amazon basics B07V3QLZ5Y No.4 Bench Hand Plane 2 Inch Blade User Guide

B07V3QLZ5Y No.4 Bench
Hand Plane 2 Inch Blade
User Guide
No.4 Bench Hand Plane – 2-Inch Blade

Important Safeguards

Read these inmuctions carriully and retain them for future use. If this tool is passed to a third party, then these instructions must be included
When using the tool, basic safety precautions should always be followed to reduce the risk of injury ncduding the following:

CAUTION
Parts of this tool are are extremely sharp. Care must be taken at all times when handling them.
To avoid injury the tool should always be held with two hands.

• This tool is not a toy. Children rust always be supervised by an adult when sing the tool
• Remain alert and use good judgment when using this tool. Do not use this tool if any way impaired by medications, alcohol, drugs or fatigue.
• Dress appropriately and remove all jewel ry, secure loose clothing and tie up long hair before you are in using this tool
• There is a risk of splintering and dust formation during woodworking. Wear appropriate
• protective clothing (e.g. work gloves, dust mask, safety glasses, etc.).
• Keep the blade sharp to avoid the plane catchi ng on material which may cause it to move in an unexpected way or cause workpiece damage.
• Always check the workpiece for any metal (nails, scre ws, staples, etc.) that could damage the cutting edge
• Make sure that the workpiece is damped or held securely.
• Do not modify the tool in any way unless instructed by this user manual.

Intended Use

• This tool is intended for woodworking, mainly for creating even and plane surfaces
• This tool is intended for household use only. It is not intended fo r commercial use.
• No liability will be accepted for damages resulting from improper use or non-compliance with th ese instructions.

Tool Overview

Before First Use

DANGAR
Keep any packaging materials away from children – these materials are a potential source of danger, e.g. suffocat ion

• Check the tool transport damages.
• Remove all the packing materials.
• Make sure the blade (E] is sharp and the sole (l) is flat before use. Sharpen the blade {E) and flatten the sole (I) if necessary (see section “Sharpening the blade” and Flattening the sole”)

Assembly/Disassembly

NOTICE

TO disassemble th e tool, follow the steps below in a reverse order.

1. Place the blade (E) onto the base (H). The flat surface of the blade has to face upwards. The blade adjustment slots (0) must fit around the depth adjustment wheels (F)
2. Place the lever cap (C) on the blade (E).
3. Tighten the clamping screw [B8]
4. Tighten the blade screw {A).

NOTICE

Do not over-tighten the damping screw (B). It should be tightened enough to secu re the blade (E) during use. Turing the depth adjustment wheel (l) should be possibl ewithout an excessive fore.

Adjustment

NOTICE

• For creating an even workpiece surface, the blade’s (E) cutting edge (K) should be parallel to the mouth opening on the sole (l].
• Ifouwant to achieve a side slope you can move one side of the blade (E} out more than the other. In that case the side protruding more from the mouth opening will cut deeper into the workpiece surface.

Tum the depth adjustment wheels (F) to adjust the depth of cut

• Turn the depth adjustment wheels (F) dodwise to move the blade in for increasing the cutting depth.
• Turn the depth adjustment wheels (F} counter-doclwise to move the blade out for  educing the cutting depth

Operation

For a secur e operation always hold the tool with one hand on the front handle (J) and the other hand on the rear handle (G)
General rules
For best results:

Move the blade {E) downwards.
Working techniques

1. Hold the tool with both hands. Put the palm of one hand on the top of the front handle [I), and firmly grab the rear handle (G] with the other hand.
2. Place the tool with it’s sole (l} on the workpiece. Push and pull along the surface of the workpiece with the rear handle (G) while pressing down hard on the front handle (}

Maintenance

De-rusting and rust protection

• Use commercially available rust leaner or citrus cleaner. Wear gloves and follow manufacturer’s deaning instructions.
• Spray the metal components. Let them stand for several minutes then, using steel wool, brass brush or toothbrush, scrub off as much of the rust as you can.
• To prevent the metal parts from rusting, keep them lubricated with a commercially available lubrication solution .

NOTICE
Same lubrication solutions may interact with the wood what may affect the look if the wood. Ask your dealer for an accurate lubrication solution.

Sharpening the blade
Use quality oil sharpening stones. Lubricate them with an accurate lubrication solution

1. Remove the blade (E) from the tool.

2. Place th e cutting edge (K] against the sharpening stone at approximately 25 angle

3. Slightly lift the blade (E) to a 30 angle

4. Pull the blad e (E) backwards to sharpen the cutting edge [K]. Repeat until sharpened.

5. Draw the sharpened cutting edge () across the corner of a scrap piece of wood to remove burr

6.  Reassemble the tool

Flattening the sole

NOTICE Make sure all parts are installed and in tension before flattening the sole (I) the blade (f] becomes flex once the parts are reinstalled to the tool Otherwise,

1. Affix a coarse sandpaper to a dead-flat surf ace, such as a granite or cast iron table.
2. Draw lines acr oss the entire sole [l] at regular intervals with a permanent marker.
3.  Holding the too l with even pressure at the fron t and back, work the sole (l) over the sandpaper.
4.  Pause periodically to check and continue until all li nes on the sole (l) fade evenly.
5. When all lines are removed , polish the sole (l) by working it over a fin e sandpa per.

Storage
Store in a cool and dry place away from children and pets, ideally in original packaging.

Specifications

Importer information

| For EU
---|---
Postal :| Amazon EU S.2 rL., 38 avenue John F. Kenedy, L-1855 Luxembourg
Business Reg.:| 134248
| For UK
Postal| Amazon EU SARL, UK Branch,
1 Pri ncipal Place, Worship St,
London EC2A 2FA, United Kingdom
Business Reg.:| BR017427

Feedback and Help
We would love to hear your feedback. To ensure we are providing the best customer experience
possible, please consider writing a custom er review.
Scan QR Code below with your phone camera or QR reader

US:

https://www.amazon.com/review/review-your-purchases/listing/?ref=HPB_UM_CR

UK amazon.co.uk/review/review-your-purchases
If you need help with your Amazon Basics product, please use the websit e or number below.
US: amazon.com/gp/help/customer/contact- us
UK: amazon.co.uk/gp/help/customer/contact- us
+1877.485-0385 (US Phone Number)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>