H3TM JRMEEW Running Man Exit Sign User Manual

H3TM JRMEEW Running Man Exit Sign

Product Information

Specifications:

electrical parts and housing; Three
years warranty for battery.

Product Usage Instructions

Installation Instructions:

1. Turn off AC power.
2. Using a flathead screwdriver, insert the blade into the two slots and pry off the front cover (see Figure 4).
3. Follow the proper mounting procedure below:
   • Wall mount:
   1. Remove the back plate from the packaging.
   2. Knock out the proper hole pattern on the back plate, including the centre hole, to mount to a standard junction box by supporting the area around the knockouts with two blocks of wood.
   3. Remove the rear cover and diffuser.
   4. Install the back plate onto the unit.
   5. Feed the AC supply leads out through the centre hole and make the proper connections (See Step 4 and Fig.6).
   • Ceiling or End Mount:
   1. Attach the crossbar to the junction box, and set the longer blade of the crossbar to touch the junction box.
4. Remove the front cover from the unit by loosening the two screws at each end of the unit (see Figure 5).
5. Remove the two screws from the top of the unit (see Figure 5).
6. Remove the bottom cover from the unit by loosening the two screws at the bottom of the unit (see Figure 5).
7. Feed the AC supply leads through the hole in the centre of the crossbar and make the proper connections (See Step 4 and Fig.6).
8. Align the keyholes on top of the unit with the screws on the crossbar (see Figure 5) and slide the unit onto the crossbar.
9. Tighten the two screws on top of the unit (see Figure 5).
10. Attach the diffuser to the front cover by sliding it into place and tightening the two screws at each end of the unit (see Figure 5).
11. Attach the front cover to the unit by sliding it into place and tightening the two screws at each end of the unit (see Figure 5).

Important Safety Instructions:

• When using electrical equipment, basic safety precautions should always be followed including the following:
  1. All servicing should be performed by qualified service personnel.
  2. Disconnect power at fuse or circuit breaker before installing or servicing.
  3. All electrical connections must be by local codes, ordinances, and the National Electric Code.
  4. Do not use outdoors.
  5. Do not let power supply cords touch hot surfaces.
  6. Do not mount near gas or electric heaters.
  7. Equipment should be mounted in locations and at heights where it will not readily be subjected to tampering by unauthorized personnel.
  8. The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.
  9. Do not use this equipment for other than intended use.
  10. Use caution when handling batteries. Battery acid can cause burns to the skin and eyes. If acid is spilled on the skin or eyes, flush the acid with fresh water and contact a physician immediately. Avoid possible shorting.
  11. Allow the battery to charge for 24 hours before first use.
• Save these instructions.

FAQ:

• Q: What is the warranty period for this product?
  A: The warranty period for the electrical parts and housing is five years, and for the battery, it is three years.

• Q: What is the IP rating of this product?
  A: The IP rating of this product is IP20.

Product Features

• SKU # 155392
• Output power: 3.5W
• CCT: 6000K-7000K
• Injection-molded thermoplastic ABS housing
• Charging Time: 24H
• Discharging Time: 90 MIN
• Input Volt: 120/347V/60Hz
• Battery: 3.6V 2000mAh Ni-Cd Battery
• IP Rating: IP20
• LED: 14 LEDS
• Certifications: UL Listed
• Warranty: (5 years warranty for the electrical parts and housing; 3 years warranty for battery)”

Specifications

Dimensions

Installation

LED Pictogram Sign

WARNING:

• Risk of Shock.
• Disconnect Power before Installation.

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should always be followed including the following:

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

1. All servicing should be performed by qualified service personnel.
2. Disconnect power at fuse or circuit breaker before installing or servicing.
3. All electrical connections must be in accordance with local codes, ordinances and the National Electric Code.
4. Do not use outdoors.
5. Do not let power supply cords touch hot surfaces.
6. Do not mount near gas or electric heaters.
7. Equipment should be mounted in locations and at heights where it will not readily be subjected to tampering by unauthorized personnel.
8. The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.
9. Do not use this equipment for other than intended use.
10. Use caution when handling batteries. Battery acid can cause burns to the skin and eyes. If acid is spilled on the skin or eyes, flush the acid with fresh water and contact a physician immediately. Avoid possible shorting.
11. Allow the battery to charge for 24 hours before first use.

SAVE THESE INSTRUCTIONS

Installation Instructions

1. Turn off AC power.

2. Using a flathead screwdriver, insert the blade into the two slots and pry off the front cover (see Figure 4).

3. Follow the proper mounting procedure below.
   Wall mount

   • Remove the back plate from the packaging.
   • Knock out the proper hole pattern on the back plate, including the centre hole, to mount to a standard junction box by supporting the area around the knockouts with two blocks of wood.
   • Remove the rear cover and diffuser.
   • Install the back plate onto the unit.
   • Feed the AC supply leads out through the centre hole and make the proper connections (See Step 4 and Fig.6). Ceiling or End Mount
   • Attach the crossbar to the junction box, and set the longer blade of the crossbar to touch the junction box.
   • Remove the mounting hole cover from the top or side of the unit depending on your mounting configuration (see Figures 2 or 3).
   • Install the canopy according to the mounting configuration (see Figure 6).
   • Feed the unit wires the through canopy hole and make the proper connections (See Step 4 and Fig.6).

4. Make the proper connections (see Figure 6):

   • For 120VAC, connect the black wire (120VAC) and white wire (neutral) to the building utility.
   • For 347VAC, connect the red wire (347VAC) and white wire (neutral) to the building utility.
   • Feed wires back into the junction box.
     CAUTION!
     Risk of electrical shock. Cap unused wires. In all cases, use suitable wire nuts rated for the applicable voltage to connect to wires.

5. For universal AC/DC models: connect wires for external DC supply (see figure 6)

   • Wire the Yellow lead to the positive(+)
   • Wire the Purple to the Negative(-)

IMPORTANT!
Electrical connections for AC and DC wires must be isolated from each other.

PACKAGE

Carton (Inch)| Qty/Carton| Net Weight/Carton| Gross Weight/Carton
---|---|---|---
14.37×9.76×6.14| 2PC| 5.07LBS| 6.17LBS

Application Picture

Warranty

Five years warranty for the electrical parts and housing; Three three-year warranty for battery.

866-786-1117 | www.BeyondLEDTechnology.com
Due to continuous product improvement, information in this document is subject to change.

References

• Wholesale Lighting Distributors & LED Lighting Solutions – Beyond LED Technology

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>