DuraComfort DP08CL Portable Air Conditioners User Guide

Portable Air Conditioner

MODEL: DP08CL / DP08CS

Thank you for selecting our quality appliance. Please be sure to read this user manual carefully before using. Any question, please contact the professional service for help.

IMPORTANT SAFEGUARDS

• This appliance is for household use only.
• Disconnect the appliance from its power source during service and when replacing parts and cleaning.
• Please note: Check the nameplate for the type of refrigerant gas used in your appliance.
• Specific nformation regarding appliances with refrigerant gas.

The appliance s recommended not to pierce the cooling circuit of the machine. At the end of its useful ife, deliver the appliance to a special waste collection centre for disposal.
GWP(Global Warming Potential): R410A: 2088, R134a: 1430, R290: 3, R32: 675.

• This hermetically sealed system contains fluoridated greenhouse gases.
• ENVIRONMENTAL NFORMATION: This unit contains fluoridated greenhouse gases covered by the Kyoto Protocol.
• Do not use this unit for functions other than those described in this nstruction manual.
• Make sure the plug s plugged firmly and completely nto the outlet. It can result in the risk of electric shock or fire.
• Do not plug other appliances into the same outlet, it can result in the risk of electric shock.
• Do not disassemble or modify the appliance or the power cord, it can result n the risk of electric shock or fire. All other services should be referred to a qualified technician.
• Do not place the power cord or appliance near a heater, radiator, or other heat source. It can result in the risk of electric shock or fire.
• This unit s equipped with a cord that has a earthed wire connected to an earthed pin or grounding tab. The plug must be plugged nto a socket that s properly installed and earthed. Do not under any circumstances cut or remove the earthed pin or grounding tab from this plug.
• The unit should be used or store in such a way that it s protected from moisture e.g. condensation, splashed water, etc. Unplug unit mmediately if this occurs.
• Always transport your appliance in a vertical position and place on a stable, evel surface during use.
• If the unit s transported laying on its side t should be stood up and left unplugged for 6 hours.
• Always use the switch on the control panel or remote controller to turn the unit off, and do not start or stop operation by plugging in or unplugging the power cord. t can result in the risk of electric shock.
• Do not touch the buttons on the control panel with your wet and damp fingers.
• Do not use hazardous chemicals to clean or come into contact with the unit. To prevent damage to the surface finish, use only a soft cloth to clean the appliance. Do not use wax, thinner, or a strong detergent. Do not use the unit in the presence of inflammable substance or vapour such as alcohol, insecticides, gasoline, etc.
• If the appliance is making unusual sounds or is emitting smoke or an unusual odor, unplug it immediately.
• Do not clean the unit with water. Water can enter the unit and damage the insulation, creating a shock hazard. If water enters the unit, unplug it immediately and contact Customer Service.
• Utilize two or more people to lift and install the unit.
• Always grasp the plug when plugging in or unplugging the appliance. Never unplug by pulling on the cord. It can result n the risk of electrical shock and damage.
• Install the appliance on a sturdy, level floor capable of supporting up to 11 Olbs(50kg). nstallation on a weak or unlevel floor can result in the risk of property damage and personal injury.
• If the appliance have the Wi-Fi function , the transmission power: ess than 20dBm, and the radio frequency range s: 2412MHz-24 72MHz.

This appliance is not intended for use by persons (including children)with reduced physical, sensory or mental capabilities.or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
If the SUPPLY CORD is damaged, t must be replaced by the manufacturer, its service agent or similarly qualified persons n order to avoid a hazard.
The appliance shall be installed in accordance with national wiring regulations.

