| SWITCH| | 1| |
| 75155-129| W16102008A| SWITCH BOX| | 1| |
| 75155-130| | SCREW| ST4.2 X 9.5| 3| |
| 75155-131| DLCKEE3S16| POWER CORD W/PLUG| | 1| |
| 75155-132| | ALLEN KEY| 3 MM| 1| |
| 75155-133| | ALLEN KEY| 4 MM| 1| |
| 75155-134| | ALLEN KEY| 5 MM| 1| |
| | | | | | |
| | | | | | | 25

DIAGRAM 75-165

PARTS LIST 75-165

PARTS LIST

IMPORTANT: When ordering replacement parts, always give the model number, serial number of the machine and part number. Also a brief description of each item and quantity desired.

|
---|---
| PART #| REFERENCE| DESCRIPTION| SPECIFICATIONS| QTY| |
| 75165-01| 16101001B| BASE| | 1| |
| 75165-02| 16201002| SUPPPORT COLUMN| | 1| |
| 75155-03| | SET SCREW| M10 X 12| 3| |
| 75165-04| | BOLT| M10 X 30| 4| |
| 75155-05| 16101010| RACK| | 1| |
| 75165-06| 16201003| COLUMN| | 1| |
| 75155-07| | SET SCREW| M6 X 10| 1| |
| 75165-08| 16201011E| RACK RETENTION RING| | 1| |
| 75155-09| 16101007A| PIN| | 1| |
| 75155-10| 16101006| HELICAL GEAR| | 1| |
| 75155-11| 16101008| WORM GEAR| | 1| |
| 75155-12| | SET SCREW| M8 X 10| 1| |
| 75155-13| 13201009B| HANDLE BRACKET| | 1| |
| 75155-14| 13201009B-2| HANDLE| | 1| |
| 75155-15| | HEX HEAD BOLT| M16 X 35| 1| |
| 75155-16| 16101013A| LOCK HANDLE| | 1| |
| 75165-17| 16201004| TABLE BRACKET| | 1| |
| 75165-18| 16201005| TABLE ARM| | 1| |
| 75165-19| 16201014D| TABLE| | 1| |
| 75155-20| 16101012A| LOCK HANDLE| | 1| |
| 75155-21| 20104011| KNOB| | 3| |
| 75155-22| 16104005A| ROD| | 3| |
| 75155-23| 16104001| HANDLE BRACKET| | 1| |
| 75155-24| | PIN| 5 X 16| 1| |
| 75155-25| 16104003| DEPTH STOP RING| | 1| |
| 75155-26| 16104004| LOCK BLOCK| | 1| |
| 75155-27| 13102005B| DEPTH LOCK SCREW| | 1| |
| 75155-28| 16104002| SHAFT PINION| | 1| |
| 75155-29| 16103005| NYLOCK NUT| | 1| |
| 75155-30| 16103004| RETENTION RING| | 1| |
| 75155-31| 16103003| WASHER| | 1| |
| 75155-32| | BEARING| 6203| 1| |
| 75165-33| 16203006| QUILL GASKET| | 1| |
| 75165-34| 16203002| QUILL ASSEMBLY| | 1| |
| 75155-35| 16103008| DRIFT KEY| | 1| |
| 75165-36| | BEARING| 8206| 1| |
| 75165-37| 16203001A| SPINDLE| | 1| |
| 75165-38| 20103007| ARBOR| | 1| |
| 75155-39| 16103009G| CHUCK| | 1| |
| 75155-40| 16103009G-1| CHUCK KEY| | 1| |
| 75165-41| 20108002| CHUCK GUARD| | 1| |
| 75155-42| 13302026| LASER POINTER| | 2| |
| 75155-43| | SET SCREW| M6 X 8| 2| |
| 75155-44| 16104010| STOP PIN| | 1| |
| 75155-45| | PIN| 6 X 25| 2| |
| 75165-46| W16202001| HEAD STOCK| | 1| |
| 75155-47| | PIN| 5 X 35| 2| |
| 75155-48| | HEX HEAD BOLT| M8 X 25| 4| |
| 75155-49| | WASHER| | 4| |
| 75165-50| W16202007| MOTOR PLATE| | 1| |
| 75155-51| | LOCK WASHER| | 3| |
| 75155-52| | HEX HEAD BOLT| M8 X 20| 3| |
| 75155-53| | WASHER| | 4| |
| 75155-54| | NUT| M8| 4| |
| 75165-55| YLL8014-W03| MOTOR| | 1| |
| 75155-56| | KEY| 5 X 45| 1| |
| 75155-57| W16205005-4| LOCK WASHER| | 1| |
| 75155-58| W16205005-3| MOTOR PULLEY SPRING| | 1| |
| 75155-59| W16205005-2| MOVEABLE PULLEY FLANGE| | 1| |
| 75155-60| W16205005-1| FIXED PULLEY FLANGE| | 1| |
| 75155-61| | RETENTION RING| | 1| |
| 75155-62| W16105004-5| TENSIONING PULLEY BASE| | 1| |
| 75155-63| | PIN| 3 X 8| 1| |
| 75155-64| W16205004-2| SLEEVE| | 1| |
| 75155-65| | HEX HEAD BOLT| M8 X 12| 1| |
| 75155-66| | LOCK WASHER| | 1| |
| 75155-67| | BEARING| | 1| |
| | | | | | |
| | | | | | | 27
| PARTS LIST

