FIDGRA 42 Inch Retractable Ceiling Fan Instruction Manual

FIDGRA 42 Inch Retractable Ceiling Fan

Product Information

Specifications:

• Dimensions: 150mm x 60mm x 430mm
• Power Supply: 110-220V

Product Usage Instructions

General Safety Information
Before installing the fan, make sure you have all the pieces and that no pieces are lost in the foam or packaging. Remove the engine from the package to avoid damage during installation.

Maintenance
To ensure optimal performance and longevity of the fan, follow these maintenance guidelines:

• Check the bracket screws, hooks, and fan blade attachment at least twice a year to ensure they are tight.
• Clean the fan regularly using a soft cloth to avoid scratching the finish. Do not use water for cleaning as it may damage the engine, wood, or cause an electric shock.
• The engine has permanently lubricated bearings, so there is no need to lubricate the fan.

Installation
Follow these steps to install the fan:

1. Lift the fan onto the fixing support and fit the ball into the bracket.
2. Rotate the ball until its side groove lines up with the protrusion on the bracket.
3. The fan should drop slightly as it assumes the correct position, preventing the rod and fan from rotating when the unit is running.

Code Matching Method
To set up code matching for device control:

• Press the “Set Up” button or pair button within 5 seconds after powering on the device.
• If the device flashes or beeps, it means that the phone has been successfully paired with the device and can be controlled through the application.

Suspension System Installation
For suspension system installation, please refer to this video tutorial: https://youtu.be/6pK8o-mEtLY

FAQ

• Q: Do I need to lubricate the fan?
  A: No, the engine has permanently lubricated bearings, so there is no need for additional lubrication.

• Q: Can I use water to clean the fan?
  A: No, using water for cleaning may damage the engine, or wood, or cause an electric shock. Use only a soft cloth for cleaning.

• Q: How often should I check the bracket screws and fan blade attachment?
  A: It is recommended to check the bracket screws, hooks, and fan blade attachment at least twice a year to ensure they are tight.

• Q: What is the power supply requirement for the fan?
  A: The fan requires a power supply of 110-220V.

GENERAL SAFETY INFORMATION

• Before starting the fan installation, read this manual carefully and keep it for future reference.
• To reduce the risk of personal injury, attach the fan directly to the support structure of the house or building and use only the hardware provided in the package.
• Switch off the electricity before installing the fan. Make sure you have turned off all circuit breakers that power the electrical box where you are going to install the fan as well as the associated wall switch.
• All cables and connections must be made under local and national electrical rules and regulations. If you are unfamiliar with how to carry out the electrical installation, you should call in a qualified electrician.
• To reduce the risk of personal injury/injury, do not bend the blade clamping system when installing, balancing or cleaning the fan. Never insert objects between the fan blades when the fan is running.
• To reduce the risk of fire, electric shock or engine damage, do not lift or carry the fan by holding it by the electrical wires.
• This product must not be installed in contact with water.

IMPORTANT

• Before installing the fan, make sure you have all the pieces and that no pieces are lost in the foam or packaging.
• Remove the engine from the package. To avoid damage, install the engine on a smooth surface or use the foam supplied. Do not leave the fan to one side, it may damage the engine.
• Do not use a power supply that exceeds the voltage range (voltage 110V, frequency 50 Hz).
• This fan is specially designed for installation on the roof.
• Do not install the fan on high-temperature objects or damp rooms. Do not install it in greenhouses, gas pipes
• Do not connect the fan to a regulator. This can damage the engine of the device.
• On a tile with a flat and firm surface, use the screw accessory kit that comes with the bom billa.
• Do not install the fan on an unstable or inclined ceiling.

Ensure that:

1. The screws are tight
2. Connections are correct If in doubt, consult a qualified electrician.
3. The connector is well placed. In case of doubt, consult a qualified technician.

MAINTENANCE

• Due to the natural movement of the fan, some connections may come loose. Check the bracket screws, hooks, and fan blade attachment at least twice a year. Make sure they are tight.
• Clean the fan to help keep it looking new for years to come. Do not use water for cleaning as it may damage the engine, or the wood or even cause an electric shock.
• Use only a soft cloth when cleaning to avoid scratching the finish.
• No need to lubricate the fan. The engine has permanently lubricated bearings.

