WAGNER 2361996 Extra Spray Attachment Wood and Metal Extra Large User Manual

WAGNER 2361996 Extra Spray Attachment Wood and Metal Extra Large User

Manual

General instruction

Read the operating instructions carefully beforeusing the tool and

observe the safety instructions. Keep the operating instructions in a safe place.
The Large spray attachment was developed for applying water-soluble paints and lacquers as well as paints and lacquers containing solvents.

CAUTION!

• The units may only be used with a functional valve. If paints rises in the ventilating hose (Fig. 1 A, item 12) do not operate the unit further!
Dismantle and clean the ventilating hose, valve and diaphragm and replace the diaphragm if necessary.
• Do not place the spray gun on the side.
Do not combine components from different spray The parts could be damaged.

Description (Fig. 1)

1. Gun body| 2) Needle
2. Nozzle seal| 4) Nozzle
3. Air cap| 6) Union nut
4. Material quantity regulation| 8) Trigger
5. Container seal| 10) Feed tube
6. Container| 12) Ventilating hose
7. Valve cover| 14) Diaphragm
8. O-ring|

Preparation of the Coating Material

The Large spray attachment can be used to spray paints, varnishes and glazes that are undiluted or slightly diluted. Detailed information is available in the technical data sheet of the manufacturer (à Internet download).
Stir the material up and put the required amount into the paint

Thinning recommendation

Sprayed material|
Glazes| undiluted
Wood preservatives, mordants, oils, disinfection agents, plant protective agents| undiluted
Paints containing solvents and water-soluble paints, primers, vehicle coating paints, thick-film glazes|

dilute by 5 – 10% (undiluted with Flexio)

If the convey capacity is too low, add 5 – 10% dilution step-by-step until the convey capacity fulfils your

Large spray attachment

Aligning suction tube

If the suction tube is positioned correctly, the container contents can be sprayed without almost any residue.
When spraying horizontal surfaces, turn suction tube forward. (Fig. 2, A) When spraying objects overhead, turn suction tube back. (Fig. 2, B)

Adjusting the material quantity (fig. 3)

Very high quantities can be processed with this attachment. To prevent paint runs on the object, first adjust the paint quantity by spraying onto a piece of card or paper from the same spraying distance.
Set the material volume by turning the regulator on the trigger guard of the spray gun.

Selecting the spray setting

WARNING! Danger of injury! Never pull the trigger guard while adjusting

the air cap.
With the union nut (fig. 4, 6) slightly unscrewed, turn the air cap (5) to the desired spraysetting position (arrow). Then tighten the union nut.

Fig. 5 A = vertical flat jet         à       for horizontal surfaces
Fig. 5 B = horizontal flat jet    à        for vertical surfaces
Fig. 5 C = circular jet                à       for corners, edges and hard-to-reach surfaces

Interruption of Work

When processing 2-component varnishes, clean the device immediately.

Shutting down and cleaning

• Switch the unit off. Vent the container in case of longer breaks and after the work has been This can be done by briefly turning open and then closing the container or by pulling the trigger guard and letting the paint into the original paint container.
• Screw of the container and empty Pull out the suction tube with container seal.
• Preclean the container and feed tube with a brush. Clean the ventilating bore (Fig. 1, C).
• Pour water or solvent into the

Do not use flammable materials for cleaning purposes.

• Screw the container tightly onto the spray

• Spray the water or solvent into a container or a

• Repeat the above procedure until the water or solvent emerging from the nozzle is

• Turn off the machine and remove the

CAUTION! Never clean seals, diaphragm and nozzle or air holes of the

spray gun with metal objects. The ventilation hose and diaphragm are only solvent- resistant to a limited extent. Do not immerse in solvent, only wipe.

• Pull the ventilating hose (Fig. 1 A, 12) at the top from the gun Screw off the valve cover (13). Remove the diaphragm (14). Clean all the parts carefully.
• Unscrew the union nut and remove the air cap and nozzle. Clean the air cap, nozzle seal and nozzle with a brush and solvent or

Assembly

The unit may only be operated with an integer diaphragm (Fig. 1A, 14).

• Place the diaphragm (Fig. 1A, 14) with the pin facing upwards on the bottom section of the Also see the marking on the gun body.
• Place on the valve cover (Fig. 1A, 13) and screw it
• Place the ventilating hose (Fig. 1A, 12) on the valve cover and on the nipple at the gun
• Push the nozzle seal (Fig. 1B, 3) over the needle (2); the groove (slot) should point towards
• Put the nozzle (Fig. 1B, 4) onto the gun body and find the correct position by turning
• Put the air cap (Fig. 1, 5) onto the nozzle (4) and tighten it using the union nut (6).
• Place the container seal from below on the suction tube and slide it over the collar, while turning the container seal
• Insert the suction tube with container seal in the gun

Spare Parts List (Fig. 1)

Pos.| Designation| Order No.
3| Nozzle seal| 0417 706
4| Nozzle (2.5 mm)| 2362 878
5| Air cap

Australia (AUS) version order no. in brackets

| 2362 877

AUS (2361 747)

6| Union nut| 2362 873
9| Container seal| 2323 039
10| Feed tube| 2362 876
11| Container 1400 ml with cover| 0417 921
12,13,14| Ventilating hose, valve cover, diaphragm| 2304 027
15| O-ring| 2362 875

**The CLICK &PAINT SYSTEM with additional spray attachments and

accessories **offers the right tool for each work.

Further information about the WAGNER range

of products for renovating is available under www .wagner-group.com

Environmental protection

The appliance and accessories should be recycled in an environmentally friendly way. Do not dispose of the appliance with household waste. Support environmental protection by taking the appliance to a local collection point or obtain information from a specialist retailer.

Important Note regarding Product Liability!

Using other accessories and spare parts can lead to partial or total loss of liability and guarantee claims. With original WAGNER accessories and spare parts, you have the guarantee that all safety regulations are fulfilled.

2 years guarantee

The guarantee runs for two years, counting from the date of sale (sales slip). It covers and is restricted to free-of-charge rectification of faults which are demonstrably attributable to the use of faulty materials in manufacture, or assembly errors; or free- of-charge replacement of the defective parts. The guarantee does not cover incorrect use or commissioning or fitting or repair work which is not stated in our operating instructions. Wearing parts are also excluded from the guarantee. The guarantee excludes commercial use. We expressly reserve the right to fulfil the guarantee. The guarantee expires if the tool is opened up by persons other than WAGNER service personnel. Transport damage, maintenance work and loss and damage due to faulty maintenance work are not covered by the guarantee. Under any guarantee claim, there must be proof of purchase of the tool through submission of the original receipt. Wherever legally possible, we exclude all liability for injury, damage or consequential loss, especially if the tool has been used for a purpose other than that stated in the operating instructions, commissioned or repaired other than in accordance with our operating instructions or if repairs are performed by someone who is unqualified. We reserve the right to perform any repairs in excess of those stated in our operating instructions. In case of guarantee or repair, please refer to your point of sale.

Read More About This Manual & Download PDF:

References

• Group Publishing
• WAGNER Group for industry, craftsmen & do-it-yourselfers | WAGNER

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>