IMPORTANT: When ordering replacement parts, always give the model number, serial number of the machine and part number. Also a brief description of each item and quantity desired.

|
---|---|---
PART #| REFERENCE| DESCRIPTION| SPECIFICATIONS| QTY|
75155-68| | RETENTION RING| | 1|
75155-69| W16205007-2| TENSIONING PULLEY SHAFT| | 1|
75155-70| | PIN| 5 X 32| 2|
75155-71| | RETENTION RING| | 1|
75155-72| | BEARING| 61905| 2|
75155-73| W16205007-1| SLEEVE| | 1|
75155-74| | KEY| 5X14| 1|
75155-75| | RETENTION RING| | 1|
75155-76| W16205006-2| TENSIONING PULLEY FLANGE| | 1|
75165-77| W16205010| “V” BELT| 16 X 600| 1|
75155-78| | RETENTION RING| | 2|
75155-79| W16205006-3| TENSIONING PULLEY FLANGE| | 1|
75155-80| W20105010| “V” BELT| 17 X 690| 1|
75155-81| W16205006-1| UPPER TENSIONING PULLEY FLANGE| | 1|
75155-82| | RETENTION RING| | 1|
75155-83| W16205009-4| SPRING STOP SPACER| | 1|
75155-84| W16205009-3| SPRING| | 1|
75155-85| W16205009-2| UPPER PULLEY FLANGE| | 1|
75155-86| W16205009-1| LOWER PULLEY FLANGE| | 1|
75155-87| W16205009-5A| SPEED SENSOR TAB| | 1|
75155-88| | SCREW| M4 X 6| 2|
75165-89| 16202024| RETENTION RING| | 2|
75155-90| | KEY| 5 X 35| 1|
75165-91| W16202022| PULLEY SHAFT| | 1|
75165-92| | BEARING| 6205| 2|
75165-93| 16202023A| SPACER| | 1|
75165-94| W16205000| PULLEY COVER| | 1|
75155-95| 13205010| KNOB| | 1|
75155-96| | SCREW| M6 X 12| 4|
75155-97| | WASHER| | 4|
75155-98| 16102014A| CORD CLAMP| | 1|
75155-99| | SCREW| M5 X 10| 2|
75155-100| 13105009| WASHER| | 4|
75155-101| | NYLOCK NUT| M4| 2|
75155-102| W134A05009| SENSOR BRACKET| | 1|
75155-103| DQ014001100-4| SENSOR| | 1|
75155-104| | CAP SCREW| M2.5 X 5| 1|
75155-105| | SCREW| M4 X 20| 2|
75155-106| W16202027A| GEAR SHAFT| | 1|
75155-107| | KEY| 3 X 8| 1|
75155-108| W13202028B| FLANGE| | 1|
75155-109| | SCREW| M5 X 10| 3|
75155-110| W13202031| HANDLE HOLDER| | 1|
75155-111| | LOCK WASHER| | 1|
75155-112| | NYLOCK NUT| M10| 1|
75155-113| C13104005| ROD| | 1|
75155-114| 13204011| KNOB| | 1|
75155-115| | NUT| M12| 2|
75155-116| 16104008| CAP SPRING| | 1|
75155-117| 16104009| SPRING| | 1|
75155-118| 16104007A| NUT| | 1|
75155-119| 16104006A| SLEEVE| | 1|
75155-120| | NUT| M10| 1|
75155-121| 16102021| NYLOCK NUT| | 1|
75155-122| | SET SCREW| M5 X 6| 2|
75155-123| | SPROCKET WASHER| | 2|
75155-124| | SCREW| ST2.9 X 6.5| 2|
75155-125| DQ010003200| DIGITAL SPEED DISPLAY| | 1|
75155-126| | SCREW| M5 X 16| 3|
75155-127| KCD1| LASER SWITCH| | 1|
75155-128| KJD12| SWITCH| | 1|
75165-129| W16202008A| SWITCH BOX| | 1|
75155-130| | SCREW| ST4.2 X 9.5| 3|
75155-131| DLCKEE3S16| POWER CORD W/PLUG| | 1|
75155-132| | ALLEN KEY| 3 MM| 1|
75155-133| | ALLEN KEY| 4 MM| 1|
75155-134| | ALLEN KEY| 5 MM| 1|
| | | | |
28| | | | | | |

