HiTauing 200W Aquarium Heater User Manual
- June 16, 2024
- HiTauing
Table of Contents
HiTauing 200W Aquarium Heater
AQUARIUM HEATER USER’S MANUAL
- Protecting Sleeve
- Power cord
- Power cord Plug
- OAutomatic temperature controller
- Heating light
- Constant temperature light
- ater temperature digital display
- Set temperature digital display
INSTRUCTIONS
- Before connecting the power cord of the aquarium heater to the outlet please follow our installation instructions to fix it properly in the aquarium and use it within the specified voltage range ( 110-120v) to avoid the product malfunctioning and not working properly.
- Temperature calibration.
- After power on, firstly, the red and green lights are on, 1 second later the green light is on, the red light is not on. Then the temperature display lights flashes 3 times, and the red light is on, the green light is not on.
- Finally, the temperature display screen shows the factory set temperature (821′) and enters the heating state. The red light is on, the heating is in progress; when the green light is on, it is In the state of constant temperature and stop heating.
- Temperature setting.
- After powering on, press the temperature adjustment button on the side of the temperature controller with your hand. Each time you press the thermometer will change 1 ‘F/1 ‘C (63-94’F/17-35’C cycle setting).
- Three seconds after you have set the temperature that you need, the temperature will be automatically saved.
- Please refer to the installation diagram for specific installation. If you have questions about the operation of this product, please feel free to contact us and let us do our best to help you before you return the product
PRODUCT FEATURES
-
Working mode of indicator light
When the red light is on, the heating is in progress; when the green light is on, it is in a state of constant temperature and stops heating. -
How it works
-
(D High precision imported IC chip + PIO optimization system monitoring
-
Micro software control, the working current slowly rises from O to the rated current, so that the heating body greatly improves the service life, makes the product more accurate.
-
The digital display shows the current real-time water temperature.
-
Built in temperature detector, water protector. Wlen the heating rod leaves the water surface, the green indicator light and the display screen flash together, a warning signal (E1) is issued, and the circuit is forcibly shut down.
-
Built in over temperature protection, when the water temperature exceeds 941′, it will automatically return to normal state.
-
It adopts high temperature and explosion-proof quartz tube and 304 stainless steel as heating part, with fast heating speed and heat preservation resistance. Suitable for use in seawater or freshwater tank.
INSTALLATION DIAGRAM
-
The heater should be completely immersed in the water.
-
The heater should not be exposed to the water surface, otherwise it will stop heating.
-
Please do not operate with wet hands during installation or maintenance.
-
The whole part of the fish tank heater should not be covered by filter material and debris to avoid the situation of functional failure to work properly.
PAY ATTENTION TO SAFETY
- This product is exclusively used for indoor aquariums and heating. (the whole part of the heater shall not be covered with filler materials and sundries, so as to prevent the function failure.)
- Before powering on, check whether the product is not damaged, flX it according to the regulations, and then power on to adjust the temperature. If there is damage, stop using it.
- The heater should be completely immersed in water, and the temperature controller should not be put into the water. In order to avoid damage to the normal use of the product, minors or unhealthy persons are prohibited from using the product to avoid injury ..
- It is not allowed to separate the product or carry out any structural transformation on the product to avoid product damage and personal injury to users.
- Clean or maintain the heater, turn off the power supply for 5-10 minutes before taking it out for cleaning.
WARRANTY SERVICE
As a brand seller we will be responsible for your purchase, we provide warranty service within 2 years from the date of purchase, if you have encountered any problems with the product, please do not hesitate to contact us, we will do our best to help you solve the problem.
TROUBLESHOOTING
