Modunful Soap Dispenser-1388e1 Automatic Hand Soap Dispenser Instruction Manual
- June 16, 2024
- Modunful
Table of Contents
Modunful Soap Dispenser-1388e1 Automatic Hand Soap Dispenser
- Please read this manual carefully and use it correctly
We would like to express our respect for your choice of our products. May it bring you convenience in the future.
Function introduction
Specification
| Installation dimensions | Lll0XWl00x Hl70mm |
|---|---|
| Should the amount of | 700ml |
| Drip quantity | 0.5-lml/time |
| Material is qualitative | ABS, AS |
| Electrical source | 4pcs “AA” (The 5th battery) |
| Voltage | DC6V |
| Current | 120mA |
| Standby current | lOuA |
| Induction distance | 0-!0cm |
| Induction distance | 3.0V |
Installation diagram
Installation steps
- To install the soap dispenser firmly, use the back clip as a template to mark the wall for drilling. (figure 1)
- Drill a 6mm hole and insert the plastic bolt. (figure 2)
- Fix the clamp on the wall with two 4mm screws. (figure 3)
- Put 4 “AA” no. 5 batteries into the battery box. Please install the battery ac- cording to the icon of the battery box in correct installation will damage battery or soap dispenser.
- Place the soap dispenser in the groove of the back clamp and slide to the bottom. (figure 4)
- Open the top cover with the key that comes with the soap dispenser and pour the liquid soap into it1 cm. (figure 5)
- Lightly touch the switch on the right side twice, and the green light flashes once. The machine is started successfully. At this time, it is in the first gear. Tap the switch twice for the second time, and the switch is in second gear. When the hand is close to the sensor head, liquid will be discharged twice. Touch the switch twice for the third time and the machine will shut down.
- In standby mode, the green light flashes every 10 seconds.
- In the first use, because the soap liquid does not flow into the pipe, please try several times until the liquid is discharged.
Directions for use
- When installing the soap dispenser, please keep the space under the soap dispenser above 40cm.
- Choose an appropriate place to install soap dispenser. Do not make the machine wet or touch water.
- Do not install soap dispensers on mirrors or highly reflective surfaces. Do not install soap dispensers underwater.
- Do not use soap dispenser under strong light, strong light will damage the infrared money sensor.
- This product has low voltage warning function, when you find the LED light flashing, indicating the battery The battery is low, please replace it with a new one.
- If the soap dispenser does not work
- (1) Put your hand close to the detector.
- (2) Check your battery again.
- (3) Whether the switch is on.
- (4) Check the lower surface of the soap dispenser again. If there is a lot of light and silhouette on the lower surface, please remove the soapOr install a soap dispenser to a higher level.
- If no soap drops
- (1) If there is residual air in the infusion tube for the first time, please operate the soap dispenser several times.
- (2) In winter when the temperature is low, the liquid may condense. Please pour in some warm waterAfter waiting for several minutes, run the soap dispenser several times.
- (3) Liquid soap may not be enough.
Precautions and maintenance
- Please do not let dust fall into the soap dispenser as it may block the access if you send it Now the container is dirty or has impurities, please replace it with soap.
- Use soap dispensers frequently. If you do not use soap dispensers for a long time, the liquid soap may solidify.
- Add the liquid soap if there is almost 1cm of liquid soap left.
- Please replace the battery with a new one when the battery is used up.
- Clean soap dispenser
- (1) When not in use, please pour out the liquid soap, wipe it with a cloth and take out the following The battery.
- (2) Please do not put the soap dispenser into water to clean, because it will damage the circuit board.
- (3) Wet cloth and dry towel shall be used to clean the surface of soap dispenser, and dry towel shall be used to clean the battery box.
- (4) Do not use highly corrosive chemical solvents to clean the products, so as to avoid damage to the appearance and surface Shape.
- Please keep your warranty card to avoid losing your right to free warranty service.
- Alteration of this certificate is invalid.
- The company has the right of final interpretation of this regulation.
PRODUCT WARRANTY INSTRUCTIONS
The company ensures that the products are in compliance with relevant safety
standards and technical requirements, and that all functions of the products
can be fully displayed under normal use and maintenance. The company will
provide a one-year free warranty service for cardholders
(excluding consumables).
- Within one year from the date of purchase, any maintenance personnel of the company confirmed that: because of manufacturing Free warranty service can be obtained for the fault damage caused by technology, materials, etc.
- When warranty, should hold valid ticket and corresponding product warranty card is valid.
- Have one of the following circumstances, although in the warranty, but can not enjoy free warranty service Services. We will do our best to repair it, but we will recover part of the cost.
- (1) product damage caused by incorrect power supply.
- (2) damage caused by wrong installation.
- (3) damage caused by modification not approved by the company.
- (4) damage caused by handling.
- Free warranty only for the repair of faulty products free of charge, does not include due to repair caused by Other expenses.
- If the product is damaged beyond the free warranty period, we promise to repair it as usual, but we will Recover part costs as appropriate.
- Please use a liquid of moderate concentration. Too high a concentration may cause a slow or slow discharge No solution.
We provide quality products and services to create a healthy, harmonious and warm home for global consumers.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>