1. The fixing support must be screwed on to a flat, firm surface. The mounting location must be able to support ten times the static weight of the fan. The fixing support must be screwed in with the two wood screws provided. The materials provided must go into the following sequence:
   a) screw
   b) rings
   d) fixing support
   Screwthefixingsupport to the ceiling and make sure all connections are secure to prevent the fan from falling. The fixing support must be bolted abeam and not just the plasterboard. Slightly loosen the two mounting bracket screws.

2. Disassemble the stem: remove the screw from the ball and then release it. Remove the pins and U pin from the stem. If a longer stem (25 cm stem) is used, use the same ball and ground wire. Route the electrical supply cables from the top of the motor through the stem until they come out at the top. Insert the stem into the protrusion on the top of the motor housing. Gently rotate to align the holes with those in the stem. Fit the lower pinth through the boss and the stem, making sure not to pinch chor damage any cables. Secureitinplace with the U-shaped pin. Tighten all screws, preventing the stem and fan from moving relative to each other. When the above steps are all completed, insert the finial into the stem place the ball, and secure it with the top pin. Then tighten the screw securely.

3. Lift the fan onto the fixing support and fit the ball into the bracket. Rotate the ball until its side groove lines up with the protrusion on the bracket. When aligned, the fan should drop slightly as it assumes the correct position, preventing the rod and fan from rotating when the unit is running.

• Installation method: For the convenience of purchase and installation, the factory has installed the controller inside the fan, and the buyer only needs to connect the input power supply (110-220V) white line & black line

Suspension system installation : https://youtu.be/6pK80—mEtLY

Remote Control Code Matching Method
(setup) button, Pair button (segmentation) In order to ensure that the application can successfully control the device please click this button within 5 seconds after the device is powered on. If the device flashes or beeps. it means that the phone has been successfully paired with the device, and ther the device can be controlled through the application.

2.4G DC Fan Lamp Controller Specifications

Product Introduction:
This product uses 2.4G wireless digital remote control technology, remote control one—to—one control, simple and convenient operation, and strong anti—interference ability.

Technical Parameters

• Model : 2.4G AC fan light controller
• Wall switch sequence: full light/white light/yellow light
• Input voltage: ACIOOV – 130V 50/60Hz
• Output voltage : DC70 — 1 IOV
• LED output power: 25-36W
• Motor rated power: <25W
• Wind speed: 1 —6 gears
• Timing : 1 hour/ 2 hours
• Receiving method: RF2.4G
• Remote control distance: 8—20 meters
• Remote control battery: No. 7 1 .5V X2

Remote control matching code:
Turn on the power and Press and hold the light pairing key within 5 seconds of the light on, When you hear a beep or a light flashes, the code match is successful. If you need to match the code a second time, you need to wait 30 seconds before turning on the power and repeat the above operation.

CAUTION : The electronic switch is not an isolated product and needs to be operated by professional personnel during installation. The electronic switch is triggered by the remote control, and the wireless frequency of the remote control transmitter is 2.4GHz.

App operation

• Download the APP scan the QR code open the browser select the version to download
• Open the APP select a room  Click on light”* enter the equipment name (such as fan light) 0K
• Click on enter

1. Language (Chinese and English can be selected)
2. Scan (scan the other party’s QR code to share device control)
3. My QR code (you can share it with the other party)
4. Room management (room name can be added)
5. Instructions (Choose the second interface fan light, instructions for using various symbols of the device)
6. Check for updates.
7. Feedback point to enter

APP button function description

1. Code matching button (click this button within 5 seconds of turning on the light, such as the light source flashing or the buzzer “di”, it proves that the pairing code is successful;if the pairing code fails, repeat this operation).
2. After clicking, you can choose a time to turn off the device regularly.
3. After clicking, the wind blown by the fan is like the wind in nature.
4. The wind-blown by the fan after clicking is suitable for sleep.
5. After clicking, the fan will rotate in the reverse direction.
6. Click to change the direction of the wind.
7. After clicking, the fan will rotate forward.
8. After clicking, the white light and yellow light will light up at the same time, but the brightness is only 10% of the maximum brightness.
9. After clicking, the white light and yellow light will ) light up at the same time, and the brightness is the maximum brightness.
10. After clicking, only the yellow light will light up, and the brightness is the maximum brightness.
11. After clicking, only the white light will light up, and the brightness is the maximum brightness.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>