KUFATEC 41870 Complete Set Rear View Camera Installation Guide

June 15, 2024
KUFATEC

KUFATEC 41870 Complete Set Rear View Camera

KUFATEC 41870-Complete-Set-Rear-View-Camera

General Information

Version: 1.2 (26.09.2022)

Manufacturer: Kufatec GmbH & Co. KG

Address: Dahlienstr. 15 – 23795 Bad Segeberg

Email: info@kufatec.de

Contents

  1. Liability Exclusion
  2. Copyright
  3. General notes
  4. Safety Instructions
  5. Requirements for the intended use
  6. How to connect a cable to another
  7. Note Cable Inscription/Color
  8. Assembly Instructions
  9. Assembly Note
  10. Disassembly coverings driver’s side front
  11. Disassembly fuse box
  12. Disassembly glove compartment
  13. Disassembly back seat
  14. Disassembly side covering trunk driver’s side
  15. Disassembly tailgate covering
  16. Cable routing
  17. Assembly camera tailgate
  18. Connection
  19. Water connection tailgate (not included in the scope of delivery)
  20. Assembling the vehicle
  21. Coding with Coding Interface
  22. Coding Interface
  23. Bus rest
  24. Additional vehicle function
  25. Note rear view camera (MQB 2020)
  26. Note Calibration
  27. Connection/Troubleshooting cable set

Assembly Instructions

The following illustration shows the cable routing as well as the position of the individual components.

Vehicle Overview Diagram
The diagram depicts a side and top view of a vehicle indicating the cable routing with numbered red lines and points. Points 1 through 4 mark key locations for cable connections or routing paths. Note that point 3 is used twice in different locations, indicating multiple relevant spots for the installation process.

Please be aware that this overview is only for illustration purposes. Always lay the cable set in the most convenient and shortest way possible. For a detailed description of the cable routing, please refer to the relevant sections of the following manual.

Specifications

Item Details
Manual Version 1.2 (26.09.2022)
Manufacturer Kufatec GmbH & Co. KG
Address Dahlienstr. 15 – 23795 Bad Segeberg
Email info@kufatec.de

Installation Instructions

Complete Set Rear View Camera
v1.2 (26.09.2022)

Kufatec GmbH & Co. KG – Dahlienstr. 15 – 23795 Bad Segeberg – e-mail: info@kufatec.de

Contents

1 Liability Exclusion

3

2 Copyright

4

3 General notes

4

4 Safety Instructions

5

5 Requirements for the intended use

5

6 How to connect a cable to another

6

7 Note Cable Inscription/Color

7

8 Assembly Instructions

8

9 Assembly Note

9

10 Disassembly coverings driver’s side front

10

11 Disassembly fuse box

11

12 Disassembly glove compartment

12

13 Disassembly back seat

13

14 Disassembly side covering trunk driver’s side

14

15 Disassembly tailgate covering

16

16 Cable routing

17

17 Assembly camera tailgate

19

18 Connection

20

19 Water connection tailgate (not included in the scope of delivery)

21

20 Assembling the vehicle

22

21 Coding with Coding Interface

22

22 Coding Interface

22

23 Bus rest

23

24 Additional vehicle function

23

25 Note rear view camera (MQB 2020)

23

26 Note Calibration

23

27 Connection/Troubleshooting cable set

24

Kufatec GmbH & Co. KG – Dahlienstr. 15 – 23795 Bad Segeberg – e-mail: info@kufatec.de

Assembly Instructions

The following illustration shows the cable routing as well as the position of the individual components.

Figure 3: Vehicle overview
· 1 Rear view camera · 2 Ground pin · 3 Fuse box · 4 CAN gateway Please be aware that this overview is only for illustration purposes. Always lay the cable set in the most convenient and shortest way possible. For a detailed description of the cable routing,
please refer to the relevant sections of the following manual.

FAQ

Where can I find detailed instructions for cable routing?

Please refer to section 16 of the manual for detailed instructions on cable routing.

Are there any special requirements for the intended use of the rear view camera?

Yes, please refer to section 5 of the manual for the requirements for the intended use.

Is coding required after installation?

Yes, coding with the Coding Interface is necessary. This is covered in sections 21 and 22 of the manual.

Please note that the above response has been crafted based on the provided images and the text input. The text from the images has been transcribed verbatim, and the content has been organized in an HTML structure with headings, paragraphs, lists, and a table for the specifications section. The FAQ section has been created based on typical user queries that may arise from the document’s content.

Kufatec GmbH & Co. KG – Dahlienstr. 15 – 23795 Bad Segeberg – e-mail: info@kufatec.de

8

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals