LG 48CXAUB LED TV Smart Owner’s Manual
- June 16, 2024
- LG
Table of Contents
- LG 48CXAUB LED TV Smart
- Product Specifications
- Important Safety Instructions
- Warning! Safety Instructions
- Preparing
- Product Usage Instructions
- Frequently Asked Questions (FAQ)
- Lifting and moving the TV
- External Devices
- How to register the Magic Remote Control
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
LG 48CXAUB LED TV Smart
Product Specifications
- Model Numbers: OLED48CXAUB, OLED48CXPUB, OLED55BXPUA,
- OLED55BXAUA, OLED55CXPUA, OLED55CXAUA, OLED65BXPUA, OLED65BXAUA,
- OLED65CXPUA, OLED65CXAUA, OLED77BXPUA, OLED77BXAUA, OLED77CXPUA,
- OLED77CXAUA
- Manufacturer: LG
- Website: www.lg.com
Important Safety Instructions
Before operating the set, please read the following safety instructions:
- If the power cord or plug is damaged, liquid has been spilled into the apparatus, or objects have fallen into the apparatus, do not operate the set and contact qualified service personnel.
- If the set does not operate normally or has been dropped, do not attempt to repair it yourself. Contact qualified service personnel.
- By using this product, you agree that all disputes between you and LG shall be resolved through binding arbitration on an individual basis.
- More information on the arbitration agreement can be found at www.lg.com/us/arbitration (USA) or www.lg.com/ca_en/arbitration (Canada).
Warning! Safety Instructions
To reduce the risk of electric shock and fire:
- Do not open the cover or back of the set. There are no user serviceable parts inside. Refer to qualified service personnel for any repairs.
- Do not expose the product to rain or moisture.
- The power plug is the disconnecting device. In case of an emergency, the power plug must remain readily accessible.
Preparing
Before using the TV, follow these steps:
- Optional Extras: Some devices or features mentioned in the manual may require additional accessories that are not included with the TV.
- Initialization: When you first turn on the TV, it may take approximately one minute to initialize.
- Refer to Manual: Make sure to refer to the manual specific to your TV model for accurate instructions and information.
- Power On/Off: Some devices are not turned on or off by pressing the power button. Make sure to check the specific instructions for the device you are using.
- Product Upgrades: The TV’s functions may be upgraded without prior notice, resulting in changes to the user interface or features.
- USB Port Compatibility: If the USB cable or USB flash drive does not fit into your TV’s USB port, check the compatibility and ensure proper insertion.
Product Usage Instructions
To operate your TV, use the following remote control buttons:
B | A | (Arrow Key / Right Key) |
---|---|---|
07 | (Arrow Key / Left Key) | |
08 | Power | |
09 | Mute | |
0B | Input | |
0E | SLEEP | |
0F | TV, TV/RAD | |
10 – 19 | Number Key 0 – 9 | |
1A | Q.View / Flashback | |
1E | FAV (Favorite Channel) | |
20 | Text (Teletext) | |
21 | T. Opt (Teletext Option) | |
28 | Return (BACK) | |
30 | AV (Audio / Video) Mode | |
39 | Caption/Subtitle | |
40 | (Arrow Key / Cursor Up) | |
41 | V (Arrow Key / Cursor Down) | |
42 | My Apps | |
43 | Menu / Settings | |
44 | OK / Enter | |
45 | Q.Menu | |
4C | List, – | |
4D | PICTURE | |
52 | SOUND |
Frequently Asked Questions (FAQ)
Q: What should I do if the power cord or plug is damaged?
A: If the power cord or plug is damaged, do not operate the set and contact
qualified service personnel.
Q: How can I access the arbitration agreement?
A: The arbitration agreement can be accessed at
www.lg.com/us/arbitration (USA) or
www.lg.com/ca_en/arbitration (Canada).
Q: Can I open the cover or back of the set?
A: No, do not open the cover or back of the set. There are no user serviceable
parts inside. Refer to qualified service personnel for any repairs.
Q: Can I expose the product to rain or moisture?
A: No, do not expose the product to rain or moisture.
Important Safety Instruction
· Read these instructions. · Keep these instructions. · Heed all warnings. ·
Follow all instructions. · Do not use this apparatus near water. · Clean only
with dry cloth. · Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions. · Do not install near any heat sources
such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat. · Do not defeat the safety purpose of the
polarized or grounding-type plug. A polarized plug has two blades with one
wider than the other. A
grounding type plug has two blades and a third grounding prong. The wide blade
or the third prong are provided for your safety. If the provided plug does not
fit into your outlet, consult an electrician for replacement of the obsolete
outlet. · Protect the power cord from being walked on or pinched particularly
at plugs, convenience receptacles, and the point where they exit from the
apparatus. · Only use attachments/accessories specified by the manufacturer. ·
Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tip-over.
· Unplug this apparatus during lightning storms or when unused for long
periods of time. · Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been damaged in any way, such as
power-supply
cord or plug is damaged, liquid has been spilled or objects have fallen into
the apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
By using this product, you agree that all disputes between you and LG arising
out of or relating in any way to this product (including but not limited to
warranty disputes) shall be resolved exclusively through binding arbitration
on an individual basis. The terms of the arbitration agreement (including
details on the procedure for resolving disputes) is available at
www.lg.com/us/arbitration (USA) or www.lg.com/ca_en/arbitration (Canada). 2
ENGLISH _index
Warning! Safety instructions
CAUTION RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.
The symbol is intended to alert the user to the presence of uninsulated
dangerous voltage within the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons. The symbol is
intended to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying the
device. WARNING: TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE
THIS PRODUCT TO RAIN OR MOISTURE.
· TO PREVENT THE SPREAD OF FIRE, KEEP CANDLES OR OTHER ITEMS WITH OPEN FLAMES
AWAY FROM THIS PRODUCT AT ALL TIMES.
· Do not place the TV and/or remote control in the following environments: –
Keep the product away from direct sunlight. – An area with high humidity such
as a bathroom – Near any heat source such as stoves and other devices that
produce heat. – Near kitchen counters or humidifiers where they can easily be
exposed to steam or oil. – An area exposed to rain or wind. – Do not expose to
dripping or splashing and do not place objects filled with liquids, such as
vases, cups, etc. on or over the apparatus (e.g., on shelves above the unit).
– Near flammable objects such as gasoline or candles, or expose the TV to
direct air conditioning. – Do not install in excessively dusty places.
Otherwise, this may result in fire, electric shock, combustion/ explosion,
malfunction or product deformation.
· Ventilation – Install your TV where there is proper ventilation. Do not
install in a confined space such as a bookcase. – Do not install the product
on a carpet or cushion. – Do not block or cover the product with cloth or
other materials while unit is plugged in.
· Take care not to touch the ventilation openings. When watching the TV for a
long period, the ventilation openings may become hot.
· Protect the power cord from physical or mechanical abuse, such as being
twisted, kinked, pinched, closed in a door, or walked upon. Pay particular
attention to plugs, wall outlets, and the point where the cord exits the
device.
· Do not move the TV whilst the Power cord is plugged in. · Do not use a
damaged or loosely fitting power cord. · Be sure do grasp the plug when
unplugging the power cord. Do
not pull on the power cord to unplug the TV. · Do not connect too many devices
to the same AC power outlet as
this could result in fire or electric shock. · Disconnecting the Device from
the Main Power
– The power plug is the disconnecting device. In case of an emergency, the
power plug must remain readily accessible.
· Do not let your children climb or cling onto the TV. Otherwise, the TV may
fall over, which may cause serious injury.
· Outdoor Antenna Grounding (Can differ by country): – If an outdoor antenna
is installed, follow the precautions below. An outdoor antenna system should
not be located in the vicinity of overhead power lines or other electric light
or power circuits, or where it can come in contact with such power lines or
circuits as death or serious injury can occur. Be sure the antenna system is
grounded to provide some protection against voltage surges and built-up static
charges. Section 810 of the National Electrical Code (NEC) in the U.S.A.
provides information with respect to proper grounding of the mast and
supporting structure, grounding of the lead-in wire to an antenna discharge
unit, size of grounding conductors, location of antenna discharge unit,
connection to grounding electrodes and requirements for the grounding
electrode. Antenna grounding according to the National Electrical Code,
ANSI/NFPA 70
3
ENGLISH _index
· Grounding (Except for devices which are not grounded.) – TV with a three-
prong grounded AC plug must be connected to a three-prong grounded AC outlet.
