MACHEREYNAGEL MN 919330 Heating Block User Manual
- June 16, 2024
- MACHEREYNAGEL
Table of Contents
MN 919330 Heating Block
User Manual
Technical Data
NANOCOLOR® VARIO HC| Programmable heating block for chemical-analytical
digestions ith 12 holes for test tubes with 16 mm outer diameter with
active cooling function
---|---
Display:| Coloured, backlit LCD touchscreen
Operation:| Display menu guidance via touchscreen
Temperature range:| 40–160 °C (1 °C increments)
Temperatures:| 5 pre-programmed temperatures: 70 / 100 / 120 / 148 / 160 °C 7
free memory locations for individual temperature settings
Temperature stability:| ± 1 °C (according to DIN, EN, ISO and EPA methods)
Warm-up time:| from 20 °C to 160 °C within 5 minutes
Cooling time:| from 160 °C to 50 °C within 10 minutes
Turn-off temperature:| free selection within the entire temperature range (10
°C in-
crements)
Heating times:| 4 pre-programmed heating times: 30 min, 60 min, 120 min,
cont
Time range:| 8 free memory locations for individual time settings
0h:01min–9h:59min (1 min increments)
Safety:| Replaceable safety covers as contact protection Lockable electro-
magnetic protective lids Overheating protection
Interface:| Overheating protection Bidirectional serial RS 232, USB A (master)
and USB B (slave) Allows connection of NANOCOLOR® T-Set (REF 919 917)
(optional fully automatic calibration and preparation of test certificates for
instrument control and monitoring)
Update:| Via Internet and USB stick
Power supply:| 110–230 V ~, 50 / 60 Hz
Power consumption:| 150 / 550 VA
Dimensions:| 290 x 287 x 146 mm
Weight:| approx. 3.2 kg
Marking:| CE
Warranty:| 2 years
Declaration of conformity:
These instruments conform to the following directives:
2006/95/EC – Low-Voltage Directive
2004/108/EC – EMV Directive
Operation
2.1. Initial operation
Remove the heating block and all accessories from the packing case. Place the
heating block at room temperature on a dry and level surface, protected from
direct sunlight. Connect the heating block to the mains supply and switch on
the instrument with the main switch on the back.
Info Serial number, actual software version and bootloader version are
displayed. Press the info screen to return to the start screen.
2.2. Touchscreen-Display
The heating block is equipped with an illuminated coloured touchscreen
display. The display is used by touching specific buttons. Familiarize
yourself with the functions of the touchscreen by pressing individual buttons
with your finger or a special pen. After touching a button, the relevant
function is activated. Do not use sharp or pointed instruments to operate the
touchscreen. Clean the touchscreen display with a microfibre cloth.
2.3. Program selection Selection of a pre-programmed temperature. The
temperature used last is always displayed first. Press the buttons repeatedly
to scroll through the temperatures. Only programmed temperatures are
displayed. The temperature values are always displayed in ascending order.
Selection of a pre-programmed heating time. The time used last is always
displayed first. Press the buttons repeatedly to scroll through the heating
times. Only programmed times are displayed. The time values are always
displayed in ascending order.
Start of a selected program.
While warming up, the selected temperature is flashing in the display.
When the desired temperature is reached, a signal tone sounds and the selected
time starts to run.
Enable / disable the automatic cooling function once the reaction time has
elapsed.
Open / Lock the electro-magnetic protective cover.
While warming up, the current temperature can be displayed by pressing the
button.
A running program can be stopped at any time. A program stop is triggered by
pressing the button. appears in the display.
Stop must be confirmed within 5 s by pressing the button again, otherwise the
program continues to run.
At the end of cooling, a signal tone sounds and appears in the display.
Press one of the following buttons ( ) to call up the last program again.
Graphic-mode
Press the graphic to zoom in and out.
Menu
General buttons:
Esc
Back to the main menu without confirming or saving changes.
OK
Changes are confirmed and/or saved.
Language
Select a language and confirm with .
Graphic-mode
A window is displayed to enable or disable the graphic mode .
Select the required setting and confirm with .
Temperature programming Select an empty slot by pressing . Enter the
desired temperature in the range from 40 to 160 °C and confirm with .
User defined temperatures can be deleted or edited in the same way. Pre-
programmed temperatures can not be deleted or edited.
Heating time programming Select an empty slot by pressing .= Enter the
desired heating time in the range from 0h:01min–9h:59min and confirm with .
User defined heating times can be deleted or edited in the same way. Pre-
programmed heating times can not be deleted or edited.
Date / time
Enter the time in the format hh:mm. Select the field for the date by touching.
Enter the date in the format dd-mm-20yy and confirm with .
Protective lid warning
A window is displayed to enable or disable the protective lid warning.
A warning dependent of the temperature is possible as well .
You can adjust the temperature by pressing the buttons.
Select the required setting and confirm with . Display
Press to adjust brightness , contrast and saturation to the
surrounding light conditions.
Sound
Press to adjust the sound level.
The icon in the display shows the adjusted sound level.
T–Set
Press to select the calibration mode.
The calibration mode allows you to calibrate all programmed temperatures.
After calibration, press to confirm and save the new calibration data.
Press to select the test mode.
The test mode allows you to test all programmed temperatures, the calibration
is not changed. Press to restore factory settings.
Press to start the program.
Deviations in temperature are displayed in different colors:
| Deviation | Color |
|---|---|
| < 1 °C | green |
| 1 < x < 2 °C | yellow |
| > 2 °C | red |
Press to save the calibration or test protocol on a USB stick.
System settings Once you press , a new window appears to restore the
following factory settings.
| User-defined temperatures
---|---
User-defined heating times
Display settings
Sound settings
Fan settings
Select the required setting and confirm with .
Once you press a new window appears to adjust the fan speed and its turn-off
temperature.
Confirm your selection with . Error list
A window with an error list is displayed.
Disposal in accordance with EU Directive 2002/96/CE
In compliance with local and national legal regulations (EU Directive
2002/96/CE), the MACHEREY-NAGEL company disposes old instruments free of
charge.
Note: With effect from August 2005, disposal using public waste disposal
facilities is no longer permitted. In the case of disposal, please contact
your MACHEREY-NAGEL representative.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>