DIAGRA

| PARTS LIST

IMPORTANT: When ordering replacement parts, always give the model number, serial number of the machine and part number. Also a brief description of each item and quantity desired.

|
---|---|---
PART #| REFERENCE| DESCRIPTION #| SPECIFICATION| QTY|
75510-01| 20101001A| BASE| | 1|
75510-02| 20101002| SUPPPORT COLUMN| | 1|
75510-03| | SET SCREW| M10 X 12| 3|
75510-04| | BOLT| M12 X 40| 4|
75510-05| 20101010| RACK| | 1|
75510-06| 20101003| COLUMN| | 1|
75510-07| 20101009-2-3-4| HANDLE| | 1|
75510-08| 20101009-1| HANDLE BRACKET| | 1|
75510-09| | SET SCREW| M6 X 10| 2|
75510-10| 20101008| WORM GEAR| | 1|
75510-11| 16101006| HELICAL GEAR| | 1|
75510-12| 16101007| PIN-GEAR| | 1|
75510-13| 20101011A| RACK RETENTION RING| | 1|
75510-14| 16101012A| COLUMN LOCK HANDLE| | 1|
75510-15| 20101004| TABLE SUPPORT| | 1|
75510-16| 20101014E| TABLE| | 1|
75510-17| | HEX HEAD BOLT| M20 X 50| 1|
75510-18| 20101015| THREADED ROD| | 1|
75510-19| | LOCK WASHER| | 1|
75510-20| 20104011| KNOB| | 3|
75510-21| 20104005A| ROD| | 3|
75510-22| 16104001| HANDLE BRACKET| | 1|
75510-23| | PIN| 5 X 16| 1|
75510-24| 16104003| DEPTH STOP RING| | 1|
75510-25| 16104004| LOCK BLOCK| | 1|
75510-26| 16104012| DEPTH LOCK SCREW| | 1|
75510-27| 20104002A| SHAFT PINION| | 1|
75510-28| 20103005| NYLOCK NUT| | 1|
75510-29| 20103004| RETENTION RING| | 1|
75510-30| 20103003| WASHER| | 1|
75510-31| | BEARING| 6204| 1|
75510-32| 20103006| QUILL GASKET| | 1|
75510-33| 20103002A| QUILL ARBOR| | 1|
75510-34| 16103008| DRIFT KEY| | 1|
75510-35| | THRUST BEARING| 8706| 1|
75510-36| | BEARING| 8206| 1|
75510-37| 20103001| SPINDLE| | 1|
75510-38| 20103007| ARBOR| | 1|
75510-39| 20103009| CHUCK| | 1|
75510-40| 20103009-1| CHUCK KEY| | 1|
75510-41| 20108002| CHUCK GUARD| | 1|
75510-42| 20102026A| LASER POINTER| | 2|
75510-43| | SET SCREW| M6 X 8| 2|
75510-44| 16104010| STOP PIN| | 1|
75510-45| | PIN| 8 X 25| 2|
75510-46| W20102001| HEAD STOCK| | 1|
75510-47| | PIN| 5 X 35| 2|
75510-48| | HEX HEAD BOLT| M8 X 25| 4|
75510-49| | WASHER| | 4|
75510-50| W20102007| MOTOR PLATE| | 1|
75510-51| | WASHER| | 11|
75510-52| | LOCK WASHER| | 3|
75510-53| | HEX HEAD BOLT| M8 X 16| 3|
75510-54| | NUT| M8| 4|
75510-55| YLL8024-W03| MOTOR| | 1|
75510-56| | KEY| 5 X 45| 1|
75510-57| W16205005-4| LOCK WASHER| | 1|
75510-58| W16205005-3| MOTOR PULLEY SPRING| | 1|
75510-59| W16205005-2| MOVEABLE PULLEY FLANGE| | 1|
75510-60| W16205005-1| FIXED PULLEY FLANGE| | 1|
75510-61| | SHAFT RETENTION RING| | 1|
75510-62| W20105004-5| TENSIONING PULLEY BASE| | 1|
75510-63| | PIN| 3 X 8| 1|
75510-64| W16205004-2| SLEEVE| | 1|
75510-65| | HEX HEAD BOLT| M8 X 12| 1|
| | | | |
30| | | | | | |
PARTS LIST 75-510

