YUNYUE X-11 Helmet Bluetooth Headset Instruction Manual
- June 16, 2024
- YUNYUE
Table of Contents
X-11Helmet
bluetooth headset manual
Use the information
- Please read the product manual carefully, and properly kept.
- Please do not put this product in high temperature environment, there are rechargeable lithium batteries.
- Would you please give this product use the rated voltage of power supply to recharge.
- Please fasten the product host, avoid dropping lead to host and cell damage.
- Please cover this product is waterproof and dustproof cover, in order to avoid the water into the dust.
Product specification
| Bluetooth version: | 5.0 |
|---|---|
| Headset model: | X-11 |
| Charging voltage: | 5v 1A/2A |
| Charging time: | 2H |
| Standby time: | ≥300H |
| Duration: | ≈ 50H |
| Battery type: | 3.7vPolymer cell |
| Headset size: | 753520mm |
Packing list
Product introduction
Operating instructions
On/Off:
Long press the icon button for 3 seconds to turn on/off,
and prompt to turn on/off.
Volume/Song Switch:
Volume up/down: Press to increase the volume, and then press “ ” to decrease
the volume.
Song switching: Long press “ ” previous song, long press “ ” next song.
Pause/Play Song: Short press “ ” or “ ” to pause play.
Bluetoolh function:
Turn on the headphones, turn on the phone Bluetooth, search for Bluetooth
devices: X-11, click Connect.
Call function:
After connecting the Bluetooth of the phone, the earphone will automatically
announce the number when calling, and automatically answer the call after the
announcement.
Double click “ ” to switch between manual answering/automatic answering of
calls,The prompt tone “beep” indicates manualanswer, while the prompt tone
“beep beep” indicates automatic answer.
Short press to answer the call,long press “ ” or “ “to reject the call.
Double click on “ ” to call back the last contact’s phone number.
Connect two phones together:
Connect the headphones to the Bluetooth of the first phone first.
and then turn off the Bluetooth of the first phone, After connecting the
earphones to the Bluetooth of the second phone, there is no need to turn them
off and then turn on the Bluetooth of the first phone Simply click on the
device “X-11 on the interface to connect.
Activate the mobile voice AI assistant:
After connecting the Bluetooth phone, long press to start the phone voice Al
assistant (When using the smart assistant for the first time. it is important
to agree to access the phone content. otherwise it cannot be used. If there is
no prompt, do not pay attention.)
Work indicator light:
Start up and flash quickly, Bluetooth connection successful and slow flash,
pause and remain on, charge and turn on red light, and fully charge light
turns off,
Chinese and English voice switching:
When turned on, double-click “ “to switch between Chinese/English voice
prompts.
Installation steps
Half Helmet Style
-
Ear protection clip installed on the side
-
Woolen horn Velcro installationAt the location of the ear protectors on both sides Install the headphones
-
Hooked wheat Velcro Mounted on a straw
-
Mao Mian Mai Velcro Installed in a suitable position on the right side Put on the wheat
-
Hook face host Velcro Paste on the back of the host
-
Velcro installation of rough surface host In a suitable position on the left side Install the host
Full Helmet Style
-
Woolen horn Velcro Installed in the ear protection position inside Install the headphones
-
Hooked wheat Velcro Mounted on a straw
-
Mao Mian Mai Velcro Installed in a suitable position inside Put on the wheat
-
Hook face host Velcro Paste on the back of the host
-
Mao Mian Host Velcro Installationln a suitable position on the left side
-
Install the host
FCC Caution:
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>