SAFETY INFORMATION

MPORTANT SAFETY INSTRUCTIONS

WARNING When using electrical appliances, basic safety precautions should be followed, including the following

1. Should fluid from the battery accidentally get into your eyes, there is a thueat of oss of eyesight, do not rub them. Immediately.
2.  Do not put the battery in a fire, expose it to heat, dismantle or modify it. If the insulation or safety valve is damaged, the battery may leak fluid, overheat or explode.
3. Do not nsert the battery with the poles reversed. Doing so may cause some abnormality or a short and the battery may eak fluid, overheat or explode.
4. Keep the battery out of the reach of children. If the battery is swallowed, contact a pysician immediataly.
5. If the alkali fluid gets on your skin or clothes, it may burn your skin, thoroughly rinse the affected area with tap water and contact a physician mmdiately.
6. If the alkali fluid gets on your skin or clothes, it may burn your skin, thoroughly rinse the affeted area with tap water.
7. Do not mix new and old batteries or other makes of batteries. The different attributes may cause the battery to leak fluid, overheat or explode.
8. This battery was not made to be recharged. Recharging this battery may damage the insulation or internal structure and may cause the battery to leak fluid, overheat or explode.
9. Do not damage or remove the abel on the exterior of the battery. Doing so may cause the battery to short, leak fluid, overheat or explode.
10.  Do not drop, throw or expose the battery to extreme impact. Doing so may cause the battery to eak fluid, overheat or explode.
11. Do not alter the shape of the battery. If the insulation or safety valve is damaged, the battery may leak fluid, overheat or explode.
12. Immediately remove the batteries when they have lost all power. Leaving the batteries in the nuit for a long time may cause the batteries to eak fluid, overheat or explode due to gas that is generated by the batteries.
13. Remove the batteries from the unit when not using the unit for an extened period of time. The batteries may leak fluid, overheat or explode due to gas that is generated by the batteries.
14. Do not apply solder directly to the batteries. The heat may cause the batteries to leak fluid, overheat ot explode.
15. Do not get the batteies wet. Doing so may cause the batteries to overheat.
16. Star batteries someplace out of direct sunlinght where the temperature and humidity are not high. Not doing so may cause the batteries to eak fluid, overheat or explode. Also, it may cause the life and performance of the batteries to decline.
17. Follow the regulations of the local government when disposing of these batteries.
18. NEVER mix alkaline, standard (carbo-zinc), rechargeable (nickel-cadmium) batteries with this product.

SAVE THESE INSTRUCTIONS HOUSEHOLD USE ONLY

GROUNDING INSTRUCTIONS

ELECTRCAL REQUIREMENTS
In the event of malfunction or breakdown, grounding provides a path of least resistance for elecrtic current to reduce the risk of electric shock.
The appliance must be connected to a cord having an equipentgrounding conductor and a grounding plug. The plug must be plugged into an apporpriate outlet that is properly installed and grounded in accordance with all local and ordinances.

ELECTRICAL SHOCK HAZARD

• Plug into a grounded 3 prong outlet.
• Do not remove the ground prong.
• Do not use an adapter.
• Do not use an extension cord.
• Failure to follow these instructions can result in death, fire, or electrical shock.

PREFERRED GROUNDING METHOD
60Hz, 115V AC outlet protected by a 15 amp time delay fuse or circuit breaker.
INTEGRATED CIRCUIT BREAKER
For additional safety, the power cord features an integrated circuit breaker. Test and reset buttons are provided on the plug case.

The circuit breaker should be tested periodically by pressing the TEST button. If it does not cause the circuit breaker to trip, or if the RESET button will not stay engaged, unplug the appliance immediately and contact your service technician.

Note: Your appliance’s power cord and plug may differ from above the picture shows.

DANGER – lmproer connection of the equipment grounding conductor can result in a risk of electric shock. The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment grounding conductor. If repair or replacement of the Cord or plug is necessary, do not connect the equipment-grounding conductor to a live terminal. Check with a qualified electrician or service person s the grounding nstructions are not completely understood, or if in doubt as to whether the appliance is properly grounded. Do not modify the plug connected to the appliance – if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

WARNING

1. This appliance is not intended for use by persons (including children)with reduced physical, sensory or mental capabilities.or lack of experience and knowledge, unless they have been given supervision or nstruction concerning use of the appliance by a person responsible for their safety.
2. Children should be supervised to ensure that they do not play with the appliance.
3.  If the SUPPLY CORD is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons n order to avoid a hazard.
4. The appliance shall be installed in accordance with national wiring regulations.
5. Do not use means to accelerate the defrosting process or to clean, other than those recommended by the manufacturer.
6. The appliance shall be stored in a room without continuously operating ignition sources (for example: open flames, an operating gas appliance or an operating electric heater.
7. Do not pierce or burn.
8. Be aware that refrigerants may not contain an odour.

