TAKARA BELMONT Yume Noble Washing System Instruction Manual

Carrying the main body

Carrying the basin

1. Unpack the wood frame.
2. Remove the maintenance cover from the main body.
   Remove the protective tape and the Urea screws from the maintenance cover.

• Remove the maintenance cover keeping the protective tape taped to the main body cover.
  Precaution
  Do not lose the Urea screws holding down the maintenance cover.
  The Urea screws are used for holdimg down the maintenance cover  later.(see page 8)

  3. Remove the main body from the wood frame.
     Remove the screw attaching the base and skid while holding the basin. (4 points)
     Precaution
     Always have at least two people to carry the main body and hold the basin when remove the bold.

  4. When carrying the basin
     Do not take off the air mat and the protective tape.
     Carry the body by holding the edge of under the basin. Do not hold the main body cover. Always have two at least people to carry the main body. (see image on right)

Carrying the seat

1. Unpack the wood frame.

2. Remove the seat from the wood frame.
   Remove the screw attaching the foot part and skid while holding the seat. (4 points)

3. When carrying the seat
   Hold the specified points only. (see page 9)
   Always have at least two people to carry the seat. (see image on right)

Precaution

• Never hold the backrest.
  Doing so may cause incorrect operation or malfunctions in the seat.

•  Do not drag the seat.
  The feet of the seat are made of steel, so dragging it may damage the floor surface, damage the foot part, cause incorrect operation or malfunctions in the seat or toppling.

Installation of main body

• The basin or seat may not be able to be installed correctly depending on installation procedures of the main body. Always install the main body using the following procedures.

  • Main body installation procedur e

Precaution

• Always use the template to mark the floor when fixing the basin and the seat. Also, always final confirm the fixing position of the seat by using the base plate H as a guideline.
•  If the seat is to be fixed using anchor bolts, check the distance between the seat and the basin with the actual unit.

Install the basin

Installation

1. Marking the bolt (anchor) fixing position
   Use supplied template to check and make preparations for the dimensions and method for installation of the piping.

• If the power cable (for installation) is to be installed from the water supply pipe and drain pipe area, mark their position in the same way as below.
  (1) Place the supplied template on the floor and set it to the position of the water supply pipe, hot water supply pipe and drain pipe.
  (2) Mark the fixing position of the basin and seat bolts (anchor).
  (3) Drill out the fixing position holes for the basin bolts (anchor).
  (4) Remove the template from the floor.

  2. Attach pipe gasket
     (1) Cut a slit in the pipe gasket to suit the position of the pipes to be installed.
     (2) Peel away the sheet from the adhesive surface of the pipe gasket and stick to the floor surface.
     (3) Cut out a circle around the slit cut in the pipe gasket to suit the pipe surface, and fill in any gaps with caulking materials.
     Precaution
     • Always attach pipe gasket and apply caulking materials to the areas around the pipes so that there are no gaps, in order to prevent condensation within this product or water seeping on the floor in the event of water leaks.
     • If pipe gasket is not used, condensation may cause water to pool on the floor, structural parts may start degrading and malfunctions may occur.
     • If the power cable (for installation) is to be installed from the water supply pipe and drain pipe area, apply caulking materials to any gaps in the same way as above.

  3. Install the basin
     (1) Hold the stepped section at the bottom of the basin, align it with the hole position that was opened previously, and install the basin.
     Precaution
     Do not pull the basin when attempting to move it. Doing so may damage the floor.

• If the power cable (for installation) is being installed from the water upply pipe and drain pipe area, pass the cable through the gap in the center of the base and through to the seat side. * If the power cable (for installation) is being installed from the water supply pipe and drain pipe area, pass the cable through to the seat side. (able must be 1300 mm or longer from the installation 
  position) Precaution
  Ensure that the power cable (for installation) is not trapped by the base. Doing so may cause fires, electrocution or angled basin.
  (2) If the pipe gasket is trapped under the basin (base), move the basin away temporarily and cut the pipe gasket that is trapped.
  Precaution
  The basin may be installed at an angle, or may even topple over if the basin (base) is attached with the pipe gasket trapped underneath.
  (3) Attach the basin with bolts (anchor).
  Adjust the basin so that it is not installed at an angle.

