LiFE ZONDA Ceiling Fan with Black Color Wooden Blades and Light 70W User Manual

Ceiling fan with black color wooden blades and light, 70W
User Manual

PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS.

Read the operating instructions carefully before putting the appliance into operation and keep the instructions, the receipt, and, if possible, the box with the internal packing. If you give this device to other people, please also pass on the operating instructions.

USER MANUAL SYMBOLS

Important information for your safety is specially marked. It is essential to comply with these instructions in order to avoid accidents and prevent damage to the machine: A WARNING: This sign warns you of dangers to your health and indicates possible injury risks.
CAUTION: This sign refers to possible hazards to the machine or other objects.

NOTE: This sign highlights tips and information

SAFETY INSTRUCTIONS

1. Use the appliance only for the purposes described in this user manual.
2. The appliance is designed exclusively for private, domestic use and for the envisaged purpose.
3. Do not use the appliance outdoors or in areas that may come into contact with water or moisture.
4. WARNING: The electrical connection and installation of the ceiling fan must be done by a certified and specialized electrician and always in accordance with national regulations for electrical installations.
5. Before using the fan, make sure that the voltage in your mains is the same as that indicated on the label of the appliance.
6. CAUTION: Before installing or repairing the ceiling fan, turn off the power to the main panel. Disconnect the fan from the power supply before installing or repairing it.
7. CAUTION: The fan must be grounded.
8. CAUTION: Do not use the appliance before assembling it.
9. Make sure the power cord is properly grounded to avoid the risk of electric shock.
10. The fan must be installed in such a way that the blades are at a height of more than 2.3 meters from the floor.
11. During installation, make sure that there is a distance of at least 15cm. from the edge of the fins to the wall and from any other object. Keep in mind that the longer this distance, the better the airflow from your fan.
12. The mounting plate must be able to support the weight of the fan in motion and a weight of at least 45kg to ensure proper placement.
13. Do not connect the fan to a dimmer switch. This can cause engine noise (even damage) and poor performance of the appliance.
14. It is not recommended to operate the ceiling fan and gas appliances in the same room at the same time.
15. Do not use the appliance unattended. If you leave the room, you should always turn off the appliance.
16. Never attempt to stop the fan blades when operating.
17. Make sure the fan is completely off before reversing the fan direction.
18. WARNING: Check all parts of the appliance before using the appliance. If there is any wear or defect do not use the appliance and contact the manufacturer.
19. WARNING: Do not operate the appliance with a damaged cord. In order to avoid the risk of an electric shock, never try to repair the appliance by yourself. Bring it to the authorized service station for repair. Use only the original spare parts.
20. This appliance may be used by persons 8 years of age and older and by persons with reduced physical, sensory or mental abilities or lack of experience and knowledge, only under the supervision or instructions of a person responsible for their safety.
21. Do not let children play with the appliance. In order to ensure your children’s safety, please keep all packaging (plastic bags, boxes, polystyrene, etc.) out of their reach.
22. WARNING: Do not allow small children to play with the foil. The danger of suffocation!
23. Cleaning and maintenance of the appliance must not be performed by children.
24. CAUTION: To avoid injury, do not place or insert any object into the fan blades when the appliance is connected to the power supply or when it is in operation. Avoid contact with any moving part.
25. Before turning on the fan, make sure all connections are stable and secure.
26. WARNING: Due to the natural movement of the fan, some connections may loosen. Check support joints, brackets, and blade fittings at least twice a year to make sure they are secure.
27. WARNING: Do not use the appliance in the presence of potentially explosive or flammable liquids or gases.
28. WARNING: For the built-in fan lampshade, use ONLY E27 LED bulbs with a maximum output of 20W each.

BATTERY SAFETY INSTRUCTIONS FOR REMOTE CONTROL

1. Different types of batteries or new and used batteries should not be used together.
2. WARNING: Remove the batteries if the remote control is not used for a long time to prevent battery leakage.
3. Do not expose the remote control to direct sunlight.
4. Always ensure that the battery compartment cover is properly closed.
5. CAUTION: Do not attempt to charge expired batteries or non-rechargeable batteries. Buy new rechargeable batteries.
6. CAUTION: Never dispose of batteries in a fire. The danger of explosion and fire!

PARTS IDENTIFICATION

1. Mounting plate
2. Fastening screws
3. Motor housing
4. Blades
5. Lampshade cover

REMOTE CONTROL

1. Medium air fan speed selection key
2. Low air fan speed selection key
3. High air fan speed selection key
4. Fan ON / OFF button
5. Lampshade ON / OFF button| 6. Timer activation key (1 hour)
7. Timer activation key (2 hours)
8. Timer activation key (4 hours)
9. Timer activation key (8 hours)
10. Indicator light
---|---

CEILING FAN INSTALLATION

1. Remove all packing materials and keep them away from babies and children.

2. Place the mounting plate in a suitable place on the ceiling (following safety instructions) and secure it with the supplied 2 screws.
   NOTE: The mounting screws included in the package are intended for concrete walls. For constructions from other materials, e.g. wooden constructions, the appropriate type of screw should be used.

