WAGNER 2362014 Wood and Metal Extra Brilliant Instruction Manual

: June 16, 2024
: Wagner

Table of Contents

2362014 Wood and Metal Extra Brilliant
General instruction
Preparing the Coating Material
Interruption of Work
Shutting down and cleaning
Assembly
Documents / Resources

2362014 Wood and Metal Extra Brilliant
Instruction Manual

2362014 Wood and Metal Extra Brilliant

WAGNER 2362014 Wood and Metal Extra Brilliant WOOD & METAL EXTRA **BRILLIANT**

General instruction

Read the operating instructions carefully before using the tool and observe the safety instructions. Keep the operating instructions in a safe place. The safety instructions for the basic unit apply to this Brilliant spray attachment.
The Brilliant spray attachment was developed for applying water-soluble paints and lacquers as well as paints and lacquers containing solvents.
The optimised nozzle and air guide are a guarantee of high quality surfaces

CAUTION!

The units may only be used with a functional valve. If paints rises in the ventilating hose (Fig. 1 A, item 12) do not operate the unit further! Dismantle and clean the ventilating hose, valve and diaphragm and replace the diaphragm if necessary.
Do not place the spray gun on the side.
Do not combine components from different spray attachments.
The parts could be damaged.

Description (Fig. 1)

Gun body| 2) Needle
Nozzle seal| 4) Nozzle
Air cap| 6) Union nut
Material quantity regulation| 8) Trigger
Container seal| 10) Feed tube
Container| 12) Ventilating hose
Valve cover| 14) Diaphragm
O-ring| 16) Viscosity test cup

Preparing the Coating Material

The paints usually need to be diluted for use with the spray gun. You can find information on spray consistency for dilution on the material container or in the respective manufacturer’s data sheet (e.g. available on the Internet).
Otherwise, use the data in the viscosity table below as guide values (viscosity = consistency of the coating material).

Measuring the Viscosity (Fig. 2)

Stir the coating material thoroughly before measuring.
Dip the viscosity test cup (16) completely into the coating material.
Hold the test cup up and measure the time in seconds until the liquid empties out. Compare the measured “runout time” with the Viscosity Table.

Viscosity Table

Sprayed material| Runout Time in Seconds
| 280 W| Wood& Metal,
300 W| Wall
350 W| Universal
630 W
Thinner-soluble| primers| 25-30| 30-40| 30 – 45| 40-60
Thinner-soluble varnishes| 15-30| 20-45| 20 – 45| 30-60
Water-soluble| primers| 25-30| 30-40| 30 – 45| 40-60
Water-soluble varnishes| 20-25| 20-35| 20 – 40| 30-55
Wood preservatives, strippers, oils| undiluted
Disinfectants, plant protectants| undiluted
Automobile spray paint| 20-25| 20-35| 20 – 40| 30-55

Aligning suction tube (refer to the instructions of the basic device)
If the suction tube is positioned correctly, the container contents can be sprayed
without almost any residue.
When spraying horizontal surfaces, turn suction tube forward.
When spraying objects overhead, turn suction tube back.
Adjusting the material quantity
To prevent paint runs on the object, first adjust the paint quantity by spraying onto a piece of card or paper from the same spraying distance.
First turn the adjustment knob (Fig.1, Item 7) fully to the left (-) and then slowly increase the material quantity to the desired amount by turning it to the right (+).
For further information on setting the spray pattern and the correct spraying technique refer to the instructions of the basic device.

Interruption of Work

When processing 2-component varnishes, clean the device immediately.

Shutting down and cleaning

Please also refer to the instructions of the basic device.

Switch the unit off. Vent the container in case of longer breaks and after the work has been terminated. This can be done by briefly turning open and then closing the container or by pulling the trigger guard and letting the paint into the original paint container.
Screw of the container and empty it. Pull out the suction tube with container seal.
Preclean the container and feed tube with a brush. Clean the ventilating bore (Fig. 1 , C).
CAUTION! Never clean seals, diaphragm and nozzle or air holes of the spray gun with metal objects.
The ventilation hose and diaphragm are only solvent-resistant to a limited extent. Do not immerse in solvent, only wipe.
Pull the ventilating hose (Fig. 1 A, 12) at the top from the gun body. Screw off the valve cover (13). Remove the diaphragm (14). Clean all the parts carefully.
Unscrew the union nut and remove the air cap and nozzle. Clean the air cap, nozzle seal and nozzle with a brush and solvent or water.