The following information is also specified in the manual for units with flammable refrigerant (R32).
[x] the maximum refrigerant charge amount (Refer to nameplate marking refrigerant amount);
[x] nformation for handling, installation, cleaning, servicing and disposal of refrigerant;
[x] a warning to keep any required ventilation openings clear of obstruction;
[x] a notice that servicing shall be performed only as recommended by the manufacturer.
[x] a warning that the appliance shall be stored in a well-ventilated area where the room size corresponds to the room area as specified for operation;
[x] a warning that the appliance shall be stored in a room without continuously operating open flames (for example an operating gas appliance) and ignition sources (for example an operating electric heater).
[x] instructions as to how the appliance s to be stored so as to prevent mechanical damage from occurring.
[x] specific information about the required qualification of the working personnel for maintenance, service and repair operations.

WARNING
The handling, installation, storage, servicing and disposal must comply with the provisions of gas-related national laws and regulations, and also national wiring regulation.
It is necessary to clear away the refrigerant in the system when maintaining or scrapping an appliance.
Ventilated area ( open doors and Windows)
Ensure that the working area is open or well ventilated before turning on the system or performing hot work. Ventilation should be maintained during operation. Ventilation quickly displaces safely diluted leaked refrigerant into the atmosphere.
Flammable refrigerant R32/R290 is used within appliance. Please follow the instructions carefully to handle, install, clean, and service the appliance to avoid damage or hazard. Do not dispose of appliance in regular trash. Contact qualified agency for proper disposal.
Servicing shall be performed only as recommended by the manufacturer.

DESCRIPTION

1. Control panel
2. Remote control receiver
3. Deflector
4. Handle (both sides)
5. Castors
6. Intake grille
7. Air outlet grille
8. Intake grille
9. Plug fixer
10. Condenser drain
11. Power cable

ACCESSORIES

NOTE: All the illustrations in this manual are for explanatory purposes only.
Your appliance may be slightly different.
Be sure all accessories are removed from the packing before use.
Caution: The unit MUST be open deflector before using!

INSTALLATION INSTRUCTIONS

EXHAUSTING HOT AIR
In the Cool Mode the appliance must be placed close to a window or opening so that the warm exhaust air can be ducted outside.
First position unit on a flat floor and make sure there’s a minimum of 18” (45cm) clearance around the unit,and is within the vicinity of a single circuit outlet power source.

1. Extend either side of the hose (Fig.1) and screw the hose inlet (Fig.2).
2. Extend the other side of the hose and screw it to the hose outlet (Fig.3).
3. Install the hose inlet into the unit (Fig.4).
4. Affix the hose outlet into the window slider kit and seal. (Fig.5 &6).

Your window slider kit has been designed to fit most standard vertical and horizontal window applications; however, it may be necessary for you to modify some aspects of the installation procedures for certain types of windows. The window slider kit can be fastened with screws.
NOTE: If the window opening is less than the minimum length of the window slider kit, cut the end without the hold in it short enough to fit in the window opening. Never cut out the hole in window slider kit.

WINDOW SLIDER KIT INSTALLATION

1. Parts:
   A) Panel
   B) Panel with one hole
   C) Panel without hole (maybe not supplied)
   D) Screw to lock window kit in place

2. Assembly:
   Slide Panel B and C into Panel A and size to window width. Windows sizes vary. When sizing the window width, be sure that the window kit assembly is free from gaps from gaps and/or air pockets when taking measurements.

3. Lock the screw into the holes that correspond With the width that your window requires to ensure that there are no gaps or air pockets in the window kit assembly after installation.

LOCATION

• The unit should be placed on a firm foundation to minimize noise and vibration. For safe and secure positioning. place the unit on a smooth, level floor strong enough to support the unit.

• The unit has casters to aid placement, but it should only be rolled on smooth, flat surfaces. Use caution when rolling on carpeted surfaces.
  Use caution and Protect floors when rolling over wood floors. Do not attempt to roll the unit over objects.

• The unit must be placed within reach of a properly rated grounded socket.

• Never place any obstacles around the air inlet or outlet of the unit.