Ensure that you connect the earth ground wire to prevent possible electric
shock.
· Never touch this apparatus or antenna during a lightning storm. You may be
electrocuted.
· Make sure the power cord is connected securely to the TV and wall socket if
not secured damage to the Plug and socket may occur and in extreme cases a
fire may break out.
· Do not insert metallic or inflammable objects into the product. If a foreign
object is dropped into the product, unplug the power cord and contact the
customer service.
· Do not touch the end of the power cord while it is plugged in. You may be
electrocuted.
· If any of the following occur, unplug the product immediately and contact
your local customer service. – The product has been damaged. – If water or
another substance enters the product (like an AC adapter, power cord, or TV).
– If you smell smoke or other odors coming from the TV – When lightning storms
or when unused for long periods of time.
Even the TV is turned off by remote control or button, AC power source is
connected to the unit if not unplugged in. · Do not use high voltage
electrical equipment near the TV (e.g., a bug zapper). This may result in
product malfunction. · Do not attempt to modify this product in any way
without written authorization from LG Electronics. Accidental fire or electric
shock can occur. Contact your local customer service for service or repair.
Unauthorized modification could void the user’s authority to operate this
product. · Use only an authorized attachments / accessories approved by LG
Electronics. Otherwise, this may result in fire, electric shock, malfunction,
or product damage. · Never disassemble the AC adapter or power cord. This may
result in fire or electric shock. · Handle the adapter carefully to avoid
dropping or striking it. An impact could damage the adapter. · To reduce the
risk of fire or electrical shock, do not touch the TV with wet hands. If the
power cord prongs are wet or covered with dust, dry the power plug completely
or wipe dust off.
· Batteries – Store the accessories (battery, etc.) in a safe location out of
the reach of children. – Do not short circuit, disassemble, or allow the
batteries to overheat. Do not dispose of batteries in a fire. Batteries should
not be exposed to excessive heat. – Caution: Risk of fire or explosion if the
battery is replaced by an incorrect type.
· Moving – When moving, make sure the product is turned off, unplugged, and
all cables have been removed. It may take 2 or more people to carry larger
TVs. Do not press or put stress on the front panel of the TV. Otherwise, this
may result in product damage, fire hazard or injury.
· Keep the packing anti-moisture material or vinyl packing out of the reach of
children.
· Do not allow an impact shock, any objects to fall into the product, and do
not drop anything onto the screen.
· Do not press strongly upon the panel with a hand or a sharp object such as a
nail, pencil, or pen, or make a scratch on it. It may cause damage to screen.
· Cleaning – When cleaning, unplug the power cord and wipe gently with a
soft/dry cloth. Do not spray water or other liquids directly on the TV. Do not
clean your TV with chemicals including glass cleaner, any type of air
freshener, insecticide, lubricants, wax (car, industrial), abrasive, thinner,
benzene, alcohol etc., which can damage the product and/or its panel.
Otherwise, this may result in electric shock or product damage.
4
ENGLISH _index
Preparing
Optional Extras
· When the TV is turned on for the first time after being shipped
from the factory, initialization of the TV may take approximately
one minute.
· Image shown may differ from your TV.
· Your TV’s OSD (On Screen Display) may differ slightly from that
shown in this manual.
· The available menus and options may differ from the input source
or product model that you are using.
· New features may be added to this TV in the future.
· The device must be easily accessed to a location outlet near the
access. Some devices are not made by turning on / off button,
turning off the device and unplugging the power cord.
· The items supplied with your product may vary depending upon
the model.
· Product specifications or contents of this manual may be changed
without prior notice due to upgrade of product functions.
· For an optimal connection, HDMI cables and USB devices should
have bezels less than 10 mm (0.39 inches) thick and 18 mm (0.7
inches) width. · Use an extension cable that supports
if the USB cable or
USB flash drive does not fit into your TV’s USB port.
B
B * A <= 10 mm (0.39 inches)
A
A
- B <= 18 mm (0.7 inches)
· Use a certified cable with the HDMI logo attached. If you do not use a
certified HDMI cable, the screen may not display or a connection
error may occur. · Recommended HDMI cable types (3 m (9.84 ft) or less)
– Ultra High Speed HDMI®/TM cable · When attaching the stand to the TV set,
place the screen facing
down on a cushioned table or flat surface to protect the screen
from scratches. · Make sure to wring any excess water or cleaner from the
cloth. · Do not spray water or cleaner directly onto the TV screen. · Make
sure to spray just enough of water or cleaner onto a dry cloth
to wipe the screen.
Optional extras can be changed or modified for quality improvement without any
notification. Contact your dealer for buying these items. These devices work
only with certain models. The model name or design may be changed due to the
manufacturer’s circumstances or policies.
Magic Remote Control
MR20GA
Check whether your TV model supports Bluetooth in the Wireless Module
Specification to verify whether it can be used with the Magic Remote.
Wall Mounting Bracket
(Depending upon model) Make sure to use screws and wall mount bracket that
meet the VESA standard. Standard dimensions for the wall mount kits are
described in the following table.
A B
Model
OLED55/65BX OLED48/55/65CX
VESA (A x B) (mm) 300 x 200
Standard screw M6
Number of screws 4
Wall mount bracket OLW480B
OLED77BX OLED77CX 400 x 200 M6 4 OLW480B
5
ENGLISH _index
Lifting and moving the TV
When moving or lifting the TV, read the following to prevent the TV from being
scratched or damaged and for safe transportation regardless of its type and
size.
· It is recommended to move the TV in the box or packing material that the TV
originally came in.
· Before moving or lifting the TV, disconnect the power cord and all cables.
· When holding the TV, the screen should face away from you to avoid damage.
· Avoid touching the screen at all times, as this may result in damage to the
screen.
· Do not place the product on the floor with its front facing down without
padding. Failure to do so may result in damage to the screen.
· When attaching the stand to the TV set, place the screen facing down on a
cushioned table or flat surface to protect the screen from scratches.
Mounting on the Table
1 Lift and tilt the TV into its upright position on a table. · Leave a minimum
of 10 cm (4 inches) space from the wall for proper ventilation.
· Hold the side and bottom of the TV frame firmly. Make sure not to hold the transparent part, speaker, or speaker grill area.
10 cm
(4 inches)
10 cm
10 cm
10 cm 10 cm
· Use at least two people to move a large TV. · When transporting the TV by
hand, hold the TV as shown in the
following illustration.
· When transporting the TV, do not expose the TV to jolts or excessive
vibration.
· When transporting the TV, keep the TV upright; never turn the TV on its side
or tilt towards the left or right.
· When handling the TV, be careful not to damage the protruding buttons.
(Depending upon model)
2 Connect the power cord to a wall outlet. · Do not apply foreign substances
(oils, lubricants, etc.) to the screw parts when assembling the product.
(Doing so
may damage the product.) · If you install the TV on a stand, you need to take
actions
to prevent the product from overturning. Otherwise, the
product may fall over, which may cause injury. · Do not use any unapproved
items to ensure the safety
and lifespan of the product. · Any damages or injuries by using unapproved
items are
not covered by the warranty. · Make sure that the screws are fastened tightly.
(If they
are not fastened securely enough, the TV may tilt forward
after being installed.) · Do not fasten the screws with excessive force
otherwise
they may strip and become loose.
(Depending upon model)
1 Insert and tighten the eye-bolts, or TV brackets and bolts on the back of
the TV. · If there are bolts inserted at the eye-bolts position, remove the
bolts first.
2 Mount the wall brackets with the bolts to the wall. Match the location of
the wall bracket and the eye-bolts on the rear of the TV.
3 Connect the eye-bolts and wall brackets tightly with a sturdy rope or cable.
Make sure to keep the rope parallel to the flat surface.
· Use a platform or cabinet that is strong and large enough to support the TV
securely.
· Brackets, bolts and ropes are optional. You can obtain additional
accessories from your local dealer.
An optional wall mount can be used with your LG Television. Consult with your local dealer for a wall mount that supports the VESA standard used by your TV model. Carefully attach the wall mount bracket at the rear of the TV. Install the wall mount bracket on a solid wall perpendicular to the floor. If you are attaching the TV to other building materials, please contact qualified personnel to install the wall mount. Detailed instructions will be included with the wall mount. We recommend that you use an LG brand wall mount. The LG wall mount is easy to adjust or to connect the cables. When you do not use LG’s wall mount bracket, use a wall mount bracket where the device is adequately secured to the wall with enough space to allow connectivity to external devices. If you are using a non-adjustable mount, attach the mount to the wall. Attach the cables to the TV first, then attach the TV to the mount.