Installation process for anchor bolts
Precaution

• The strength of the anchor bolts will be reduced if they are hammered into the hole while touching the bottom. Open up a gap.
•  When installing anchor bolts, insert them so that there is 2 to 5 mm of the threaded section of the head protruding. If the bolts are inserted with more than 5 mm protruding, the head may interfere with the cover.

1. Drill open a hole of the specified diameter and depth.
2. Remove the dust from each anchor hole by cleaning with a vacuum cleaner.
3. Insert the anchor bolt and tap it with a hammer until the center pin makes contact with the base plate.
4. Adjust the fastening strength of the nut using a wrench.

Attach piping

1. Attach drain hose to installed drain pipe
   Precaution
   • Check that the drain hose is not bent or damaged. This may affect water flow or damage the drain hose.
   • Check that the drain hose clamp is firmly fastened. If it is not fastened, water may leak or the drain hose may come loose.
   • Check that the hose is not in the shape of an S trap. An S trap can adversely affect the flow of drainage water. If the drain pipe layout causes an S trap to be formed, check the installation position of the basin body and piping dimensions, and make the necessary adjustments.

* Drain trap
If water leaks due to damage to the drain trap, contact your closest dealer or Takara Belmont directly. Attach the water supply pipe and hot water supply pipe
Precaution

• Always connect the pipe after removing all contaminants on the pipe such as dirt, sand and oil.
•  Check that the space around the pipe is completely filled with caulking materials.

1. Check that pipe installation suits product specifications (position, pipe, height) and that it matches the pipe installation diagram and template. (see page 28)
2. Attach the stop valve to the installed hot water supply pipe and installed water supply pipe. Take note of the orientation of the stop valve.
3. Bend the flexible pipe to suit the position of the filtered check valve and stop valve.
4. Insert the supplied packing to the flexible pipe and attach to the filtered check valve.
5.  Insert the supplied packing to the flexible pipe and attach to the stop valve.

Precaution

• When attaching the water supply pipe and hot water supply pipe, ensure that they do not come in contact with the basin pipes. Doing so will may cause water leaks.
•  Always attach the supplied packing. Using this product without installing the supplied packing may cause water leaks.
• Do not connect the hot water supply pipe and water supply pipe in reverse.
•  Check that water is not leaking from the joint.

Checks after installation of pipes

1. Test water flow
   Precaution
   Always test the water flow to prevent accidents during use.

• Test the water flow and inspect the following items. The hot water may be slightly tainted at the start of the water flow test, however this does not indicate any problem.

• For safety reasons, the product’s thermostat is designed so that the hot water does not exceed 53˚C.
  (if the supply pressure is the same, water is 20˚C and hot water is 60˚C)
  (1) Is there no water leaking from the pipe joints
  The pipe joints may come loose during transportation, so check the joints within the basin thoroughly.
  (2) Are the hot water supply and water supply pressures at the same, stable pressure If the pressure is not the same, see “How to adjust faulty temperature regulation” below.
  (3) Can temperature be controlled properly
  (4) Check that the shower outlet flow is sufficient, by the following as a guide for flow rate. Shower outlet flow rate
  Hot water supply pressure, water supply pressure : 0.1 MPa each
  Shower outlet temperature : 40˚C
  Dual function (shower): Approximately 10.0 L/min
  shower head (Aeration): Approximately 6.6 L/min

  2.  Clean
     After the hot water becomes clear during the water flow test, always clean the filter (within the check valve) and shower head.

Precaution
Failure to do so can result in insufficient flow rate and faulty temperature regulation.
Take care not to damage or lose the O-rings and gasket.
Remove and clean any dirt trapped within the shower head Remove and clean any dirt trapped within the filter pipe Attach the maintenance cover to the basin
Precaution
Take care not to hit or trap other parts when installing the cover.
Doing so may damage the parts and cause malfunctions.

1. Insert the maintenance cover into the main body cover.
2. Attach the cover with the screws.

(Urea screw M5 × 15, 1 pce)

• The Urea screws are held down the main body with the maintenance cover. (see page 8 and 13)
•  Attach the maintenance cover to the basin body in a position so that it is in contact with the floor.