• Allow at least 18” (45cm) of around and above space away from the wall for efficient working.

• The hose can be extended, but it is the best to keep the length to minimum required. Also make sure that the hose does not have any sharp bendor sags.

DESCRIPTION OF THE DISPLAY SCREEN
The control panel is on the top of the appliance, enables you to manage part functions without remote controller, but to fully exploit its potential, you must use the remote controller.

1. Timer button
2. Fan button
3. Increase button
4. Display screen
5. Decrease button
6. Mode button
7. ON/OFF button

A. Cool symbol
B. Dehumidify symbol
C. Fan symbol
D. Timer symbol

TURNING THE APPLIANCE ON
Plug into the mains socket, then the appliance is standby.
Press the button to make the appliance turn on. The last function active when it was turned off will appear. √ Never turn the air conditioner off by unplugging from the mains. Always press the button , then wait for a few minutes before unplugging. This allows the appliance to perform a cycle of checks to verify operation.

DESCRIPTION OF THE DISPLAY SCREEN

COOL mode
Ideal for hot muggy weather when you need to cooling and dehumidify the room.
To set this mode correctly:

• Press the “ ” button a number of times until the “Cool” symbol light appears.
• Select the target temperature18℃-32℃(64°F-90°F) by pressing the button until the corresponding  value is displayed.
• Select the required fan speed by pressing the “ ” button. Different fan speed have different function.

The most suitable temperature for the room during the summer varies from 24℃ to 27℃(75 to 81). You are recommended, however, not to set a temperature much below the outdoor temperature. This will cause unnecessary power consumption.

FAN mode
When using the appliance in this mode, the air hose does not need to be attached.
To set this mode correctly:

• Press the “ ” button a number of times until the “ Fan ” symbol appears.

• Select the required fan speed by pressing the “ ” button.
  Two speeds are available: High/Low

• If appear “ F2 ” symbol standard for high speed fan, and “ F1 ” stand for low speed fan.

As the figure below:

DRY mode
Ideal to reduce room humidity (spring and autumn, damp rooms rainy periods, etc).
Before using the dry mode, the appliance should be prepared in the same way as for cool mode, with the air exhaust hose attached to enable the moisture to be discharged outside.

To set this mode correctly:

• Press the “ ” button a number of times until the “ Dry ” symbol light appears, the screen will appear “ ”;
• In this mode, fan speed is selected automatically by the appliance.

SETTING THE TIMER
This timer can be used to delay the appliance start up or shutdown, this avoids wasting electricity by optimizing operating periods.

Programming start up

• Turn on the appliance, choose the mode you want, for example Dehumidify mode, high fan speed. Turn off the appliance.
• Press the “ ” button, the screen starts to flash, press the to adjust the set time from 0.5-24 hours.
• In 5 seconds without the operation, the timer start function, then the “Timer” symbol lights.
• Press the “ ” button again to cancel the Timer, and the “Timer” symbol disappear.

Programming shut down

• When the appliance is running, press the “ ” button, the screen starts to flash.
• Press the to adjust the set time from 0.5-24 hours.
• In 5 seconds without the operation, the timer start function, then the “Timer” symbol lights.
• Press the “ ” button again to cancel the Timer, and the “Timer” symbol disappear.

SWITCH THE UNIT OF TEMPERATURE
When the appliance is running, hold on “ ” button together 3 seconds by the same time, then you can change the unit of temperature.
For example:
Before change, in cool mode, the screen display like fig1.
After change, in cool mode, the screen display like fig2.

The following functions below are optional. Please refer to the real object, just because these functions only belong to some model.

SELF-DIAGNOSIS
The appliance has a self-diagnosis system to identify a number of malfunctions.
Error messages are displayed on the appliance display.

authorize service center.
FULL TANK (safety tank full)| Empty the internal safety tank, following the instructions in the “End of season operations” paragraph.

REMOTE CONTROL MANUAL

Point the remote control at the receiver on the appliance.
The remote control must be no more than 7 meters away from the appliance (without obstacles between the remote control and the receiver).
The remote control must be handled with extreme care. Do not drop it or expose it to direct sunlight or sources of heat.
 If the remote control do not work, please try to take out the battery, and put it back again.