10 cm
(4 inches)
10 cm
10 cm
10 cm 10 cm
(Depending upon model) · Remove the stand before installing the TV on a wall
mount by performing the stand attachment in reverse. · For more information of
screws and wall mount bracket,
refer to the Separate purchase. · If you intend to mount the product to a
wall, attach VESA
standard mounting interface (optional parts) to the back
of the product. When you install the set to use the wall
mounting bracket (optional parts), fix it carefully so as
not to drop. · When mounting a TV on the wall, make sure not to install
the TV by hanging the power and signal cables on the
back of the TV. · Do not install this product on a wall if it could be exposed
to oil or oil mist. This may damage the product and cause
it to fall.
7
ENGLISH _index
· Please use the accessory cable holder when hanging on the wall. (Only
OLED48/55/65/77CX*)
Connections
You can connect various external devices to the TV. For more information on
external device’s connection, refer to the manual provided with each device.
Antenna/Cable
Connect an antenna, cable, or cable box to watch TV while referring to the
following. The illustrations may differ from the actual items and an RF cable
is optional.
· Make sure not to bend the copper wire of the RF cable.
Other connections
Connect your TV to external devices. For the best picture and audio quality,
connect the external device and the TV with the HDMI cable.
HDMI
· When connecting the HDMI cable, the product and external devices should be
turned off and unplugged.
· Supported HDMI Audio format (Depending upon model): True HD (48 kHz), Dolby
Digital / Dolby Digital Plus (32 kHz, 44.1 kHz, 48 kHz), PCM (32 kHz, 44.1
kHz, 48 kHz, 96 kHz, 192 kHz)
· [Picture] [Additional Settings] [HDMI Ultra HD Deep Color] (OLED55/65/77BX)
– On: Support 4K @ 50/60 Hz (4:4:4, 4:2:2, 4:2:0), <3,4 port only> 4K @
100/120 Hz (4:4:4, 4:2:2, 4:2:0) – Off: Support 4K @ 50/60 Hz (4:2:0)
(OLED48/55/65/77CX) – On: Support 4K @ 50/60 Hz (4:4:4, 4:2:2, 4:2:0), 4K @
100/120 Hz (4:4:4, 4:2:2, 4:2:0) – Off: Support 4K @ 50/60 Hz (4:2:0) If the
device connected to Input Port also supports Ultra HD Deep Color, your picture
may be clearer. However, if the device doesn’t support it, it may not work
properly. In that case, change the TV’s [HDMI Ultra HD Deep Color] setting to
off.
Copper wire
· Complete all connections between devices, and then connect the power cord to
the power outlet to prevent damage to your TV.
· Use a signal splitter to use 2 TVs or more. · DTV Audio Supported Codec:
MPEG, Dolby Digital · This TV cannot receive Ultra HD (3840 x 2160 pixels)
broadcasts
directly because the related standards have not been confirmed.
8
ENGLISH _index
External Devices
Supported external devices are: Blu-ray player, HD receivers, DVD players,
VCRs, audio systems, USB storage devices, PC, gaming devices, and other
external devices.
· If you record a TV program on a Blu-ray/DVD recorder or VCR, make sure to
connect the TV signal input cable to the TV through a DVD recorder or VCR. For
more information about recording, refer to the manual provided with the
connected device.
· The external device connections shown may differ slightly from illustrations
in a manual.
· Connect external devices to the TV regardless about the order of the TV
port.
· If you connect a gaming device to the TV, use the cable supplied with the
gaming device.
· Refer to the external equipment’s manual for operating instructions.
· In PC mode, there may be noise associated with the resolution, vertical
pattern, contrast or brightness. If noise is present, change the PC output to
another resolution, change the refresh rate to another rate or adjust the
brightness and contrast on the [Picture] menu until the picture is clear.
Depending upon the graphics card, some resolution settings may not allow the
image to be positioned on the screen properly.
· Some USB Hubs may not work. If a USB device connected through a USB Hub is
not detected, connect it directly to the USB port on the TV.
· When connecting via a wired LAN, it is recommended to use a CAT 7 cable.
· The TV may be capable of operating without a set-top-box from a multichannel
video programming distributor (MVPD).
Remote RS-232C setup
To obtain the RS-232C external control setup information, please visit
www.lg.com. Download and read the manual, (Depending upon model).
· Do not drop the product or let it fall over when connecting external
devices. Otherwise, this may result in injury or damage to the product.
· When connecting external devices such as video game consoles, make sure the
connecting cables are long enough. Otherwise, the product may fall over, which
may cause injury or damage the product.
9
ENGLISH _index
Using Button
You can simply operate the TV functions, using the button.
Basic functions
Power On (Press) Power Off1 (Press and Hold) Menu Control (Press2) Menu
Selection (Press and Hold3) 1 All running apps will close. 2 You can access
and adjust the menu by pressing the button when TV is on. 3 You can use the
function when you access menu control.
Power On (Press) Power Off 1 (Press and hold)
Volume Control
Channels Control
1 All running apps will close. Adjusting the menu When the TV is turned on,
press the button one time. You can adjust the Menu items using the button. <A
type>
Turns the power off. Changes the input source.
Adjusts the volume level.
Scrolls through the saved channels.
Turns the power off. Accesses the settings menu. Clears on-screen
displays and returns to TV viewing. Changes the input source.
10
ENGLISH _index
Using Magic Remote Control
The descriptions in this manual are based on the buttons on the remote
control. Please read this manual carefully and use the TV correctly. When the
message [Magic Remote battery is low. Please change the battery.] is
displayed, replace the batteries. To install batteries, open the battery
cover, replace batteries (1.5 V AA) matching the and ends to the label inside
the compartment, and close the battery cover. Be sure to point the magic
remote toward the remote control sensor on the TV. To remove the batteries,
perform the installation actions in reverse. This remote uses infrared light.
When in use, it should be pointed in the direction of the TV’s remote sensor.
1
1
1
(Some buttons and services may not be provided depending upon models or regions.)
To use the button, press and hold for more than 1 second.
(POWER) Turns the TV on or off.
(STB POWER) You can turn your set-top box on or off by adding
the settop box to the universal remote control for your TV.
Number buttons Enters numbers.
** Accesses the [Quick Help].
(DASH) Inserts a between numbers such as 2-1 and 2-2.
Accesses the saved channel list.
(MORE ACTIONS) Displays more remote control functions.
** Edits QUICK ACCESS
– QUICK ACCESS is a feature that allows you to enter a specified app
or Live TV directly by pressing and holding the number buttons.
** SAP (Secondary Audio Program) feature can also be
enabled by pressing the button.
Adjusts the volume level.
(MUTE) Mutes all sounds.
** (MUTE) Accesses the [Accessibility] menu.
Scrolls through the saved channels.
(Voice recognition) Network connection is required to use the
voice recognition function.
Check for recommended content. (Some recommended services may
not be available in some countries.)
(Voice recognition) Speak while pressing and holding the
button to use the voice recognition feature.
(HOME) Accesses the Home menu.
** (HOME) Shows the previous history.
(Q. Settings) Accesses the Quick Settings.
** (Q. Settings) Displays the [All Settings] menu.
Wheel (OK) Press the center of button to select a menu. You
can change channels by using button.
(up/down/left/right) Press the up, down, left or right
button to scroll the menu. If you press
buttons while
the pointer is in use, the pointer will disappear from the screen and
Magic Remote will operate like a general remote control. To display
the pointer on the screen again, shake Magic Remote to the left and
right.
(BACK) Returns to the previous level.
** (BACK) Clears on-screen displays and returns to last input
viewing.
Displays the program event according to time scheduler.
1 Streaming Service buttons Connects to the Video Streaming
Service.
(INPUT) Changes the input source.
** (INPUT) Accesses the [Home Dashboard].
, , , These access special functions in some
menus.
, (Control buttons) Controls media contents.