Precaution
Attach the Urea screw by hand without using any tools. Using tools may cause damage to the plastic section. Install the seat
Installation
Precaution
Ensure that power cannot be turned on to the seat during the installation process.

1. Install base plate H to the basin
   Press the ribbed section of base plate H to the base of the basin and fasten with the screws. (M6 × 20, 2 pcs, plastic washer (10 × 6), 2 pcs)

• The plastic washers are supplied with the screws when the product is shipped. Check that the plastic washers have not come loose.

• If the power cable (for installation) is being installed from the water supply pipe and drain pipe area, pass the cable through the bottom of base plate H and through to the seat side.
  Precaution
  Ensure that the power cable (for installation) is not trapped by base plate H. Doing so may cause electrocution or an angled seat body.
  Precaution
  Always attach the plastic washers. If the washers are not attached, water may leak through, making it difficult to remove the screws.

  2. Install base plate H to the seat
     (1) Hold the specified section at the base of the seat (see page 9), press against the ribbed section of base plate H and fasten with the screws. (M6 × 15,2 pcs)
     Precaution
     • If the seat is attached using anchor bolts, check the distance between the seat and the basin with the actual unit.
     • When attaching the seat, always check that there are no large spaces due to warpage of base plate H or gaps between the floor. If the power cable (for installation) is to be installed from the water supply pipe and drain pipe area, apply caulking materials to any gaps in the same way as above.
     • Ensure that the power cable (for installation) is not trapped by the seat. Doing so may cause electrocution or an angled seat.

  3. Install the seat
     <If the power cable (for installation) is being installed from the water supply pipe and drain pipe area>
     Pass the power cable (for installation) from base plate H through the bottom of the seat base and position at the plugging point.
     <If the power cable (for installation) is being installed from the floor under the seat>
     Pass the power cable (for installation), from the floor and position at the plugging point.
     Attach the seat with bolts (anchor). (see page 15) Check that the seat and basin are set in correct direction.
     Precaution
     • The strength of the anchor bolts will be reduced if they are hammered into the hole while touching the bottom. Open up a gap.
     • When installing anchor bolts, insert them so that there is 2 to 5 mm of the threaded section of the head protruding. If the bolts are inserted with more than 5 mm protruding, the head may interfere with the cover.

Remove PP band

Remove the PP band from the seat.
Precaution

• Always remove this PP band. Operating this product with this PP band attached may cause incorrect operation or malfunctions in the seat.

• When moving the seat body at a later date
  Precaution

  • If the seat is to be moved at a later date, always attach the PP band. If this PP band is not attached, the transportation handle (see page 9) cannot be fastened, which can cause malfunctions to the seat or injury.

Fix legrest and link

< SUITE >
(1)Remove the cable ties from the legrest. Fix legrest and link
< NOBLE >
Precaution
Always remove this cable ties. Operating YUME SUITE and NOBLE with cable ties attached may cause incorrect operation or malfunctions in the seat.
(2)Remove the two screws that are temporarily fixed to the legrest.
(3)Use the screws removed in
(2) to secure the legrest and link as shown in the figure on the right.
Precaution
Securely fix the leg rest part and the link so that there is no looseness.
Failure to do so may cause an injury, damage to the device, or abnormal noise.

Wiring

1. Connect power cable
   <If connecting to a power cable (for installation) from the floor under the seat>
   <If connecting to a power cable (for installation) from the water supply pipe and drain pipe area>
   (1) Connect a power outlet to the power cable (for installation).
   (2) Insert the power plug from the seat into the power outlet.

• When connecting the power plug into the power outlet, do it at the plugging point and bring it to the top of the base. (see page 28)
  (1) Fasten the power cable attachment tools to the base with screws. (M5 × 10, 2 pcs)
  (2) Disconnect the power plug of the seat at the connector and connect the connector of the extension power cable (sold eparately) to the seat connector.
  (3) Pass the extension power cable (sold separately) through the hole in base plate U.
• The fastening methods for base plate U is outlined in number 2 below.
• Always use the extension power cables (sold separately) specified by Takara Belmont. 2. Install base plate U to base plate H
  Spread open base plate U and attach to base plate H with screws. (M5 × 14, 2 pcs)
  Precaution
  Take care not to spread open base plate U too far.
  Spreading the base plate out too far can result in the deformation and damage.
  Precaution
  When installing base plate U, ensure that the power cable (for installation) is not trapped.

