SHAPESCALE V1R0 RGB 3D Body Scanner User Manual

SHAPESCALE V1R0 RGB 3D Body Scanner

Product Information

Specifications

• Package Contents:
  • User manual
  • Shapescale Base + Arm
  • Shapescale Head
  • Carpet feet
  • Power adapter
  • Power cord
• Scanning Diameter: 5ft / 150cm
• Arm Extension: Up to 6ft / 180cm
• Minimum Clearance from Wall: 2ft / 60cm

Package Content

Product Overview

The Shapescale is a smart scale that provides body scanning capabilities. It consists of a base with an extendable arm and a detachable head. The scale is designed to be used on the floor, but can also be used with carpet feet. It features LED indicators, a speaker, and a pairing button for easy setup.

Product Setup

1. If you want to use the scale on a carpeted floor, screw in the provided carpet feet onto the base. Skip this step if you are using the scale on a hard floor.
2. Select a location with at least 2ft / 60cm of clearance from a wall. Manually rotate the arm around the base to ensure sufficient clearance.
3. Ensure that the ceiling height is higher than 6ft / 180cm and there are no objects obstructing the arm’s trajectory when it extends.
4. Avoid placing the device in overly lit or dark locations, in direct sunlight, or in front of large windows or mirrors. If scans are not successful, try moving the device to a different location.
5. Open the arm until it locks in the open position.
6. Insert the head into the top of the arm until you hear a click and the head is securely locked in place.

Wi-Fi Setup

1. Press and hold the pairing button for 5 seconds.
2. Connect the scale to power using the provided power supply.
3. The Head LED should start blinking blue, indicating that the device is in pairing mode.
4. If the LED is not blinking blue, press the pairing button for 5 seconds until it starts blinking blue.
5. Download and install the Shapescale App. Follow the onboarding process or go to your Profile – Device – Device setup to start the pairing.
6. Once you have followed the instructions in the app, the Head LEDs will turn into a rotating rainbow, indicating that the device is connected to Wi-Fi and has internet connectivity.

Your First Scan

For best results:

• Wear tight clothing or underwear.
• If you have long hair, tie it up to ensure your neck is visible.

To perform a scan:

1. Step on ShapeScale and make a fist with both hands. Stand upright with your feet separated in a wide stance. The scan will automatically start.
2. Avoid moving during the scan. Focus on an imaginary point in front of you and do not watch the product while it rotates.
3. The scan will last approximately 1 minute. Shapescale will inform you which part of your body is being scanned. The device will notify you when the scan is complete.
4. The LED will indicate the progress of the scan upload, which should take around 5 minutes at a rate of 1 MB/s (300MB). Keep the device connected to power until the scan has finished uploading.
5. Once uploaded, it will take about 5 minutes to process your scan. You will receive a notification in the app when the scan is ready. When the LED returns to rainbow, you are ready to take another scan.

Safety & Handling

For a complete list of safety and handling precautions, please review the ShapeScale User Guide at support.shapescale.com/guide.

• If the device LEDs blinking purple, please contact customer support at support.shapescale.com.
• Be careful when folding or unfolding the arm, placing your hands close to the folding mechanism could result in injury.
• The device should be kept away from children under 18 years old and pets.
• Maximum weight is 440 lbs (200 kg).
• Maximum recommended height is 6’6″ or 2m.
• The device is for indoor use only.
• The operating temperature range is 50°F to 104°F (10°C to 40°C).
• Storage temperature range is -22°F to 140°F (-30°C to +60°C).
• Avoid using the device in a humid environment. Do not submerge the device or accessories in water.
• Do not use a power supply other than the one provided, using a different power supply could result in damage or injury.
• Do not try to repair or modify this equipment yourself. No service or repairs should be performed on the ShapeScale device other than the main- tenance listed in the device’s instructions for use.
• Do not use accessories, detachable parts, or materials not described in the instructions for use. Use of parts and components other than those specified or provided by the manufacturer of this equipment could result in increased electromagnetic emissions or decreased electromagnetic immunity of this equipment and result in improved operation.
• ShapeScale should only be used on firm ground, and not on top of any other objects or platforms such as furniture.

REGULATORY INFORMATION

Not a Medical device
ShapeScale is not a medical device, it is not intended to diagnose, treat, cure, or prevent a disease or health condition. It does not have FDA or medical CE approval.

Regulatory
Regulatory certification information is available at support.shapescale.com/compliance.

FCC and ISED Canada Compliance
This device complies with part 15 of the FCC Rules and ISED Canada license- exempt RSS standards.

FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant. to part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy.
If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. Verification of harmful interference by this equipment to radio or television reception can be determined by turning it off and then on. The user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a different circuit to that of the receiver’s outlet.
• Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
The emissions are maintained within the band of operation under all conditions of normal operation.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an controlled environment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.

ISEDC Statement

This device complies with the Innovation, Science and Economic Development Canada license-exempt RSS standard (s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

ISEDC Radiation Exposure Statement

This equipment complies with ISEDC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20cm between the radiator &your body.
Shape Labs Inc. hereby declares that this wireless device is in compliance with Directive 2014/53/EU. A copy of the declaration of conformity is available at suppo .shapescale.com/compliance.

Disposal and Recycling information

The symbol above means that according to local laws and regulations your product shall be disposed of separately from household waste.
When this product reaches its end of life, take it to a collection point designated by local authorities.

Class 1 Laser information

This device is classified as a Class 1 Laser Product under the EN/IEC 60825-1, Edition 3 (2014) internationally. This product complies with FDA performance standards for laser products except for conformance with IEC 60825-1 Ed. 3 as described in Laser Notice No. 56, dated May 8, 2019. This device contains one or more lasers. Use other than described in the user guide, repair, or disassembly may cause damage, which could result in hazardous exposure to infrared emissions that are not visible.

ShapeScale one-year limited warranty

Shape warrants the device and accessories against defects in materials and workmanship for one year from the date of original purchase. Shape does not warrant against normal wear and tear, nor damage caused by accident or abuse.

SCAN QR CODE TO GET STARTED OR VISIT SUPPORT.SHAPESCALE.COM/GUIDE

FAQ

Q: Can I use the Shapescale on a carpeted floor?

A: Yes, you can use the Shapescale on a carpeted floor by attaching the provided carpet feet to the base.

Q: What should I do if the Head LED ring is red?

A: If the Head LED ring is red, it means that the device cannot connect to Wi- Fi. Please check your Wi-Fi settings and ensure that your internet connection is working properly.

Q: How long does it take to process a scan?

A: It takes approximately 5 minutes to process a scan once it has been uploaded.

References

• ShapeScale ® — 3D Body Scanner · Scale · Fitness Tracker
• ShapeScale Help Center
• ShapeScale Help Center

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>