11
ENGLISH _index
Registering Magic Remote Control User Guide
How to register the Magic Remote Control
To use the Magic Remote, first pair it with your TV. 1 Put batteries into the
Magic Remote and turn the TV on. 2 Point the Magic Remote at your TV and press
the Wheel (OK) on
the remote control. If the TV fails to register the Magic Remote, try again
after turning
the TV off and back on.
How to deregister the Magic Remote Control
Press the (BACK) and (HOME) buttons at the same time, for five seconds, to
unpair the Magic Remote with your TV. Press and hold the button for more
than 5 seconds to disconnect
and re-register the Magic Remote at the same time.
· It is recommended that an Access Point (AP) be located more than 0.2 m (0.65
ft) away from the TV. If the AP is installed closer than 0.2 m (0.65 ft), the
Magic remote control may not perform as expected due to frequency
interference.
· Do not mix new batteries with old batteries. This may cause the batteries to
overheat and leak.
· Failure to match the correct polarities of the battery may cause the battery
to burst or leak, resulting in fire, personal injury, or ambient pollution.
· This apparatus uses batteries. In your community there might be regulations
that require you to dispose of these batteries properly due to environmental
considerations. Please contact your local authorities for disposal or
recycling information.
· Batteries inside or inside the product shall not be exposed to excessive
heat such as sunshine, fire or the like.
For more information about this TV, read the USER GUIDE embedded in the
product.
· To open the USER GUIDE [Support] [User Guide] Troubleshooting
Cannot control the TV with the remote control. · Check if anything such as
tape has been placed over the receiver. · Check if there is any obstacle
between the product and the remote control. · Replace the batteries with new
fresh ones.
No image display and no sound is produced. · Check if the product is turned
on. · Check if the power cord is connected to a wall outlet. · Check if there
is a problem in the wall outlet by connecting other products.
The TV turns off suddenly. · Check the power control settings. The power
supply may be interrupted. · Check if the auto-off function is activated in
the settings menu. · If there is no signal while the TV is on, the TV will
turn off automatically after 15 minutes of inactivity.
12
ENGLISH _index
Abnormal Display · If the TV feels cold to the touch, there may be a small
flicker when it is turned on. This is normal; there is nothing wrong with TV.
Some minute dot defects may be visible on the screen, appearing as tiny red,
green, or blue spots. However, they have no adverse effect on the TV’s
performance. Avoid touching the screen or holding your finger(s) against it
for long periods of time. Doing so may produce some temporary distortion
effects on the screen. · This panel is an advanced product that contains
millions of pixels. In a very few cases, you could see fine dots on the screen
while you’re viewing the TV. Those dots are deactivated pixels and do not
affect the performance and reliability of the TV.
Generated Sound · Cracking noise A cracking noise that occurs when watching or
turning off the TV is generated by plastic thermal contraction due to
temperature and humidity. This noise is common for products where thermal
deformation is required. · Electrical circuit humming/panel buzzing A low
level noise is generated from a high-speed switching circuit, which supplies a
large amount of current to operate a product. It varies depending upon the
product. This generated sound does not affect the performance and reliability
of the product.
· Make sure to wring any excess water or cleaner from the cloth.
· Do not spray water or cleaner directly onto the TV screen. · Make sure to
spray just enough of water or cleaner onto a
dry cloth to wipe the screen.
13
ENGLISH _index
Specifications
Product specifications may be changed without prior notice due to upgrade of
product functions. Estimated yearly energy consumption indicated on the FTC
label is measured in accordance with the Test Procedures for Television Sets
(USA only). The actual energy consumption depends on the usage environment
(The content watched, TV settings, etc.).
· For information of the power supply and power consumption, refer to the
label attached to the product. – The typical power consumption is measured in
accordance with IEC 62087 or each country’s energy regulations. On some
models, the label is inside the external device connection terminal cover.
Depending upon the model or country, the typical power consumption may not be
on label.
Broadcasting Specifications
Television system
ATSC / NTSC-M, 64 & 256 QAM
Program coverage
VHF 2-13, UHF 14-69, DTV 2-69, CATV 1-135, CADTV 1-135
External antenna impedance
75
Wireless module (LGSBWAC92) Specifications
Wireless LAN (IEEE 802.11a/b/g/n/ac)
Frequency Range
Output Power (Max.)
2,400 to 2,483.5 MHz 5,150 to 5,725 MHz 5,725 to 5,850 MHz
18 dBm 18 dBm 18 dBm
Bluetooth
Frequency Range
Output Power (Max.)
2,400 to 2,483.5 MHz
8 dBm
As band channels can vary per country, the user cannot change or adjust the operating frequency. This product is configured for the regional frequency table. For consideration of the user, this device should be installed and operated with a minimum distance of 20 cm (7.8 inches) between the device and the body. FCC ID: BEJLGSBWAC92 / IC: 2703H-LGSBWAC92
Operating Temperature Operating Humidity Storage Temperature Storage Humidity
Environment condition
0 °C to 40 °C (32 °F to 104 °F) Less than 80 %
-20 °C to 60 °C (-4 °F to 140 °F) Less than 85 %
14
ENGLISH _index
Open Source Software Notice Information
To obtain the source code under GPL, LGPL, MPL, and other open source
licenses, that is contained in this product, please visit http://opensource.
lge.com. In addition to the source code, all referred license terms, warranty
disclaimers and copyright notices are available for download. LG Electronics
will also provide open source code to you on CD-ROM for a charge covering the
cost of performing such distribution (such as the cost of media, shipping, and
handling) upon email request to opensource@lge.com. This offer is valid for a
period of three years after our last shipment of this product. This offer is
valid to anyone in receipt of this information.
Licenses
(Magic Remote supported models only)
15
ENGLISH _index
Important Information for Preventing Image Retention
OLED is a self-emissive technology, which brings many significant benefits to
image quality and performance. As with any self-emitting display, it is
possible for users of OLED TVs to experience temporary image retention under
certain conditions, such as when displaying a static image on the screen for a
long time. LG OLED TVs incorporate dedicated functions that protect the screen
from possible image retention. If a static image persists on screen, screen
brightness is automatically reduced in specific areas of, or across the entire
screen. Once the static image disappears, screen brightness will automatically
return to its prior setting. This is not a product malfunction.
Examples of Images that may Cause Image Retention
· Still images or fixed images containing certain information that are
displayed uninterrupted on the screen, such as channel numbers, station logos,
program titles, news or movie subtitles, and headlines.
· Fixed menu or icons for video game consoles or broadcasting set-top boxes.
· Black bars shown on the left, right, top, or bottom of the screen, such as
in images with a 4:3 or 21:9 ratio.
Recommended Measures for Preventing Image Retention
· Avoid watching a video displaying an image as listed above for extended
periods of time.
· Adjust your TV settings as below when turning on a video exhibiting an image
as listed above for extended periods of time. – [Picture] [Picture Mode
Settings] [Picture Mode] [APS] – [Picture] [Picture Mode Settings] [OLED
LIGHT] Adjust to lower value – [Picture] [OLED Screen Saver] [Logo Luminance
Adjustment] [High] · Turn off the menu bar of an external device, such as a
set-top box, to prevent long-term display of the menu bar of such device.
(Please refer to the manual of the applicable external device for
instructions.)
· Adjust the settings as below when watching a video constantly showing black
bars on the left, right, top or bottom, in order to remove the black bars. –
[Picture] [Aspect Ratio Settings] [Aspect Ratio] [Vertical Zoom] or [4-Way
Zoom] Information on Functions Supporting Image Quality in Relation to
Temporary Image Retention
· LG OLED TVs provide a feature called Pixel Refresher, which helps to prevent
temporary image retention.
· When the accumulated television viewing time reaches 2,000 hours or more
(this is equivalent to watching TV for five hours a day over the course of a
year), Pixel Refresher will be automatically activated once your TV is turned
off. When turning off your TV, a notice will appear on the screen informing
the activation of Pixel Refresher. This feature will run for an hour while
your TV is turned off. A horizontal line may appear at the top or bottom of
the screen when the process is almost finished.
· You may also manually activate Pixel Refresher via the TV menu: [Picture]
[OLED Screen Saver] [Pixel
Refresher]. · Whenever you watch your TV for more than four cumulative hours,
Pixel Refresher will be automatically activated for a few minutes once your TV
is turned off. (Note: Pixel Refresher will not be activated if the power cord
of your TV is not plugged in or the main power is off.)
16
ENGLISH _index
Regulatory
–
17
ENGLISH _index
WARNING!