PART #| REFERENCE| DESCRIPTION #| SPECIFICATION| QTY
75510-66| | LOCK WASHER| | 1
75510-67| | BEARING| 61901| 1
75510-68| | RETENTION RING| | 1
75510-69| W20105007-2| TENSIONING PULLEY SHAFT| | 1
75510-70| | PIN| 5 X 32| 2
75510-71| | RETENTION RING| | 1
75510-72| | BEARING| 61905| 2
75510-73| W16205007-1| SLEEVE| | 1
75510-74| | KEY| 5 X 14| 1
75510-75| | RETENTION RING| | 1
75510-76| W16205006-2| TENSIONING PULLEY FLANGE| | 1
75510-77| W20105010| “V” BELT| 17 X 690| 1
75510-78| | RETENTION RING| | 2
75510-79| W16205006-3| TENSIONING PULLEY FLANGE| | 1
75510-80| W20105010| “V” BELT| 17 X 690| 1
75510-81| W16205006-1| UPPER TENSIONING PULLEY FLANGE| | 1
75510-82| | RETENTION RING| | 1
75510-83| W20105009-4| SPRING STOP SPACER| | 1
75510-84| W20105009-3| SPRING| | 1
75510-85| W20105009-2| UPPER PULLEY FLANGE| | 1
75510-86| W20105009-1| LOWER PULLEY FLANGE| | 1
75510-87| W16205009-5A| SPEED SENSOR TAB| | 1
75510-88| | SCREW| M4 X 6| 2
75510-89| 20102024| RETENTION RING| | 2
75510-90| | KEY| 5 X 35| 1
75510-91| W20102022| PULLEY SHAFT| | 1
75510-92| | BEARING| 6206| 2
75510-93| 20102023A| SPACER| | 1
75510-94| W20105000B| PULLEYS COVER| | 1
75510-95| 13205010| KNOB| | 1
75510-96| | SCREW| M6 X 12| 4
75510-97| | WASHER| | 4
75510-98| 16102014A| CORD CLAMP| | 1
75510-99| | SCREW| M5 X 10| 2
75510-100| 13105009| WASHER| | 4
75510-101| | NYLOCK NUT| M4| 2
75510-102| W134A05009| SENSOR PLATE| | 1
75510-103| DQ014001100-4| SENSOR| | 1
75510-104| | CAP SCREW| M2.5 X 5| 1
75510-105| | SCREW| M4 X 20| 2
75510-106| W16202027A| GEAR SHAFT| | 1
75510-107| | KEY| 3 X 8| 1
75510-108| W13202028B| FLANGE| | 1
75510-109| | SCREW| M5 X 10| 3
75510-110| W13202031| HANDLE HOLDER| | 1
75510-111| | LOCK WASHER| | 1
75510-112| | NYLOCK NUT| | 1
75510-113| C13104005| ROD| | 1
75510-114| 13204011| KNOB| | 1
75510-115| | NUT| M12| 2
75510-116| 20104008| CAP SPRING| | 1
75510-117| 20104009| SPRING| | 1
75510-118| | NUT| M10| 1
75510-119| 16102021| NYLOCK NUT| | 1
75510-120| | SCREW| ST2.9 X 6.5| 2
75510-121| DQ010003200| DIGITAL SPEED DISPLAY| | 1
75510-122| | SCREW| M5 X 6| 2
75510-123| | SPROCKET WASHER| | 2
75510-124| W20102008A| SWITCH BOX| | 1
75510-125| | SCREW| M5 X 16| 4
75510-126| KJD12| SWITCH| | 1
75510-127| | SCREW| ST4.2 X 9.5| 2
75510-128| KCD1| LAMP SWITCH| | 1
75510-129| DLCKEE3R08| POWER CORD W/PLUG| | 1
75510-130| | SCREW| M8 X 16| 2
75510-131| | ALLEN KEY| 3 MM| 1
75510-132| | ALLEN KEY| 4 MM| 1
75510-133| | ALLEN KEY| 5 MM| 1

• 8360 Champ-d’Eau, Montreal (Quebec) Canada H1P 1Y3
• Tel.: 514-326-1161
• Fax: 514-326-5565 – Parts & Service / 514-326-5555 – Order Desk
• orderdesk@general.ca
• www.general.ca

References

• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>