PARAMITA R8 Bone Conduction Wireless Headphones Instruction Manual
- June 16, 2024
- PARAMITA
Table of Contents
R8
Bone Conduction Wireless Headphones
Manual
Instructions For Use
Thank you for purchasing the bone-conduction wireless Bluetooth headset produced by our company. In order to obtain a better listening experience, please wear and use the headset correctly, and please do not disassemble the hardware by yourself. Please read this manual carefully before using it. Thank you again for your support and like.
1.Specification parameters
| Bluetooth: | V5.3 |
|---|---|
| Communication range | ≥ 10m (without obstacles) |
| Waterproof grade | IPX7 |
| Frequency response | 20Hz-20KHz |
| Sensitivity | 85dB ± 3dB |
| Impedance | 8Ω |
| Support protocol | HFP/HSP/A2DP/AVRCP |
| Battery capacity | 230mAh |
| Horn | 16mm vibrating voice coil unit |
| Chip | AC7006F4 |
| Audio encoding | SBC/AAC |
| Listening time | 8H (80% volume) |
| Charging interface | Magnetic charging |
| Product size | 14510545mm |
| Product weight | about 29g |
| Packing list | earphones, silicone earplugs, charging cable, manual |
2. Product diagram
- Power on/off/volume up key
- volume down key
- LED indicator
- Magnetic charging port
- Multi-function keys: pause/play/ answer/hang up/next song/previous song/voice assistant
- call microphone
3. Wearing a diagram
Hang the earphones behind the neck, and the speakers on both sides are attached to the cheekbones to adjust the wearing comfort.
4. Function Overview
Steps:
Power on: Press and hold the power button for 3 seconds, and the indicator
light will flash red and blue. Pairing: Turn on the device “Bluetooth” and
click R8 to connect. When using the headset again, just turn it on and the
headset will automatically connect to the device.
5. Charging Operation
Connect the included magnetic charging cable to the headset and the USB port of the charging device for charging.
Note: Please use a 5V output adapter.
6. Key Definition
| Function | Operation Method |
|---|---|
| Start up | Long press the power button for 3s |
| Shutdown | Long press the power button for 3s |
| Stop/play | Click the multifunction button |
| Next song | Double-click the multi-function key |
| Previous song | Triple-click the multi-function key |
| Phone call | On call, click the multi-function key |
| Reject the call | On call, press and hold the multi-function button for 2s |
| Hang up the phone | On call, click the multi-function key |
| Wake up the voice assistant | Long press the multi-function button for 1s |
| Volume+ | Click the power (volume up) key |
| Volume- | Click the volume down button |
| Reset | Long press the power button for 8s |
7. Indicator light definition
Product status| State|
Led display
---|---|---
Use
| Start up| The blue light stays on for 2s
Shutdown
|
The red light stays on for 2s
Use|
Blue light flashes for 6s
Charging
| Charging| Steady red light
Full|
Steady blue light
FCC Requirement
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’ s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
*Our products strictly implement the national three-guarantee policy and support one-year free warranty from the date of purchase.
Any of the following situations will not enjoy a free warranty.
- Man-made damage.
- Exceeded the warranty period.
- Failure to provide valid proof of purchase.
- Damage caused by failure to operate and maintain according to the instructions.
- Unauthorized dismantling, repairing or soaking of product.
- Damage caused by other force majeure factors.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>