Never place a television set in an unstable location. A television set may
fall, causing serious personal injury or death. Many injuries, particularly
(1)
to children, can be avoided by taking simple precautions such as:
· Using cabinets or stands recommended by the manufacturer of the
television set.
(2)
· Only using furniture that can safely support the television set.
· Ensuring the television set is not overhanging the edge of the
supporting furniture.
· Not placing the television set on tall furniture (for example,
(3)
cupboards or bookcases) without anchoring both the furniture and
the television set to a suitable support.
· Not placing the television set on cloth or other materials that may
be located between the television set and supporting furniture.
(4)
· Educating children about the dangers of climbing on furniture to
reach the television set or its controls.
If your existing television set is being retained and relocated, the same
considerations as above should be applied.
Symbols
NOTE TO CABLE/TV INSTALLER
(For USA and Canada) This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the National Electric Code
(U.S.A.). The code provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be connected to the
grounding system of the building, as close to the point of the cable entry as
practical.
Refers to alternating current (AC). Refers to direct current (DC). Refers to class II equipment. Refers to stand-by. Refers to “ON” (power). Refers to dangerous voltage.
18
ENGLISH _index
CHILD SAFETY:
PROPER TELEVISION PLACEMENT MATTERS
THE CONSUMER TECHNOLOGY INDUSTRY CARES
Manufacturers, retailers and the rest of the consumer technology industry are
committed to making products safe and enjoyable. As you enjoy your television,
please note that all televisions new and old- must be supported on proper
stands or installed according to the manufacturer’s recommendations.
Televisions that are inappropriately situated on dressers, bookcases, shelves,
desks, speakers, chests, carts, etc., may fall over, resulting in injury.
TUNE IN TO SAFETY
· NEVER allow children to climb on or play on the television or the furniture
on which the television is placed. · NEVER place the television on furniture
that can easily be used as steps, such as a chest of drawers. · ALWAYS follow
the manufacturer’s recommendations for the safe installation of your
television. · ALWAYS read and follow all instructions for proper use of your
television. · ALWAYS install the television where it cannot be pushed, pulled
over or knocked down. · ALWAYS route cords and cables connected to the
television so that they cannot be tripped over, pulled or grabbed.
WALL OR CEILING MOUNT YOUR TELEVISION
· ALWAYS contact your retailer about professional installation if you have any
doubts about your ability to safely mount your television. · ALWAYS use a
mount that has been recommended by the television manufacturer and has a
safety certification by a Nationally Recognized Testing Laboratory (NRTL). ·
ALWAYS follow all instructions supplied by the television and mount
manufacturers. · ALWAYS make sure that the wall or ceiling where you are
mounting the television is appropriate. Use proper anchoring systems for
different wall or ceiling types (e.g. wood, concrete, metal, etc.). If you are
unsure, contact a professional installer. · Televisions can be heavy. A
minimum of two people is required for a wall or ceiling mount installation.
MOVING AN OLDER TELEVISION TO A NEW PLACE IN YOUR HOME
· REMEMBER Special care should be made in the placement of older CRT/flat-
panel televisions. Many new television buyers move their older CRT/flat-panel
televisions into a secondary room after the purchase of a flat-panel
television. · NEVER place your older CRT/flat-panel television on a dresser
where children may be tempted to use the drawers to climb. · ALWAYS place your
older CRT/flat-panel television on furniture that is sturdy and appropriate
for its size and weight. · ALWAYS make sure your older CRT/flat-panel
television does not hang over the edge of your furniture.
CTA.tech
19
Supplier`s Declaration of Conformity
Trade Name Responsible Party Address
E-mail
LG LG Electronics USA, Inc. 111 Sylvan Avenue, North Building, Englewood Cliffs, NJ 07632 lg.environmental@lge.com
The model and serial number of the product are located on the back and on one side of the product. Record them below in case you ever need service.
Model Serial No.
LG Customer Information Center
For inquires or comments, visit www.lg.com or call;
1-800-243-0000 1-888-865-3026 1-888-542-2623
USA, Consumer User USA, Commercial User CANADA
Register your product Online! www.lg.com
OWNER’S MANUAL
EXTERNAL CONTROL DEVICE SETUP
Please read this manual carefully before operating the set and retain it for
future reference.
www.lg.com P/NO : MFL71445401 (1901-REV00)
ENEGNLGISH
2 KEY CODES
KEY CODES
· This feature is not available for all models.
Code (Hexa)
Function
00 CH +, PR +
01 CH -, PR –
02 Volume +
03 Volume –
06 > (Arrow Key / Right Key)
07 < (Arrow Key / Left Key)
08 Power
09 Mute
0B Input
0E SLEEP
0F TV, TV/RAD
10 – 19 * Number Key 0 – 9
1A Q.View / Flashback
1E FAV (Favorite Channel)
20 Text (Teletext)
21 T. Opt (Teletext Option)
28 Return (BACK)
30 AV (Audio / Video) Mode
39 Caption/Subtitle
40 (Arrow Key / Cursor Up)
41
V (Arrow Key / Cursor Down)
42 My Apps
43 Menu / Settings
44 OK / Enter
45 Q.Menu
4C List, –
4D PICTURE
52 SOUND
Note
R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button
R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button
R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button
R/C Button
R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button
Code (Hexa)
Function
53 List
5B Exit
60 PIP(AD)
61 Blue
63 Yellow
71 Green
72 Red
79 Ratio / Aspect Ratio
91 AD (Audio Description)
9E LIVE MENU
7A User Guide
7C Smart / Home
7E SIMPLINK
8E (Forward)
8F (Rewind)
AA Info
AB Program Guide
B0 (Play)
B1 (Stop / File List)
B5 RECENT
BA
(Freeze / Slow Play / Pause)
BB Soccer
BD (REC)
DC 3D
99 AutoConfig
9F App / *
9B TV / PC
Note
R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button
R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button
R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button
R/C Button
R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button
- Key code 4C (0x4C) is available on ATSC/ISDB models which use major/minor channel. (For South Korea, Japan, North America, Latin America except Colombia models)
ENEGNLGISH
EXTERNAL CONTROL DEVICE SETUP 3
EXTERNAL CONTROL DEVICE SETUP
· Image shown may differ from your TV.
Connect the USB to Serial(RS-232C) converter/RS-232C(Serial) input jack to an
external control device (such as a computer or an A/V control system) to
control the product’s functions externally.
Note: The type of control port on the TV can be different between model
series.
- Please be advised that not all models support this type of connectivity. * Cable is not provided.
USB to Serial(RS-232C) converter with USB Cable
USB Type
(PC)
(TV)
USB IN
· LGTV supports PL2303 chip-based (Vendor ID : 0x0557, Product ID : 0x2008)
USB to serial(RS-232C) converter which is not made nor provided by LG.
· It can be purchased from computer stores that carry accessories for IT
support professionals.
RS-232C(Serial) With RS-232C(Serial) Cable
DE9 (D-Sub 9pin) Type · You need to purchase the RS-232C (DE9, D-Sub 9pin
female-to-female type) to RS-232C(Serial) cable
required for the connection between the PC and the TV, which is specified in
the manual.
(PC)
RS-232C IN
(CONTROL & SERVICE)
(TV)
The connection interface may differ from your TV.
ENEGNLGISH
4 EXTERNAL CONTROL DEVICE SETUP
Phone jack Type
· You need to purchase the phone-jack to RS-232 cable required for the
connection between the PC and the TV, which is specified in the manual.
- For other models, connect to the USB port. * The connection interface may differ from your TV.
SERVICE ONLY
1 3
(PC)
(TV)
2
– or
(PC)
1 3
2
RS-232C IN
(CONTROL & SERVICE)
(TV)
Customer Computer
1
5
RS-232C configurations
3-Wire Configurations(Not standard)
RXD
PC 2
TV 2 TXD
TXD 3 GND 5
1 RXD 3 GND
6
9
RS-232C (Serial port)
RXD TXD GND
OR 3 2 5
D-Sub 9
2 1 3 Phone
TXD RXD GND
Set ID For Set ID number, see “Real Data Mapping” on p.6
1. Press SETTINGS to access the main menus. 2. Press the Navigation buttons to scroll to (*General About this TV or OPTION) and press OK. 3. Press the Navigation buttons to scroll to SET ID and press OK. 4. Scroll left or right to select a set ID number and select CLOSE. The adjustment range is 1-99. 5. When you are finished, press EXIT.
