KUFATEC W213 Complete Set Active Parking Assistant Parktronic Installation Guide
- June 16, 2024
- KUFATEC
Table of Contents
- W213 Complete Set Active Parking Assistant Parktronic
- Product Information
- Specifications
- General Notes
- Safety Instructions
- Requirements for the Intended Use
- Assembly Instructions
- 1. Disassembly of Front Bumper
- 2. Disassembly of Engine Compartment Covering
- 3. Disassembly of Front Driver’s Side Sill Trim
- 4. Disassembly of Center Console
- 5. Disassembly of Main Unit
- 6. Disassembly of Back Seat
- 7. Disassembly of Rear Driver’s Side Covering
- 8. Disassembly of Rear Bumper
- 9. Assembly of Rear Sensors
- 10. Assembly of Front Sensors
- 11. Assembly of Sensor Holders with Adhesive Pads
- 12. Assembly/Connection of Control Unit
- 13. Cable Routing to the Rear
- 14. Cable Routing to the Front
- 15. Connection of Main Unit
- 16. Connection of EZS/EIS Control Unit
- 17. Assembly/Connection of Warning Buzzer
- 18. Connection of Ground
- 19. Connection of Parktronic Control Unit
- 20. Connection to Fuse Box
- 21. Exchange of Rear View Camera (If Installed)
- 22. Cable Routing for Rear View Camera
- 23. Assembly of Vehicle
- 24. Assembly of Park Assist Sensors
- 25. Coding Interface
- 26. Additional Vehicle Function
W213 Complete Set Active Parking Assistant Parktronic
Product Information
Specifications
-
Product Name: Complete Set Active Parking Assistant
Parktronic -
Version: v1.0 (01.02.2023)
-
Manufacturer: Kufatec GmbH & Co. KG
-
Address: Dahlienstr. 15, 23795 Bad Segeberg
-
Email: info@kufatec.de
General Notes
The Complete Set Active Parking Assistant Parktronic is a
parking assistance system designed to help drivers park their
vehicles safely and accurately. This user manual provides detailed
instructions for installing and using the product.
Safety Instructions
Please read and follow the safety instructions below before
installing or using the product:
-
Ensure the vehicle’s engine is turned off and the ignition key
is removed before starting the installation process. -
Use caution when handling the components to avoid injury or
damage. -
Do not modify or alter any components of the system.
-
Consult a professional technician if you are unsure about any
step of the installation process. -
Keep the product away from water, moisture, and extreme
temperatures.
Requirements for the Intended Use
In order to use the Complete Set Active Parking Assistant
Parktronic, the following requirements must be met:
-
A compatible vehicle model and year as specified by the
manufacturer. -
Basic knowledge of automotive electrical systems and
wiring. -
The necessary tools for installation, including screwdrivers,
pliers, and wire cutters. -
Adequate space and lighting for working on the vehicle.
Assembly Instructions
The following sections provide step-by-step instructions for
assembling the Complete Set Active Parking Assistant
Parktronic:
1. Disassembly of Front Bumper
Follow the instructions provided in section 10 of the manual to
disassemble the front bumper of your vehicle.
2. Disassembly of Engine Compartment Covering
Refer to section 11 of the manual for detailed instructions on
how to remove the covering of the engine compartment.
3. Disassembly of Front Driver’s Side Sill Trim
Section 12 of the manual provides step-by-step instructions on
how to disassemble the front driver’s side sill trim.
4. Disassembly of Center Console
Follow the instructions in section 13 of the manual to
disassemble the center console of your vehicle.
5. Disassembly of Main Unit
Refer to section 14 of the manual for detailed instructions on
how to disassemble the main unit.
6. Disassembly of Back Seat
Section 15 of the manual provides step-by-step instructions on
how to disassemble the back seat.
7. Disassembly of Rear Driver’s Side Covering
Follow the instructions in section 16 of the manual to
disassemble the covering on the rear driver’s side.
8. Disassembly of Rear Bumper
Refer to section 18 of the manual for detailed instructions on
how to disassemble the rear bumper of your vehicle.
9. Assembly of Rear Sensors
Section 19 of the manual provides step-by-step instructions on
how to assemble the rear sensors.
10. Assembly of Front Sensors
Follow the instructions in section 20 of the manual to assemble
the front sensors.
11. Assembly of Sensor Holders with Adhesive Pads
Refer to section 21 of the manual for detailed instructions on
how to assemble the sensor holders using the adhesive pads.
12. Assembly/Connection of Control Unit
Section 22 of the manual provides step-by-step instructions on
how to assemble and connect the control unit.
13. Cable Routing to the Rear
Follow the instructions in section 23 of the manual to route the
cables to the rear of the vehicle.
14. Cable Routing to the Front
Refer to section 24 of the manual for detailed instructions on
how to route the cables to the front of the vehicle.
15. Connection of Main Unit
Section 25 of the manual provides step-by-step instructions on
how to connect the main unit.
16. Connection of EZS/EIS Control Unit
Follow the instructions in section 26 of the manual to connect
the EZS/EIS control unit.
