Povanje A001 1.6 Cub Safe Box Fireproof Waterproof For Home Instruction Manual

Povanje A001 1.6 Cub Safe Box Fireproof Waterproof For Home

COMPONENT DESCRIPTION

1. Circular Handle
2. Battery Box
3. Built-in Lamp
4. Digital Keys
5. Indicator Light
6. Emergency Keyhole
7. Removable Shelf
8. Reset Button
9. Lock Bolt

Extend 5 Years Warranty

1. Send your order number to following email support@homesafe.vip
2. Register your product warranty to activate a free extra 5 years protection

Parts list

NOTE
Please keep the emergency keys out of safe box

Instruction Video
Scan following OR code to watch the instruction video.

• https://youtu.be/CT4e0pOV2JI
• https://youtu.be/dBqz9qSsGsl
• https://youtu.be/o0-rI9xAqsA
• https://youtu.be/bljjBuPQmAQ

Initial Use

1. (Find the emergency keys in the accessories’ bag;
2. Remove the battery compartment cover
3. Insert the emergency key and turn it anticlockwise, and then clockwise turn the handle to open the door
   CAUTION: Finish operation, pull out the emergency key and keep it in a safe place.

Insert the Batteries

1. Remove the battery compartment cover.
2. Insert 4×1.5V AAA batteries into the battery box
3. Under normal condition, if the alarm beep like ” BI BI BI, BI BI BI, BI BI BI ” after you enter right password and “#” key, it means the voltage is low and you should insert new batteries

Open the Door

1. The preset code is 1234, you can set your own code
2. Touch the keypad to awake it input the correct code, the upper left indicator flash and a short beep will result from each pressing on keypad’s number
3. Press # to confirm your entering and you will hear a click and long beep from buzzer if your code is correct
4. Rotate the handle clockwise to open the door
   CAUTION: You can open the safe with preset code before setting your own code

Close the Door
Turn the handle anticlockwise to close the door

Dual Alarm System
You will hear “BI BI BI” sound from the buzzer if you enter wrong password, five times continuously wrong entries will activate the warning beep 60 seconds, at the same time the upper left indicator flash for 60 seconds.The system will be locked 60 seconds too. Touch the keypad to awake the safe,the vibration alarm will be opened after you press .The buzzer will beep 60 seconds if the safe box is subjected to violent vibration

CAUTION
The key pad would be disabled during the beeping alarm. You can only stop the beeps by opening the safe with emergency key and power-cut by  removing the battery

Set the User Code

1. Open the safe and keep it unlock until there is no light on the screen
2. Press the reset button behind the door,you will hear a short beep from buzzer,you can enter 1 – 8 code and then press “#” to confirm first time now.
3. The buzzer will sound a short beep after above step, and the keypad will flash,  you need to input the above new code and press “#” again,then you will hear a long beep from buzzer,it means your new code is successfully set.

Mute Mode

1. Touch the keypad to awake it ,and then long press “1” for 3 seconds, the upperleft indicator will light for long time,it means you set mute mode successfully
2. Under mute mode,you can touch the keypad to awake the safe ,and then long  press “1” for 3 seconds,you will hear a long beep from buzzer ,the upper left indicator will light for long time at the same time.It means you cancel the mute function successfully

Set the Administrator Code

1. Open the safe and keep it unlock until there is no light on the screen
2. Press 0 button twice, then press the reset button behind the door , you willhear a short beep from buzzer, you can enter 1 – 8 code and then press “#” to confirm first time
3. The buzzer will sound a short beep after above step, and the keypad will flash, you need to input the above new code and press “#” again,then you will hear a long beep from buzzer,it means your new code is successfully set

Restore To Factory Setting

1. Open the door, and then long press the reset button behind the door for 3 seconds,you will hear a long beep from buzzer like “BI-
2. User pasword will return to “1234”, the administrator Password will return to “123456”

Mounting

1. Drill holes for expansion bolts (or clamping screws ) in the right place

2. Use the expansion bolts (or clamping screws) to secure the case to the wall

3.  Make sure the case is mounted in place as required and then tighten all screws
   CAUTION : Use the expansion bolt when there is a concrete wall surface.

4. Use the clamping screw when there is a wooden wall surface

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>