- (Depending on model)
ENEGNLGISH
EXTERNAL CONTROL DEVICE SETUP 5
Communication Parameters
· Baud rate : 9600 bps (UART) · Data length : 8 bits · Parity : None
Command reference list
(Depending on model)
· Stop bit : 1 bit · Communication code : ASCII code · Use a crossed (reverse) cable.
COMMAND1
COMMAND2
DATA (Hexadecimal)
COMMAND1
COMMAND2
DATA (Hexadecimal)
01. Power* k
02. Aspect Ratio
k
03. Screen Mute
k
04. Volume Mute
k
05. Volume Control
k
06. Contrast k
07. Brightness
k
08. Color/ Colour
k
09. Tint
k
10. Sharpness
k
11. OSD Select
k
12. Remote Control Lock k Mode
13. Treble k
a
00 to 01
15. Balance k
t
16. Color
c
(p.7)
(Colour)
x
u
Temperature
17. ISM
d
(p.7)
Method (Only j
p
Plasma TV)
e
00 to 01
18. Equalizer j
v
f
00 to 64
19. Energy Saving
j
q
g
00 to 64
20. Tune Command
m
a
21. Channel m
b
h
00 to 64
(Programme)
Add/Del(Skip)
i
00 to 64
22. Key
m
c
23. Control m
g
j
00 to 64
Backlight, Control Panel
Light
k
00 to 32
24. Input
x
select (Main)
b
l
00 to 01
25. 3D (Only x 3D models)
t
26. Extended x
v
m
00 to 01
3D (Only 3D
models)
27. Auto
j
u
r
00 to 64
Configure
00 to 64 00 to 64
(p.8) (p.9) 00 to 05 (p.9) 00 to 01
Key Codes 00 to 64
(p.11) (p.11) (p.12)
(p.12)
14. Bass
k
s
00 to 64
- Note: During playing or recording media, all commands except Power (ka) and Key (mc) are not executed and treated as NG. With RS232C cable, TV can communicate “ka command” in power-on or power-off status. but with USB-to-Serial converter cable, the command works only if TV is on.
ENEGNLGISH
6 EXTERNAL CONTROL DEVICE SETUP
Transmission / Receiving Protocol
Transmission [Command1][Command2][ ][Set ID][ ][Data][Cr] [Command 1] : First command to control the TV. (j, k, m or x)
[Command 2] : Second command to control the TV. [Set ID]
: You can adjust the [Set ID] to choose desired monitor ID number in option menu.
Adjustment range in TV is 1 to 99. If [Set ID] value is selected to `0′, every connected set
can be controlled.
- [Set ID] is indicated as decimal (1 to 99) on menu and as Hexadecimal (0x00 to 0x63) on
transmission/receiving protocol.
[DATA]
: To transmit command data (hexadecimal). Transmit `FF’ data to read status of command.
[Cr]
: Carriage Return – ASCII code `0x0D’
[ ]
: Space ASCII code `0x20′
OK Acknowledgement [Command2][ ][Set ID][ ][OK][Data][x] * The set transmits ACK (acknowledgement) based on this format when receiving normal data. At this time, if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the data of the PC computer.
Error Acknowledgement [Command2][ ][Set ID][ ][NG][Data][x] * The set
transmits ACK (acknowledgement) based on this format when receiving abnormal
data from non-viable functions or communication errors.
Data 00: Illegal Code
Real data mapping (Hexadecimal b Decimal)
- When you enter the [data] in hexadecimal, refer to following conversion table. * Channel Tune (ma) Command uses two-byte hexadecimal value([data]) to select channel number.
00 : Step 0 01 : Step 1 (Set ID 1) … 0A : Step 10 (Set ID 10) … 0F : Step 15 (Set ID 15) 10 : Step 16 (Set ID 16) …
32 : Step 50 (Set ID 50) 33 : Step 51 (Set ID 51) … 63 : Step 99 (Set ID 99) … C7 : Step 199 C8 : Step 200 …
FE : Step 254 FF : Step 255 … 01 00 : Step 256 … 27 0E : Step 9998 27 0F : Step 9999 …
ENEGNLGISH
EXTERNAL CONTROL DEVICE SETUP 7
- Commands may work differently depending on model and signal.
01. Power (Command: k a) To control Power *On or Off of the set.
Transmission[k][a][ ][Set ID][ ][Data][Cr]
Data 00 : Power Off
01 : *Power On
Ack [a][ ][Set ID][ ][OK/NG][Data][x] To Show TV is Power On or *Off
Transmission [k][a][ ][Set ID][ ][FF][Cr] Ack [a][ ][Set ID][ ][OK][Data][x]
- Similarly, if other functions transmit `FF’ data based on this format, Acknowledgement feedback presents status about each function.
Ack [d][ ][Set ID][ ][OK/NG][Data][x] * In case of video mute on only, TV will
display On Screen Display(OSD). But, in case of Screen mute on, TV will not
display OSD.
04. Volume Mute (Command: k e) To control volume mute on/off.
You can also adjust mute using the MUTE button on remote control. Transmission
[k][e][ ][Set ID][ ][Data][Cr] Data 00 : Volume mute on (Volume off)
01 : Volume mute off (Volume on) Ack [e][ ][Set ID][ ][OK/NG][Data][x]
02. Aspect Ratio (Command: k c) (Main Picture Size)
To adjust the screen format. (Main picture format) You can also adjust the
screen format using the Aspect Ratio in the Q.MENU. or PICTURE menu.
Transmission [k][c][ ][Set ID][ ][Data][Cr]
Data 01 : Normal screen 07 : 14:9
(4:3)
(Europe, Colombia, Mid-East,
02 : Wide screen Asia except South Korea and
(16:9)
Japan)
04 : Zoom
09 : * Just Scan
05 : Zoom 2
0B : Full Wide
(Latin America
(Europe, Colombia, Mid-
except Colombia East, Asia except South
Only)
Korea and Japan)
06 : Set by Program/ 10 to 1F : Cinema Zoom 1 to 16
Original
0c : 21:9 (Depending on model)
Ack [c][ ][Set ID][ ][OK/NG][Data][x]
- Using the PC input, you select either 16:9 or 4:3 screen aspect ratio.
- In DTV/HDMI/Component mode (high-definition), Just Scan is available.
- Full wide mode may work differently based on model and is supported for DTV fully, and ATV, AV partially.
03. Screen Mute (Command: k d) To select screen mute on/off.
Transmission [k][d][ ][Set ID][ ][Data][Cr] Data 00 : Screen mute off (Picture
on) Video mute off
01 : Screen mute on (Picture off) 10 : Video mute on
05. Volume Control (Command: k f) To adjust volume.
You can also adjust volume with the volume buttons on remote control.
Transmission [k][f][ ][Set ID][ ][Data][Cr] Data Min : 00 to Max : 64 Ack [f][
][Set ID][ ][OK/NG][Data][x] 06. Contrast (Command: k g) To adjust screen
contrast.
You can also adjust contrast in the PICTURE menu. Transmission [k][g][ ][Set
ID][ ][Data][Cr] Data Min : 00 to Max : 64 Ack [g][ ][Set ID][
][OK/NG][Data][x] 07. Brightness (Command: k h) To adjust screen brightness.
You can also adjust brightness in the PICTURE menu. Transmission [k][h][ ][Set
ID][ ][Data][Cr] Data Min : 00 to Max : 64 Ack [h][ ][Set ID][
][OK/NG][Data][x]
ENEGNLGISH
8 EXTERNAL CONTROL DEVICE SETUP
08. Color/Colour (Command: k i) To adjust the screen Color(Colour).
You can also adjust colour in the PICTURE menu. Transmission [k][i][ ][Set
ID][ ][Data][Cr] Data Min : 00 to Max : 64 Ack [i][ ][Set ID][
][OK/NG][Data][x] 09. Tint (Command: k j) To adjust the screen tint.
You can also adjust tint in the PICTURE menu. Transmission [k][j][ ][Set ID][
][Data][Cr] Data Red : 00 to Green : 64 Ack [j][ ][Set ID][ ][OK/NG][Data][x]
10. Sharpness (Command: k k) To adjust the screen sharpness.
You can also adjust sharpness in the PICTURE menu.