17. Assembly/Connection of Warning Buzzer
Refer to section 27 of the manual for detailed instructions on
how to assemble and connect the warning buzzer.
18. Connection of Ground
Section 28 of the manual provides step-by-step instructions on
how to connect the ground wire.
19. Connection of Parktronic Control Unit
Follow the instructions in section 29 of the manual to connect
the Parktronic control unit.
20. Connection to Fuse Box
Refer to section 30 of the manual for detailed instructions on
how to connect the product to the fuse box.
21. Exchange of Rear View Camera (If Installed)
Section 31 of the manual provides step-by-step instructions on
how to exchange the rear view camera, if installed.
22. Cable Routing for Rear View Camera
Follow the instructions in section 33 of the manual to route the
cables for the rear view camera.
23. Assembly of Vehicle
Refer to section 35 of the manual for detailed instructions on
how to assemble the vehicle after completing the installation.
24. Assembly of Park Assist Sensors
Follow the instructions in section 36 of the manual to assemble
the park assist sensors.
25. Coding Interface
Refer to section 37 of the manual for detailed instructions on
how to use the coding interface.
26. Additional Vehicle Function
Section 38 of the manual provides information on additional
functions that can be enabled for your vehicle using the
product.
Frequently Asked Questions (FAQ)
-
1. **Q: What is the purpose of the Complete Set Active
Parking Assistant Parktronic?**
A: The Complete Set Active Parking Assistant Parktronic is a
parking assistance system designed to help drivers park their
vehicles safely and accurately.
-
1. **Q: How can I obtain the necessary tools for
installation?**
A: You can purchase the necessary tools, such as screwdrivers,
pliers, and wire cutters, from automotive supply stores or online
retailers.
-
1. **Q: Can I install the Complete Set Active Parking
Assistant Parktronic on any vehicle?**
A: The product is compatible with specific vehicle models and
years as specified by the manufacturer. Please refer to the product
documentation or contact the manufacturer for compatibility
information.
-
1. **Q: Do I need professional assistance to install the
product?**
A: Basic knowledge of automotive electrical systems and wiring
is required for the installation process. If you are unsure about
any step, it is recommended to consult a professional
technician.
Installation Instructions
Complete Set Active Parking Assistant Parktronic
v1.0 (01.02.2023)
Kufatec GmbH & Co. KG – Dahlienstr. 15 – 23795 Bad Segeberg – e-mail: info@kufatec.de
1
Contents
1 Liability Exclusion
3
2 Copyright
4
3 General notes
4
4 Safety Instructions
5
5 Requirements for the intended use
5
6 How to connect a cable to another
6
7 Note Cable Inscription/Color
7
8 Assembly Instructions
8
9 Assembly Note
9
10 Disassembly front bumper
10
11 Disassembly covering engine compartment
12
12 Disassembly sill trim front driver’s side
13
13 Disassembly center console
14
14 Disassembly main unit
15
15 Disassembly back seat
16
16 Disassembly covering rear driver’s side
17
17 Disassembly fuse box trunk – Coup´e
18
18 Disassembly rear bumper
19
19 Assembly rear sensors
20
20 Assembly front sensors
21
21 Assembly sensor holders with adhesive pads
23
22 Assembly/Connection control unit
24
23 Cable routing to the rear
25
24 Cable routing to the front
26
25 Connection main unit
28
26 Connection EZS/EIS control unit
29
27 Assembly/Connection warning buzzer
30
28 Connection ground
31
29 Connection bridge Parktronic control unit
32
30 Connection fuse box
33
Kufatec GmbH & Co. KG – Dahlienstr. 15 – 23795 Bad Segeberg – e-mail: info@kufatec.de
2
31 Note exchange rear view camera (if a rear view camera is installed)
34
32 Disassembly tailgate covering – Coup´e
35
33 Cable routing rear view camera
37
34 Exchange rear view camera
38
35 Assembling the vehicle
39
36 Important Note: Assembly Park Assist Sensors
39
37 Coding interface
39
38 Additional vehicle function
39
Kufatec GmbH & Co. KG – Dahlienstr. 15 – 23795 Bad Segeberg – e-mail: info@kufatec.de
3
8 Assembly Instructions
The following illustration shows the cable routing as well as the position of
the individual components.
3
12
4
7
5,6
8
2 1 1
3
8 8
68
7
1
1
2
4
8
5
8
8
Figure 3: Vehicle overview
· 1 Front Park Pilot sensors · 2 Park Assist sensors (brown) · 3 Main unit · 4
EZS (German abbreviation for electronic ignition switch, EIS) · 5 Parktronic
control unit, ground connection, warning buzzer · 6 Fuse box (steady plus
Kl.30) · 7 Rear view camera (if installed) · 8 Rear Park Pilot sensors
Please be aware that this overview is only for illustration purposes. Always
lay the cable set in the most convenient and shortest way possible. For a
detailed description of the cable routing, please refer to the relevant
sections of the following manual.
Kufatec GmbH & Co. KG – Dahlienstr. 15 – 23795 Bad Segeberg – e-mail: info@kufatec.de
9
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>