INSERTING OR REPLACING THE BATTERIES

• Remove the cover on the rear of the remote control;
• Insert two “AAA” 1.5V batteries in the correct position (see instructions inside the battery compartment);
• Put the cover back to the remote control

NOTE:
√ If the remote control unit is replaced or disposed of, the batteries must be removed and discarded in accordance with current legislation as they are harmful to the environment.
√ Do not mix old and new batteries. Do not mix alkaline, standard (carbon- zinc) or rechargeable (nickel-cadmium) batteries.
√ Batteries may explode or leak if exposed to open flames. Dispose of batteries accordingly.
√ If the remote control is not being used for extended periods of time (winter storage), remove the batteries and store in a cool, dry location.

COOL mode
Ideal for hot muggy weather when you need to cooling and dehumidify the room.
To set this mode correctly:

• Press the “ ” button a number of times until the “Cool” symbol light appears.
• Select the target temperature 64℉-90℉ (18℃-32℃) by pressing the “ ∧ ” or “ ∨ ” button until the corresponding value is displayed.
• Select the required fan speed by pressing the “ ” button. Different fan speed have different function.

The most suitable temperature for the room during the summer varies from 75℉ – 81℉ (24℃ – 27℃). You are recommended, however, not to set a temperature much below the outdoor temperature. The fan speed difference is more noticeable when the appliance is under FAN mode but may not be noticeable under COOL mode.

HEAT mode
“* “means only the heat pump model have this function.
If the appliance is cooling only model, when choose the heat mode, appliance will turn to FAN mode.

FAN mode
When using the appliance in this mode, the air hose does not need to be attached.

• Press the “ ” button a number of times until the “Fan” symbol light appears.

• Select the required fan speed by pressing the “ ****” button.
  Two speeds are available: High/Low

• If appear “ F2 ” symbol standard for high speed fan, and “ F1 ” stand for low speed fan.

As the figure below:

DRY mode
Ideal to reduce room humidity (spring and autumn, damp rooms rainy periods, etc).
In dry mode, the appliance should be prepared in the same way as for cool mode, with the air exhaust hose attached to enable the moisture to be discharged outside.

To set this mode correctly:

• Press the “ ****” button a number of times until the “Dry” symbol light appears, the screen will appear “ ”；
• In this mode, fan speed is selected automatically by the appliance and default low peed fan.

SMART mode
This function don’t use for this series mode, when choose this function, the appliance will turn to FAN mode.

SWING function
NOTE: This serial unit have no auto swing function.

SLEEP function
This function is useful for the night as it gradually reduces operation of the appliance.
To set this function correctly:

• Select the cool or heat mode as described above.
• Press the “ ” button.

The appliance operates in the previously selected mode.
When you choose the sleep function, the screen will reduce the brightness，and the fan speed is low.

The SLEEP function maintains the room at optimum temperature without excessive fluctuations in either temperature or humidity with silent operation.
Fan speed is always at Low, while room temperature and humidity vary gradually to ensure the most comfortable.
When in COOL mode, the selected temperature will increase by 1℃(1℉) per hour in a 2 hour period. This new temperature will be maintained for the next 6 hours.
Then the appliance turn it off.
The SLEEP function can be canceled at any time during operation by pressing the “Sleep”, “Mode” or “fan speed” button.
In DRY mode, SLEEP function is still available.

SETTING THE TIMER

• This timer can be used to delay the appliance start up or shutdown, this avoids wasting electricity by optimizing operating periods.

Programming start up

• Turn on the appliance, choose the mode you want, for example Dehumidify mode, high fan speed. Turn off the appliance.
• Press the “ ” button , the screen starts to flash, press the “ ” to adjust the set time from 0.5-24 hours.
• In 5 seconds without the operation, the timer start function, then the “Timer” symbol lights.
• Press the “ ” button again to cancel the Timer, and the “Timer” symbol disappear.

Programming shut down

• When the appliance is running, press the “ ****” button, the screen starts to flash.
• Press the “ ****” to adjust the set time from 0.5-24 hours.
• In 5 seconds without the operation, the timer start function, then the “Timer” symbol lights.
• Press the “ ****” button again to cancel the Timer, and the “Timer” symbol disappear.