Transmission [k][k][ ][Set ID][ ][Data][Cr] Data Min : 00 to Max : 32
Ack [k][ ][Set ID][ ][OK/NG][Data][x]
11. OSD Select (Command: k l) To select OSD (On Screen Display) on/off when
controlling remotely.
Transmission [k][l][ ][Set ID][ ][Data][Cr]
Data 00 : OSD off
01 : OSD on
Ack [l][ ][Set ID][ ][OK/NG][Data][x]
12. Remote control lock mode (Command: k m) To lock the front panel controls
on the monitor and
remote control.
Transmission [k][m][ ][Set ID][ ][Data][Cr]
Data 00 : Lock off
01 : Lock on
Ack [m][ ][Set ID][ ][OK/NG][Data][x]
- If you are not using the remote control, use this mode. When main power is off & on (plug-off and plug-in, after 20 – 30 seconds), external control lock is released.
- In the standby mode (DC off by off timer or
ka’,
mc’ command), and if key lock is on, TV will not turn on by power on key of IR & Local Key.
13. Treble (Command: k r) To adjust treble.
You can also adjust in the AUDIO menu.
Transmission [k][r][ ][Set ID][ ][Data][Cr] Data Min : 00 to Max : 64
Ack [r][ ][Set ID][ ][OK/NG][Data][x] (Depending on model)
14. Bass (Command: k s) To adjust Bass.
You can also adjust in the AUDIO menu.
Transmission [k][s][ ][Set ID][ ][Data][Cr] Data Min : 00 to Max : 64
Ack [s][ ][Set ID][ ][OK/NG][Data][x] (Depending on model)
15. Balance (Command: k t) To adjust balance.
You can also adjust balance in the AUDIO menu. Transmission [k][t][ ][Set ID][
][Data][Cr] Data Min : 00 to Max : 64 Ack [t][ ][Set ID][ ][OK/NG][Data][x]
16. Color(Colour) Temperature (Command: x u) To adjust colour temperature.
You can also adjust
Color(Colour) Temperature in the PICTURE menu. Transmission [x][u][ ][Set ID][
][Data][Cr] Data Min : 00 to Max : 64 Ack [u][ ][Set ID][ ][OK/NG][Data][x]
17. ISM Method (Command: j p) (Only Plasma TV) To control the ISM method. You
can also adjust
ISM Method in OPTION menu. Transmission [j][p][ ][Set ID][ ][Data][Cr] Data
Min : 02: Orbiter
08: Normal 20: Color(Colour) Wash Ack [p][ ][Set ID][ ][OK/NG][Data][x]
ENEGNLGISH
EXTERNAL CONTROL DEVICE SETUP 9
18. Equalizer (Command : j v)
Adjust EQ of the set.
Transmission [j][v][ ][Set ID][ ][Data][Cr]
MSB
LSB
0000000 0
Frequency
Data
7 6 5 Frequency 4 3 2 1 0
Step
0 0 0 1st Band 0 0 0 0 0 0(decimal)
0 0 1 2nd Band 0 0 0 0 1 1(decimal)
0 1 0 3rd Band … … … … …
…
0 1 1 4th Band 1 0 0 1 1 19(decimal)
1 0 0 5th Band 1 0 1 0 1 20(decimal)
Acknowledgement [v][ ][Set ID][ ][OK/NG][Data][x]
- It depends on model, and can adjust when sound mode is EQ adjustable value.
19. Energy Saving (Command: j q)
To reduce the power consumption of the TV. You can also adjust Energy Saving
in PICTURE menu.
Transmission [j][q][ ][Set ID][ ][Data][Cr] Data 00 : Off 01 : Minimum 02 :
Medium 03 : Maximum 04 : Auto (For LCD TV / LED TV) / Intelligent sensor (For
PDP TV) 05 : Screen off
- (Depending on model)
Ack [q][ ][Set ID][ ][OK/NG][Data][x]
20. Tune Command (Command: m a)
-
This command may work differently depending on model and signal.
· For Europe, Mid-East, Colombia, Asia except South Korea and Japan Model
Select channel to following physical number.
Transmission [m][a][ ][Set ID][ ][Data 00][ ] [Data 01][ ][Data 02][Cr] -
Analog Antenna/Cable
[Data 00][Data 01] Channel Data Data 00 : High byte channel data Data 01 : Low byte channel data
– 00 00 ~ 00 C7 (Decimal : 0 ~ 199)
Data 02 : Input Source (Analog) – 00 : Antenna TV (ATV) – 80 : Cable TV (CATV) -
Digital Antenna/Cable/Satellite
[Data 00][Data 01]: Channel Data Data 00 : High Channel data Data 01 : Low Channel data
– 00 00 ~ 27 0F (Decimal: 0 ~ 9999) Data 02 : Input Source (Digital)
– 10 : Antenna TV (DTV) – 20 : Antenna Radio (Radio) – 40 : Satellite TV (SDTV) – 50 : Satellite Radio (S-Radio) – 90 : Cable TV (CADTV) – a0 : Cable Radio (CA-Radio) -
Tune Command Examples: 1. Tune to the Analog antenna (PAL) Channel 10.
Set ID = All = 00 Data 00 & 01 = Channel Data is 10 = 00 0a Data 02 = Analog Antenna TV = 00 Result = ma 00 00 0a 00
2. Tune to the digital antenna (DVB-T) Channel 01. Set ID = All = 00 Data 00 & 01 = Channel Data is 1 = 00 01 Data 02 = Digital Antenna TV = 10 Result = ma 00 00 01 10
3. Tune to the satellite (DVB-S) Channel 1000. Set ID = All = 00 Data 00 & 01 = Channel Data is 1000 = 03 E8 Data 02 = Digital Satellite TV = 40 Result = ma 00 03 E8 40
Ack [a][ ][Set ID][ ][OK][Data 00][Data 01] [Data 02][x][a][ ][Set ID][ ][NG][Data 00][x] · For South Korea, North/Latin America except Colombia Model
To tune channel to following physical/major/minor number.
Transmission [m][a][ ][0][ ][Data00][ ][Data01] [ ][Data02][ ][Data03][ ][Data04][ ][Data05][Cr] Digital channels have a Physical, Major, and Minor channel number. The Physical number is the actual digital channel number, the Major is the number that the channel should be mapped to, and the Minor is the sub-channel. Since the ATSC tuner automatically maps the channel from the Major / Minor number, the Physical number is not required when sending a command in Digital.
ENEGNLGISH
10 EXTERNAL CONTROL DEVICE SETUP
- Analog Antenna/Cable
Data 00 : Physical Channel Number – Antenna (ATV) : 02~45 (Decimal: 2 ~ 69) – Cable (CATV) : 01, 0E~7D (Decimal : 1, 14~125)
[Data 01 ~ 04]: Major/Minor Channel Number Data 01 & 02: xx (Don’t care) Data 03 & 04: xx (Don’t care) Data 05: Input Source (Analog)
– 00 : Antenna TV (ATV) – 01 : Cable TV (CATV) - Digital Antenna/Cable
Data 00 : xx (Don’t care)
[Data 01][Data 02]: Major Channel Number Data 01 : High byte Channel Data Data 02 : Low byte Channel Data
– 00 01 ~ 27 0F (Decimal: 1 ~ 9999) [Data 03][Data 04]: Minor Channel Number Data 03 : High byte Channel Data Data 04 : Low byte Channel Data
Data 05 : Input Source (Digital) – 02 : Antenna TV (DTV) Use Physical Channel Number – 06 : Cable TV (CADTV) Use Physical Channel Number – 22 : Antenna TV (DTV) Don’t Use Physical Channel Number – 26 : Cable TV (CADTV) – Don’t Use Physical Channel Number – 46 : Cable TV (CADTV) Use Physical/Major Channel Number Only (One Part Channel) – 66 : Cable TV (CADTV) Use Major Channel Number Only (One Part Channel) – 0b : Cable DTV Plus Use Physical Channel Number – 2b : Cable DTV Plus Don’t Use Physical Channel Number – 4b : Cable DTV Plus Use Physical/Major Channel Number Only (One Part Channel) – 6b : Cable DTV Plus Use Major Channel Number Only (One Part Channel)
Two bytes are available for each major and minor channel data, but usually the low byte is used alone (high byte is 0). - Tune Command Examples: 1. Tune to the Analog cable (NTSC) channel 35.
