maytronics 99996339-SPL Premier Robotic Pool Cleaner User Guide
- June 16, 2024
- maytronics
Table of Contents
Quick start guide
99996339-SPL Premier Robotic Pool Cleaner
The Robotic Pool Cleaners by Maytronics deliver advanced cleaning
technologies, long lasting performance and easy maintenance. You and your
family will be free to enjoy swimming with full confidence that your pool is
completely clean.
The Robotic Pool Cleaners by Maytronics deliver advanced cleaning
technologies, long lasting performance and easy maintenance. You and your
family will be free to enjoy swimming with full confidence that your pool is
completely clean.
****Cautions & Warnings
- Use the originally supplied power supply only.
- Do not use an extension cable in any case whatsoever.
- Ensure the electrical outlet is protected by a ground fault interrupter (GFl) or an earth leakage interrupter.
- Keep the power supply out of standing water.
- Do not enter the pool while the Pool Cleaner is
- Use the originally supplied power supply only.
- Do not use an extension cable in any case whatsoever.
- Ensure the electrical outlet is protected by a ground fault interrupter (GFl) or an earth leakage interrupter.
- Keep the power supply out of standing water.
- Do not enter the pool while the Pool Cleaner is working.
- Unplug the power supply before servicing.
- Do not use the cable to take the pool cleaner out of the water. working.
- Unplug the power supply before servicing.
- Do not use the cable to take the pool cleaner out of the water.
- Use the Pool Cleaner in the following water conditions only: Chlorine Max 4 ppm; pH 7.0 – 7.8; Temperature 6 -34°C (43-93F); NaCl Maximum = 5000 ppm.
- Use the Pool Cleaner in the following water conditions only: Chlorine Max 4 ppm; pH 7.0 – 7.8; Temperature 6 -34°C (43-93F); NaCl Maximum = 5000 ppm.
Digital Power Supply
Digital Power Supply
Input: 100-250 AC Volts
50-60 Hertz
180 Watt
Output: <30 VDC
IP 54
Input: 100-250 AC Volts
50-60 Hertz
180 Watt
Output: <30 VDC
IP 54| Specifications:
Specifications:
Motor protection: IP 68
Minimum depth: 0.80m/2.6ft
Maximum depth: 5m/16.4ft
Motor protection: IP 68
Minimum depth: 0.80m/2.6ft
Maximum depth: 5m/16.4ft
---|---
Helpful hints
-
When working, the Power Supply should be placed in the shade.
-
When working, the Power Supply should be placed in the shade.
-
If the Dolphin is fitted with combined or wonder brushes, gently squeeze the brushes until they are soaked with water.
-
If the Dolphin is fitted with combined or wonder brushes, gently squeeze the brushes until they are soaked with water.
-
Release minimal required floating cable length to ensure proper pool coverage.
Leave excess cable rolled outside the pool. -
Release minimal required floating cable length to ensure proper pool coverage.
Leave excess cable rolled outside the pool. -
After each cleaning cycle wash the filters or cartridge. Clogged filters reduce scanning and cleaning efficiency.
-
After each cleaning cycle wash the filters or cartridge. Clogged filters reduce scanning and cleaning efficiency.
-
To remove the kinks stretch the cable out completely and let it sit for at least a day in the sun.
-
To remove the kinks stretch the cable out completely and let it sit for at least a day in the sun.
-
Store the pool cleaner in a shady place on its Caddy, if not on a caddy, place the pool cleaner upside down.
-
Store the pool cleaner in a shady place on its Caddy, if not on a caddy, place the pool cleaner upside down.
Robot operation
Set Up
Position the power supply at least 3.5m /12ft away from the edge of the pool.
Into the pool
Operation
The robot will now begin
working For a complete claning cycle At the end of the cycle, it will
automatically switch itself off.
out of the pool
Cleaning the filter
With the pool cleaner upside down open the bottom lid and pull it out.
Periodic maintenance
Unplug the power supply before servicing
Dismantle the impeller cover and clean around the impeller housing, then
reassemble.
Place the impeller cover at an angle so that the notch is on the second ring
of the spring.
Storage
8. Coil the cable and store in a cool, dry place. Do NOT store the robot and its accessories where it will be exposed to direct sunlight, excessive heat or frost.
Digital power supply
Full filter bag indicator
The power supply is equipped with a unique filter bag status indicator.
The red LED indicates 2 filter conditions:
- When blinking – The filter is partially blocked
- When lighted – The filter is blocked and must be emptied and cleaned If the LED does not shut-off after the filter has been emptied and cleaned, press the RESET button while the robot is working.
Weekly Timer
When the power supply is switched on, the 3 LEDs will blink for 5 seconds.
At this time by pressing the SELECT button you may choose a pool cleaning
schedule for the coming week.
Note! – The robot will always begin to work upon set-up.
LED 1-The robot will automatically work every day for a full cycle = 7 times a
week.
LED 2- The robot will automatically work every other day for a full cycle = 3
times a week.
LED 3-The robot will automatically work every 3 days = 2 times a week.
If you do not press any of the buttons in the first 5 seconds after the power
supply has been switched on the robot will work for one cycle only.
While the robot is working in weekly timer mode the LED will blink constantly
between cycles.
At the end of the week the power supply automatically switches off. You must
reschedule the robot.
For online product warranty registration:
registration.maytronics.com
For a detailed manual (incluing videos)
99996339-SPL
manuals.maytronics.com/en/
http://manuals.maytronics.com/99996339-SPL
Documents / Resources
|
maytronics 99996339-SPL Premier Robotic Pool
Cleaner
[pdf] User Guide
99996339-SPL, 99996339-SPL Premier Robotic Pool Cleaner, Premier Robotic Pool
Cleaner, Robotic Pool Cleaner, Pool Cleaner, Cleaner
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>