KUFATEC E-Klasse W213 Complete Set Active Parking Assistant Parktronic Installation Guide
- June 16, 2024
- KUFATEC
Table of Contents
KUFATEC E-Klasse W213 Complete Set Active Parking Assistant Parktronic
Product Information
Specifications
- Product Name: Complete Set Active Parking Assistant Parktronic
- Version: v1.0 (01.02.2023)
- Manufacturer: Kufatec GmbH & Co. KG
- Address: Dahlienstr. 15, 23795 Bad Segeberg
- Email: info@kufatec.de
General Notes
Please read the following instructions carefully before installing the
Complete Set Active Parking Assistant Parktronic.
Safety Instructions
Ensure to follow these safety instructions during installation:
- Disconnect the vehicle’s battery before starting the installation process.
- Wear protective gloves and goggles while handling the components.
- Do not install the product in wet or damp conditions.
- Avoid direct contact with electrical components.
Requirements for the Intended Use
In order to use the Complete Set Active Parking Assistant Parktronic, the
following requirements must be met:
- Compatible vehicle model and year (refer to the product manual).
- Basic understanding of vehicle wiring and assembly.
- Standard toolset for automotive installation.
Product Usage Instructions
Assembly Instructions
To assemble the Complete Set Active Parking Assistant Parktronic, follow
these steps:
- Refer to Figure 3: Vehicle Overview for cable routing and component positions.
- Lay the cable set in the most convenient and shortest way possible.
- Refer to the relevant sections of the manual for detailed cable routing instructions.
Disassembly Instructions
To disassemble specific parts of the vehicle, follow these steps:
- Disassembly front bumper:
- Follow the instructions provided in section 10 of the manual.
- Disassembly covering engine compartment:
- Follow the instructions provided in section 11 of the manual.
- Disassembly sill trim front driver’s side:
- Follow the instructions provided in section 12 of the manual.
- Disassembly center console:
- Follow the instructions provided in section 13 of the manual.
- Disassembly main unit:
- Follow the instructions provided in section 14 of the manual.
- Disassembly back seat:
- Follow the instructions provided in section 15 of the manual.
- Disassembly covering rear driver’s side:
- Follow the instructions provided in section 16 of the manual.
- Disassembly rear bumper:
- Follow the instructions provided in section 18 of the manual.
Assembly Instructions
To assemble specific parts of the vehicle, follow these steps:
- Assembly rear sensors:
- Refer to section 19 of the manual for detailed instructions.
- Assembly front sensors:
- Refer to section 20 of the manual for detailed instructions.
- Assembly sensor holders with adhesive pads:
- Refer to section 21 of the manual for detailed instructions.
- Assembly/Connection control unit:
- Refer to section 22 of the manual for detailed instructions
- Cable routing to the rear:
- Refer to section 23 of the manual for detailed instructions.
- Cable routing to the front:
- Refer to section 24 of the manual for detailed instructions.
- Connection main unit:
- Refer to section 25 of the manual for detailed instructions.
- Connection EZS/EIS control unit:
- Refer to section 26 of the manual for detailed instructions.
- Assembly/Connection warning buzzer:
- Refer to section 27 of the manual for detailed instructions.
- Connection ground:
- Refer to section 28 of the manual for detailed instructions.
- Connection bridge Parktronic control unit:
- Refer to section 29 of the manual for detailed instructions.
- Connection fuse box:
- Refer to section 30 of the manual for detailed instructions.
- Note exchange rear view camera (if a rear view camera is installed):
- Refer to section 31 of the manual for detailed instructions.
- Cable routing rear view camera:
- Refer to section 33 of the manual for detailed instructions.
- Exchange rear view camera:
- Refer to section 34 of the manual for detailed instructions.
- Assembling the vehicle:
- Refer to section 35 of the manual for detailed instructions.
Coding and Additional Functions
To code and access additional functions, follow these steps:
- Coding interface:
- Refer to section 37 of the manual for detailed instructions.
- Additional vehicle function:
- Refer to section 38 of the manual for detailed instructions.
FAQ (Frequently Asked Questions)
- Q: What should I do if I encounter any issues during the installation process?
A: If you face any difficulties or have questions during installation, please contact Kufatec GmbH & Co. KG at info@kufatec.de for assistance.
Assembly Instructions
The following illustration shows the cable routing as well as the position of the individual components.
Figure 3: Vehicle overview
- Front Park Pilot sensors
- Park Assist sensors (brown)
- Main unit
- EZS (German abbreviation for electronic ignition switch, EIS)
- Parktronic control unit, ground connection, warning buzzer
- Fuse box (steady plus K1.30)
- Rear view camera (if installed)
- Rear Park Pilot sensors
Please be aware that this overview is only for illustration purposes. Always lay the cable set in the most convenient and shortest way possible.
- For a detailed description of the cable routing, please refer to the relevant sections of the following manual.
- Kufatec GmbH & Co. KG – Dahlienstr. 15 – 23795 Bad Segeberg –
- e-mail: info@kufatec.de
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>