Switch the unit of temperature
Press the “C/°F” butoon, then you can change the unit of temperature.
For example:
Before change, in cool mode, the screen display like Fig.1.
After change, in cool mode, the screen display like Fig.2.
Turbo function

• Press the button, the  symbol flash on screen,
• Press the button again to confirm, the will stop flash and show on screen, that the function is working.
• This function set the appliance directly to COOL mode with setting temperature 18°C(64°F) and High fan speed in order to reach low temperature n the shortest time.
• This function can not be set in Heat mode.
• To cancel this function, press the , the flash on screen, and then press the button again to confirm , the will stop flash and disappear from screen.
• Press other button like” ” or” “also can cancel this function.

Follow me function
This function can be activated from the remote control ONLY.
The remote control serves as a remote thermostat allowing for the precise temperature control at its location.

To activate the Follow Me function, point the remote control towards the appliance and
press the button, and then press button to until the flash on screen, and then press the button again to confirm , the will stop flash and show on screen.
The remote control will send this signal to the air conditioner every 20 minutes interval until press the Follow Me/Temp Sensing button again.
If the unit does not receive the Follow Me/Temp Sensing signal during any 25 minutes interval, the unit will exit the Follow Me/Temp Sensing mode.
To cancel this function, press the , and then press or button to until the flash on screen, and then press the ** button again to confirm , the will stop flash and disappear from screen.
CHILD LOCK function**
This function s used to prevent children from pressing remote controller carelessly or accidentally.

• Hold down the ****and V and press for more than 3 seconds to open or cancel the child lock function.
• When the child lock icon s on, pressing any button on the remote control will be invalid.

TIPS FOR CORRECT USE

To get the best from your appliance, follow these recommendations:

• Close the windows and doors in the room to be air conditioned (Fig. 11). When installing the appliance semi-permanently, you should leave a door slightly open (as little as 1 cm) to guarantee correct ventilation;
• Protect the room from direct exposure to the sun by partiallyclosing curtains and/or blinds to make the appliance much more economical to run (Fig. 12);
• Never rest objects of any kind on the appliance; (Fig. 13)
• Do not block the air inlet or outlet of the appliance. Reduced air flow will result in poor performance and could damage the unit.
• Make sure there are no heat sources in the room;
•  Never use the appliance in very damp rooms ( laundries for example ).
• Never use the appliance outdoors.
• Make sure the appliance is standing on a level surface. if necessary, place the castor locks under the front wheels.

WATER DRAINAGE METHOD

When there is excess water condensation inside the unit, the appliance stops running and shows “ ” (FULL TANK as mentioned in SELF-DIAGNOSIE). This indicates that the water condensation needs to be drained using the following procedures:

Manual Draining (fig.14)
Water may need to be drained in high humidity areas

1. Unplug the unit from power source.
2. Place a drain pan under the lower drain plug. See diagram.
3. Remove the lower drain plug.
4. Water will drain out and collect in the drain pan (maybe not supplied).
5. After the water is drained, replace the lower drain plug firmly.
6. Turn on the unit.

Continuous Draining (fig.15)
While using the unit in dehumidifier mode, continuous drainage is recommended.

1. Unplug the unit from the power source.
2. Remove the drain plug. While doing this operation some residual water may spill so please have a pan to collect the water.
3. Connect the drain hose (1/2″ or 12.7mm, maybe not supplied). See diagram.
4. The water can be continuously drained through the hose into a floor drain or bucket.
5. Turn on the unit.

NOTE:
Please be sure that the height of and section of the drain hose should not be higher than that of the drain outlet, or the water tank may not be drained. (fig.16 and fig.17)

CLEANING

Before cleaning or maintenance, turn the appliance off by pressing the button on the control panel or remote control, wait for a few minutes then unplug from the mains socket.

CLEANING THE CABINET
You should clean the appliance with a slightly damp cloth then dry with a dry cloth.

• Never wash the appliance with water. It could be dangerous.
• Never use petrol, alcohol or solvents to clean the appliance.
• Never spray insecticide liquids or similar.

CLEANING THE AIR FILTERS
To keep your appliance working efficiently, you should clean the filter every week of operation.
The filter can take out like fig below.