Set ID = All = 00 Data 00 = Channel Data is 35 = 23 Data 01 & 02 = No Major = 00 00 Data 03 & 04 = No Minor = 00 00 Data 05 = Analog Cable TV = 01 Total = ma 00 23 00 00 00 00 01
2. Tune to the digital antenna (ATSC) channel 30-3. Set ID = All = 00 Data 00
= Don’t know Physical = 00 Data 01 & 02 = Major is 30 = 00 1E Data 03 & 04 =
Minor is 3 = 00 03 Data 05 = Digital Antenna TV = 22 Total = ma 00 00 00 1E 00
03 22
Ack [a][ ][Set ID][ ][OK][Data 00][Data 01] [Data 02][Data 03][Data 04][Data
05] [x][a][ ][Set ID][ ][NG][Data 00][x] · For Japan Model To tune channel to
following physical/major/minor
number.
Transmission [m][a][ ][0][ ][Data00][ ][Data01] [ ][Data02][ ][Data03][
][Data04][ ][Data05][Cr] * Digital Antenna/Satellite Data 00: xx (Don’t care)
[Data 01][Data 02]: Major Channel Number Data 01: High byte Channel Data Data
02: Low byte Channel Data
– 00 01 ~ 27 0F (Decimal: 1 ~ 9999)
[Data 03][Data 04]: Minor/Branch Channel Number (Don’t care in Satellite)
Data 03: High byte Channel Data Data 04: Low byte Channel Data
Data 05 : Input Source (Digital/Satellite for Japan) – 02 : Antenna TV (DTV) –
42 : Antenna TV (DTV) Use Physical/Major Channel Number Only (One Part
Channel) – 62 : Antenna TV (DTV) Use Major Channel Number Only (One Part
Channel) – 07 : BS (Broadcasting Satellite) – 08 : CS1 (Communication
Satellite 1) – 09 : CS2 (Communication Satellite 2)
- Tune Command Examples: 1 Tune to the digital antenna (ISDB-T) channel 17-1.
Set ID = All = 00 Data 00 = Don’t know Physical = 00 Data 01 & 02 = Major is 17 = 00 11 Data 03 & 04 = Minor/Branch is 1 = 00 01 Data 05 = Digital Antenna TV = 02 Total = ma 00 00 00 11 00 01 02
ENEGNLGISH
EXTERNAL CONTROL DEVICE SETUP 11
2. Tune to the BS (ISDB-BS) channel 30. Set ID = All = 00 Data 00 = Don’t know Physical = 00 Data 01 & 02 = Major is 30 = 00 1E Data 03 & 04 = Don’t Care = 00 00 Data 05 = Digital BS TV = 07 Total = ma 00 00 00 1E 00 00 07
- This feature is varied based on the model. Ack [a][ ][Set ID][ ][OK][Data 00][Data 01] [Data 02][Data 03][Data 04][Data 05] [x][a][ ][Set ID][ ][NG][Data 00][x] 21. Channel(Programme) Add/Del(Skip) (Command: m b)
To skip current channel(programme) for next time. Transmission [m][b][ ][Set ID][ ][Data][Cr] Data 00 : Del(ATSC,ISDB)/Skip(DVB) 01 : Add
Ack [b][ ][Set ID][ ][OK/NG][Data][x] * Set the saved channel status to del(ATSC, ISDB)/ skip(DVB) or add.
22. Key (Command: m c) To send IR remote key code.
Transmission [m][c][ ][Set ID][ ][Data][Cr] Data Key code – p.2.
Ack [c][ ][Set ID][ ][OK/NG][Data][x] 23. Control Backlight (Command: m g) · For LCD TV / LED TV To control the backlight.
Transmission [m][g][ ][Set ID][ ][Data][Cr] Data Min : 00 to Max : 64
Ack [g][ ][Set ID][ ][OK/NG][Data][x] Control Panel Light (Command: m g)
· For Plasma TV To control the panel light.
Transmission [m][g][ ][Set ID][ ][Data][Cr] Data Min : 00 to Max : 64
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
24. Input select (Command: x b) (Main Picture Input)
To select input source for main picture.
Transmission [x][b][ ][Set ID][ ][Data][Cr]
Data
00 : DTV
01 : CADTV
02 : Satellite DTV
10 : ATV
ISDB-BS (Japan)
03 : ISDB-CS1 (Japan)
04 : ISDB-CS2 (Japan)
11 : CATV
20 : AV or AV1
21 : AV2
40 : Component1 60 : RGB
41 : Component2
90 : HDMI1 92 : HDMI3
91 : HDMI2 93 : HDMI4
Ack [b][ ][Set ID][ ][OK/NG][Data][x]
- This function depends on model and signal.
25. 3D(Command: x t) (only 3D models) (Depending on model)
To change 3D mode for TV.
Transmission [x][t][ ][Set ID][ ][Data 00][ ][Data 01] [ ][Data 02][ ][Data
03][Cr] (Depending on model) Data Structure [Data 00] 00 : 3D On
01 : 3D Off 02 : 3D to 2D 03 : 2D to 3D [Data 01] 00 : Top and Bottom 01 :
Side by Side 02 : Check Board 03 : Frame Sequential 04 : Column interleaving
05 : Row interleaving [Data 02] 00 : Right to Left 01 : Left to Right [Data
03] 3D Effect(3D Depth): Min : 00 – Max : 14 (transmit by Hexadecimal code)
ENEGNLGISH
12 EXTERNAL CONTROL DEVICE SETUP
- [Data 02], [Data 03] functions depend on model and signal.
- If [Data 00] is 00 (3D On), [Data 03] has no meaning.
- If [Data 00] is 01 (3D off) or 02 (3D to 2D), [Data 01], [Data 02] and [Data 03] have no meaning.
- If [Data 00] is 03 (2D to 3D), [Data 01] and [Data 02] have no meaning.
- If [Data 00] is 00 (3D On) or 03 (2D to 3D), [Data 03] works when 3D Mode (Genre) is manual only.
- All 3D pattern options ([Data 01]) may not be available according to broadcasting/video signal.
[Data 00] 00 01 02 03 [Data 01] O X X X
X : don’t care
[Data 02] O X X O [Data 03] O X X O
Ack [t][ ][Set ID][ ][OK][Data00][Data01][Data02] [Data03][x] [t][ ][Set ID][ ][NG][Data00][x]
26. Extended 3D(Command: x v) (only 3D models) (Depending on model)
To change 3D option for TV.
Transmission [x][v][ ][Set ID][ ][Data 00][ ] [Data 01][Cr] [Data 00] 3D
option 00 : 3D Picture Correction 01 : 3D Depth (3D Mode is Manual Only) 02 :
3D Viewpoint 06 : 3D Color Correction 07 : 3D Sound Zooming 08 : Normal Image
View 09 : 3D Mode (Genre)
[Data 01] It has own range for each 3D option determined by [Data 00].
-
When [Data 00] is 00 00 : Right to Left 01 : Left to Right
-
When [Data 00] is 01, 02 Data Min: 0 – Max: 14 (transmit by Hexadecimal
code) Data value range(0 – 20) converts Viewpoint range (-10 – +10) automatically (Depending on model) This option works when 3D Mode (Genre) is manual
only. -
When [Data 00] is 06, 07 00 : Off 01 : On
-
When [Data 00] is 08 00 : Revert to 3D video from 3D-to-2D converted 2D video 01 : Change 3D video to 2D video, except 2D-to-3D video
- If conversion condition doesn’t meet, command is treated as NG.
- When [Data 00] is 09
00 : Standard 02 : Cinema 04 : Manual
01 : Sport 03 : Extreme 05 : Auto
Ack [v][ ][Set ID][ ][OK][Data00][Data01][x] [v][ ][Set ID][ ][NG][Data00][x]
27. Auto Configure (Command: j u) (Depending on model)
To adjust picture position and minimize image shaking automatically. It works
only in RGB (PC) mode.
Transmission [j][u][ ][Set ID][ ][Data][Cr] Data 01 : To set Auto Configure
Ack [u][ ][Set ID][ ][OK/NG][Data][x]
References
- LG Electronics & Home Appliances | Shop Now | LG USA
- Manual-Hub.com - Free PDF manuals!
- LG Electronics & Home Appliances | Shop Now | LG USA
- Arbitration | LG USA
- Manual-Hub.com – Free PDF manuals!
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>