3. Then join the mounting base to the motor body. Pass the motor power cords through the hole in the base, align the holes in the mounting base with the corresponding holes in the motor, place the base on the motor, and secure using 3 screws.

4. Fasten the blades to the motor body using 2 mounting screws for each blade: Insert each blade into place and align the blade holes with the corresponding holes in the motor body. Then carefully tighten the 2 screws of each blade until you are sure that the blades are locked on the motor and there is no risk of them falling out of place during the operation of the appliance.

5. Then pass the motor power cords through the hole in the lampshade holding element. Install the lampshade holding element by aligning its holes with the corresponding holes in the motor body. Then insert the three screws into the respective holes and screw them in until they lock into place.

6. Place the LED bulb in the socket (max. 20W) and then place the lampshade cover on the lampshade holding element by turning it clockwise to lock it in place.

7. Connect the motor cables to the remote control receiver and the power supply as shown in the picture below. • Brown cable – L
   • Blue cable – N
   • Green / yellow cable – Grounding
   During the connection of the wires, securely connect the copper wires of each cable and connect the terminal to the cable. Be careful to ensure that all the wires of the cable are properly inserted into the terminal and that no bare copper protrudes from the terminal, to avoid the possibility of a short circuit and electric shock.

8. Insert the remote control receiver between the cradle and the mounting bracket as shown below:

9. Place the appliance on the ceiling mount. Install the mounting bracket to the mounting base and rotate the appliance until the side holes of the mounting bracket align with the holes in the mounting bracket. Then secure by tightening the 3 screws until the fan secures with the mounting base.

USE OF REMOTE CONTROL

1. Use the remote control to set the fan speed and switch the light and the fan on/off, and set the desired operating time.
2. Open the battery compartment cover on the remote control and insert 2x AAA batteries following the correct polarity. (Batteries are not included in the package).
3. Reassemble the battery compartment cover.
4. Mark the infrared sensor with the remote control and press the desired key for the corresponding function.

NOTE: If you do not use the appliance for a long time, remove the battery from the remote control to prevent leakage of battery fluid.

USING THE APPLIANCE

1. Select the rotation speed of the fan by pressing the speed button on the remote control. The fan has 3 available operating speeds:
   • High speed
   • Medium speed
   • Low speed

2. You can switch the light on / off by pressing the corresponding key on the remote control.

3. There is a switch on the motor that regulates the direction of rotation of the fan.
   CAUTION: To avoid injury or damage to the motor, make sure that the fan is fully switched off before using the rotation switch. The switch must stay at the up or down position while the fan is working.

• Winter mode: Push the switch to the up position so that the blades move downwards the hot air trapped in the ceiling.
• Summer mode: Push the switch to the down position so that the blades create breeze cool air and better air circulation.

TIMER
The timer can be set for a certain period of time (1H, 21-1, 4H, 8H). Press the timer button to set the desired operating time.

HOW TO CHANGE THE LAMP

1. Disconnect the appliance from the power supply (from the main panel).

2. Remove the lampshade cover by turning it counterclockwise.

3. Hold the lamp firmly and remove it by turning it counterclockwise.
   CAUTION: The lamp may be very hot! Allow the bulb to cool enough before replacing it.

4. Install the new bulb and rotate it clockwise until it locks into place. Use ONLY LED lamps, up to 20W each.

5. Place the lampshade on the luminaire stand by turning it clockwise to lock it in place.

6. Connect the appliance to the power supply.

CLEANING AND MAINTENANCE

Follow the instructions to safely take care of the appliance.

1. Always make sure that the appliance is unplugged before cleaning it.
2. Wipe the body of the device with a soft damp cloth and wipe well to dry.
3. Be careful not to let the cord and the appliance come into contact with water.
4. Do not use anything abrasive that can scratch or damage the appliance. Do not use a wire brush or other abrasive utensils for cleaning. Do not use chemical solvents (such as benzene, alcohol, or gasoline) as they may cause irreversible damage to the unit.

STORAGE

1. Always unplug the appliance before storing it.
2. The appliance should be disassembled before storing.
3. Always store the appliance in a well-ventilated, humid, safe, and clean place. For better protection of the appliance, store it in its original packaging.

RECYCLING
The symbol indicates that the product should not be disposed of as waste, but should be sent to special collection facilities for recovery and recycling. Do not dispose of the appliance in ordinary bins but only on electrical appliances selected for disposal. Contact your local provider for availability. Improper disposal of electrical appliances can cause contamination of the aquifer and subsequent contamination of the food chain causing health problems.

Ionias Kalochori, 570 09 Thessaloniki, Greece,
TEL. +30 2310 700.777
e-mail: info@sun.gr 
www.life.gr Made in Chaina

Documents / Resources

| LiFE ZONDA Ceiling Fan with Black Color Wooden Blades and Light 70W [pdf] User Manual
ZONDA, Ceiling Fan, Ceiling Fan with Black Color Wooden Blades and Light 70W, ZONDA Ceiling Fan with Black Color Wooden Blades and Light 70W
---|---

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>