To avoid possible cuts, avoid contacting the metal parts of the appliance when removing or re-installing the filter.
It can result in the risk of personal injury.

Use a vacuum cleaner to remove dust accumulations from the filter. If it is very dirty, immerse in warm water and rinse a number of times. The water should never be hotter than 40℃ (104℉). After washing, leave the filter to dry then attach the intake grille to the appliance.

START-END OF SEASON OPERATIONS

START OF SEASON CHECKS
Make sure the power cable and plug are undamaged and the earth system is efficient.
Follow the installation instructions precisely.
END OF SEASON OPERATIONS
To empty the internal circuit completely of water, remove the cap.
Run off all water left into a basin. When all the water has been drained, put the cap back in place.
Clean the filter and dry thoroughly before putting back.

STRICTEST OPERATION ENVIRONMENT:
Cooling mode: 18℃-35℃ (64℉-95℉), 30%RH~90%RH

TROUBLESHOOTING

• It is not plugged into the mains
• The internal safety device has tripped| • Wait
• Plug into the mains
• Wait 30 minutes, if the problem persists, contact your service center
The appliance works for a short time only| • Here are bends in the air exhaust hose
• Something is preventing the air from being discharged| • Position the air exhaust hose correctly, keeping it as short and free of curves as possible to avoid bottlenecks
• Check and remove any obstacle obstructing air discharge
The appliance works, but does not cool the room| • Windows, doors and/or curtains open| • Close doors, windows and curtains, bearing in mind the “tips for correct use” given above
• There are heat sources in the room (oven, hairdryer, etc.)| • Eliminate the heat sources
• The air exhaust hose is detached from the appliance| • Fit the air exhaust hose in the housing at the back of the appliance
• The technical specification of the appliance is not adequate for the room in which it is located|
During operation, there is an unpleasant smell in the room| • Air filter clogged| • Clean the filter as described above
The appliance does not operate for about three minutes after restarting it| • The internal compressor safety device prevents the appliance from being restarted until three minutes have elapsed since it was last turned off| • Wait. This delay is part of normal operation
The following message appears on the display:
| •The appliance has a self- diagnosis system to identify a number of malfunctions| • See the SELF-DIAGNOSIS Chapter

WARRANTY

Dear Customer
Thank you for your purchase and for your confidence in our company. This product meets applicable safety requirements and has undergone stringent testing during manufacturing process.
However, should there occur a defect, the product or its defective part(s) (excluding accessories and consumables) will be repaired free of charge (labour and parts) within a limited period.If you have any questions, please contact us, we will provide assistance as soon as possible.

Warranty period:
Labor: 12 Months from the Date of purchase.
Parts: 12 Months from the Date of purchase.

THIS LIMITED WARRANTY DOES NOT APPLY TO:

1. Damage caused by transportation or handling.
2. Damage caused to the product by accident, vermin, ightning,winds, fire,floods,or acts of God.
3. Damages caused by operating the product in a corrosive atmosphere.
4. Repairs when your DuraComfort product is used in other than normal, single-family household use or contrary to the instructions described in the product User’s Guide.
5. Damage resulting from accident, alteration, misuse, abuse,or improper installation,repair,or maintenance. Improper repair includes the use of parts not approved or specified by DuraComfort.
6. Normal maintenance as described in the User’s Guide, such as cleaning or replacing filters,cleaning coils,etc.
7. Use of accessories or components that are not compatible with this product.
8. Products with altered or removed serial numbers.
9. Changes in the appearance of the product that do not affect product performance.

HELP
Customer service: support@duracomfort-life.com
Shenzhen TCL Dura Electronic Technology Co., Ltd.
Room 11, 1st Floor, Block A, TCL Building, No.006, Gaoxin South 1st
Road,Gaoxin Zone Community, Yuehai Subdi strict,Nanshan District,
Shenzhen, Guangdong, China

FOR MORE HELP
Customer service:
support@duracomfort-life.com

Documents / Resources

| DuraComfort DP08CL Portable Air Conditioners [pdf] User Guide
DP08CL, DP08CS, DP08CL Portable Air Conditioners, DP08CL, Portable Air Conditioners, Air Conditioners, Conditioners
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>