Assembly

The unit may only be operated with an integer diaphragm (Fig. 1A, 14).

Place the diaphragm (Fig. 1A, 14) with the pin facing upwards on the bottom section of the valve. Also see the marking on the gun body.
Place on the valve cover (Fig. 1A, 13) and screw it closed.
Place the ventilating hose (Fig. 1A, 12) on the valve cover and on the nipple at the gun body.
Push the nozzle seal (Fig. 1B, 3) over the needle (2); the groove (slot) should point towards you.
Put the nozzle (Fig. 1B, 4) onto the gun body and find the correct position by turning it.
Put the air cap (Fig. 1, 5) onto the nozzle (4) and tighten it using the union nut (6).
Place the container seal from below on the suction tube and slide it over the collar, while turning the container seal slightly.
Insert the suction tube with container seal in the gun body.

| Spare Parts List (Fig. 1 )|
---|---|---
Pos.| Designation| Order No.
3| Nozzle seal| 417706
4| Nozzle 1,8mm| 2362929
5| Air cap
Australia (AUS) version order no. in brackets| 2362 930
AUS (2361 750)
6| Union nut| 2362873
9| Container seal| 2323039
10| Feed tube| 2362876
11| Container 600 ml with cover| 414906
12,13,14| Ventilating hose, Valve cover, Diaphragm| 2304027
15| 0-ring| 2362875
16| Viscosity test cup| 209058

The CLICK&PAINT SYSTEM with additional spray attachments and accessories offers the right tool for each work.
Further information about the WAGNER range of products for renovating is available under www.wagner-group.com
Environmental protection
The appliance and accessories should be recycled in an environmentally friendly way. Do not dispose of the appliance with household waste. Support friendly way. Do not dispose of the appliance with household waste. Support
environmental protection by taking the appliance to a local collection point or environmental protection by taking the appliance to a local collection point or obtain information from a specialist retailer.
Important Note regarding Product Liability!
Using other accessories and spare parts can lead to partial or total loss of liability and guarantee claims. With original WAGNER accessories and spare parts, you have the guarantee that all safety regulations are fulfilled.
2 years guarantee
The guarantee runs for two years, counting from the date of sale (sales slip). It covers and is restricted to free-of-charge rectification of faults which are demonstrably attributable to the use of faulty materials in manufacture, or assembly errors; or freeform-charge replacement of the defective parts. The guarantee does not cover incorrect use or commissioning or fitting or repair work which is not stated in our operating instructions. Wearing parts are also excluded from the guarantee. The guarantee excludes commercial use. We expressly reserve the right to fulfil the guarantee. The guarantee expires if the tool is opened up by persons other than WAGNER service personnel. Transport damage, maintenance work and loss and damage due to faulty maintenance work are not covered by the guarantee. Under any guarantee claim, there must be proof of purchase of the tool through submission of the original receipt. Wherever legally possible, we exclude all liability for injury, damage or consequential loss, especially if the tool has been used for a purpose other than that stated in the operating instructions, commissioned or repaired other than in accordance with our operating instructions or if repairs are performed by someone who is unqualified. We reserve the right to perform any repairs in excess of those stated in our operating instructions. In case of guarantee or repair, please refer to your point of sale.

WAGNER SPRAYTECH .UK. LTD
Opus Park
Moorfield Road
GB-Guildford Surrey GU1 1SZ
T +44 (0) 1483 – 454666
F + 44 (0) 1483 – 454548
Not responsible for errors and changes.
Part. No. 2362014
10/2015_RS
© Copyright by Wagner GmbH

Documents / Resources

| WAGNER 2362014 Wood and Metal Extra Brilliant [pdf] Instruction Manual
2362014, 2362014 Wood and Metal Extra Brilliant, Wood and Metal Extra Brilliant, Metal Extra Brilliant, Extra Brilliant, Brilliant
---|---