Attach base cover

Precaution
Take care not to hit or trap other parts when installing the cover.
Doing so may damage the parts and cause malfunctions.

• Check that there is no damage or dirt on the cover before installing it.
  If there are any problems found in preliminary checks, contact your closest dealer or Takara Belmont directly.

  1. Remove the oil plug from the oil tank.
  2. Attach base cover L and R to the seat
     (1)Attach plate for base cover to base cover L. (M4×10, 2 pcs) (Plastic washer(10×4), 2 pcs)

Tips
If you attach the plate vertically to the end face of the cover, it will be easy to fit with the hole of the base cover R.Attach base cover L and R to the seat.
(M5×30, 4 pcs)
(Plastic washer (10×5),4 pcs)
(M4×10, 2 pcs)
(Plastic washer (10×4),2 pcs)
(M4×12, 3 pcs)

• The plastic washers are supplied with the screws when the product is shipped. Check that the plastic washers have not come loose.
  Precaution

  • Always attach the plastic washers.
    If the washers are not attached, water may leak through, making it difficult to remove the screws.

  • Take care that the main power switch is not turned on when installing the cover. If the foot control is accidentally turned on, the seat will start moving, and may cause accidents or malfunctions to the main body.

Tips
If you fix the plate while pressing the position of the arrow with the finger, the gap between the covers can be made small. (3)Attach the clips to base cover L and R in four locations. (clip, 4 pcs (2 each at the front and rear)

• Take note of the clip orientation when attaching them. Install base plate F to base plate H
  Attach base plate F to base plate H with screws. (Urea screws M6 × 12, 2 pcs, with rubber packing) *The rubber packing is supplied with the screws when the product is
  shipped. Check that the rubber packing has not come loose.
  Precaution
  Always attach the rubber packing to the Urea screws.
  Water may seek into the base plate from the screw attachment holes, causing malfunctions to the main body.
  Precaution
  Attach the Urea screw by hand without using any tools. Using tools may cause damage to the plastic section. Check operation (1) (after assembling the seat)
  Precaution
  • Check once again that the transportation bolt has been removed.
  • Check beforehand that there are no people or objects surrounding the seat.

  1. Turn the main power switch on. Press the right side ( symbol ) of the main power switch.

  2. Press the foot control and check operation of the seat. For operating procedures, see the separate “YUME ESPOIR/YUME SUITE/YUME NOBLE Instruction Manual”.

  3.  Once operation has been confirmed, check the attachment condition of the following items.

     Is there a large step or gap in the join between the covers? Is there a large gap between the cover or base plate and floor? Is the cover or base plate vibrating or resonating while operating?

  4. Hold down (pressing for one second or longer will make the unit “beep”) the foot control Seat lowering switch to raise the seat back frame.

  5.  Turn the main power switch off.

If there are problems present, check the screws used to attach the parts and reattach when necessary.

Attach backrest and seat

1. Attach backrest and seat
   (1) Insert the backrest into the supporting column in vertical state, align with the back frame and attach with screws through the attachment holes (middle). (M6 × 15, 4 pcs)
   (2) Turn the main power switch on.
   (3) Hold down (pressing for one second or longer will make the unit “beep”) the Seat lifiting switch of foot cpntrol to recline the backrest and bring the seat to its highest position.
   (4) Check the distance between the end of the seat back and basin. See “Adjusting the distance between the end of the backrest and basin” below for more nformation.
   (5) Turn the main power switch off.

Adjusting the distance between the end of the backrest and basin
Check the following with the reclined down.

1. Does the end of the backrest hit the basin?
2.  Is there a large gap between the end of the backrest and basin?

Is there a variation in the gap with each main body?
(Install the end of the backrest and basin so that the distance between  them is approximately 10 to 20 mm.) Use the following procedure if the distance between the end of the backrest and basin requires adjustment.

• To bring the end of the backrest and basin and closer together: use the attachment hole (top)
• To separate the end of the backrest and basin: use the attachment hole (bottom)

Attach the seat