CENMATE 802RU 2 Bay RAID Hard Drive Enclosure User Manual
- June 16, 2024
- CENMATE
Table of Contents
802RU 2 Bay RAID Hard Drive Enclosure
User Manual
802RU 2 Bay RAID Hard Drive Enclosure
2 Bay RAID HDD ENCLOSURE USB 3.0 to SATA
Model : 802RU
CONTENT
2Bay 2.5 3.5 Inch Hard Drive RAID Storage
USB 3.0 Cable
Mounting screws and screw driver
User Manual
12V power Supply
OS Support
Windows 2000/ Me/ XP / Vista/ 7/ 8/ 8.1/10 and above, Mac OS 9.1/10 and Linux
CONNECTING HDD
Pull out the hard drive from the unit
Install the hard drives into the trays and put it back to the unit
Connect the USB cable to the computer
Connect the USB 3.0 connector to the unit Connect the power connector from the power adapter, and plug the power adapter to the power source Select the RAID mode when power is off. Power on the unit while holding down the reset button for 5 seconds
NOTE:
Please follow below information on how to partition and format the drives
before use
NOTE:
Data will be lost when you reset the unit
Partition and Format
- Right click on “My Computer” icon and select “Manage”. When this window appears, select “Disk Management”.
- Right click on the disk on “New Volume” and select “Initialize Disk”.
- Select the new disk to start with the configuration.
- When new disk appears, right click on it and select “News partition”.
- When the wizard window appears, click on [Next].
- Select “Primary Partition” and click on [Next].
- Select the partition size We recommend to use as maximum and click on [Next].
- Select the drive letter to assign the hard disk and click on [Next].
- Select the format settings : “FAT 32”, “DEFAULT” and Volume Label and “Perform a quick format”.
- New partition is complete and your hard disk is ready to use. Click on [Finisk].
Product Specifications
Product Specification
| RAID Level | RAID 0, RAID 1, JBOD, NORMAL |
|---|---|
| HDD Supported | Supports 2.5/3.5 inch SATA HDDs and SSDs |
| Cooling Fan | 70mm Cooling Fan |
| Interface | USB 3.0 |
| Max. Transfer Rate | 5Gb/s |
| OS Support | Windows 2000 or above, MAC OS 10.3 or above, and Linux |
| Power Adapter | 12V Power Adapter |
| Enclosure | Extruded Aluminum Case |
| Package Contents | 802RU, USB 3.0 Cable, Screws and Screws-Driver, |
| Dimension | Power Adapter and User Manual. |
205 x 130 x 80 mm
Note| HDD is not included
USB 3.0 to SATA RAID Enclosure
– USB 3.0 to SATA Enclosure
– Support 2.5/3.5 inch Hard Drive
– Support Auto Rebuild in RAID 1 Mirror Mode
– USB 3.0 (MAX 5Gbps), USB 2.0 (MAX 480Mbps)
– Convenient Tool-less Design
– Supports Windows 2000 or above, MAC OS 10.3 or above, and Linux
– Support over 2TB Hard Drives
Feature
Light 1 : Fault Indicator Light
When the hard drive is connected and working normally, the light is blue. When
the indicator light become red, it means that the hard drive failure.
Light 2: Drive Read/Write Signal Light
When this light flashing red, it means that the PC is reading/writing the data
from the hard drive. When the PC finish the process of reading/writing, the
red light will not flash and stop working,
- RAID Level : RAID 0, RAID 1, JBOD, NORMAL
- USB 3.0 (MAX 5Gbps), USB 2.0 (MAX 480Mbps)
- DC IN : 12V power supply
- Cooling Fan : 7cm Fan
- OS Support : Windows 2000 or above, MAC OS 10.3 or above, and Linux
RAID Level Setting
NORMAL
- Each works as a single hard disk, and the data is transferred individually to each hard drives.
- Both Switch 1 & 2 are off (Both Switch 1 & 2 are down).
JBOD Mode - JBOD mode (Spanning) join both hard drives capacity to provide a large volume. No performance or redundancy in this mode.
- Switch 1 is off and Switch 2 is on(Switch 1 down & Switch 2 up)
RAID 0 Mode - RAID 0 mode (Stripping) provides best performance, combining both drives for read/write to both drives.
- Switch 1 is on and Switch 2 is off(Switch 1 up & Switch 2 down).
RAID 1 Mode - RAID 1 mode (Mirroring) will provide RAID 1 protection against HDD failure
- Switch 1 and 2 are on.(Both Switch 1 & 2 are up.)
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>