KUFATEC 57299801 Complete Set Active Sound Installation Guide
- June 15, 2024
- KUFATEC
Table of Contents
- KUFATEC 57299801 Complete Set Active Sound
- Product Information
- Liability Exclusion
- General notes
- Safety Instructions
- Requirements for the intended use
- How to connect a cable to another
- Note Cable Inscription/Color
- Assembly Instructions
- Disassembly covering trunk
- Connection active sound
- Routing button cable
- Important Information Sound Booster
- Configuration And Software
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
KUFATEC 57299801 Complete Set Active Sound
Product Information
Specifications
- Product: Complete set active sound
- Manufacturer: Kufatec GmbH & Co. KG
- Address: Dahlienstr. 15, 23795 Bad Segeberg
- Email: info@kufatec.de
Copyright
Our installation and operation instructions, installation plans, software and other written and/or pictured documentations are protected by copyright.
FAQ
- Q: What should I do if I encounter difficulties during installation or operation?
- A: If you experience any problems during the installation or operation of the Complete set active sound, contact Kufatec GmbH & Co. KG for support. They can be reached via phone, email, or by visiting their workshop in Bad Segeberg.
- Q: Are costs for third-party installations covered by Kufatec GmbH & Co. KG?
- A: Costs arising from third parties assigned with the installation of Kufatec products are not covered. Kufatec will only compensate the proven costs of assembly and disassembly if there is an issue with their product.
- Q: What is the reimbursement limit for assembly and disassembly costs?
- A: The reimbursement of costs is limited to 110 Euro gross. Kufatec reserves the right to verify the claim in their workshop in Bad Segeberg.
- Q: Are missing parts or replacements covered by Kufatec?
- A: Costs arising from purchasing missing parts or replacements for defective parts from other suppliers are covered by Kufatec up to the amount that the subsequent delivery would have caused (saved expenses).
Liability Exclusion
Dear Customer,
Our cable sets are developed according to the connection- and circuit diagrams of the corresponding car manufacturers. Before the serial production, the cable sets will be adjusted and tested on an original vehicle. Therefore, the integration into the vehicle electronics follows the guidelines provided by the car manufacturer. Our installation instructions correspond to what is common in the vehicle electric/electronic regarding the required pre- understanding and the accuracy of the description in text and picture. They have proven its worth in practice hundreds of times. If you should experience any difficulties while installing one of our products, we are available to provide support via phone or email. Additionally, we offer you to execute the installation in our workshop in Bad Segeberg.
Costs, arising from third parties assigned with the installation of our products, are not being covered by us. We will only compensate the proven costs of the assembly and the costs of the disassembly of the defective product, if it turns out that there is an issue with our product. We limit the reimbursement of costs up to 110 Euro gross and reserve the right to verify the claim in our workshop in Bad Segeberg. The costs for shipping will be refunded if the claim is justified. We made the experience, that every professional workshop that is equipped with the necessary diagnostic devices, the diagnostic software and the manufacturer’s circuit diagrams, is able to find any possible defects in one of our products in a short period of time. The assembly and disassembly including troubleshooting the issue should therefore only take up to 60 minutes.
We also made the experience, that many professional workshops are not able to cope with the manufacturer’s circuit diagrams and can’t read common wiring schemes, which results in the calculation of several hours for the simplest installations. You will understand the fact, that we can neither take the risk of finding a reliable workshop for you, nor can we finance the training of the employees of your trusted workshop. Costs, arising from purchasing missing parts or replacements for defective parts from other suppliers, are covered by us up to the amount that the subsequent delivery would have caused (saved expenses). According to the legal warranty law, there would be no reimbursement right, if there was no deadline for the subsequent fulfilling set or the deadline for a subsequent fulfilling hasn’t expired.
That being said, if you have any problems during the installation or operation of one of our products call us, write us an email, send us the product or come by our workshop in Bad Segeberg with your vehicle. We are certain, that we can find a solution for any kind of concern.
Kind regards,
- Your Kufatec GmbH & Co. KG Team
Copyright
- Our installation and operation instructions, installation plans, software and other written and/or pictured documentations are protected by copyright.
- The publication or distribution of these documentations is only permitted with a written approval of Kufatec GmbH & Co. KG.
General notes
While developing this product, your personal safety combined with the best operating service, modern de- sign and an up-to-date production technique was especially taken into account. Unfortunately, despite the utmost care injuries and/or damages might occur due to improper installation and/or use.
Therefore, please read the following instruction manual fully and thoroughly and keep it! All articles of our production line pass through a 100% check – for your safety and security. We reserve the right to carry out technical changes which serve the improvement at any time. Depending on each product and purpose, it might be necessary to check each country’s legal regulations before installing and starting it. In case of warranty claims, the product has to be sent back to the seller in the original packaging with the attached bill of purchase and detailed defect’s description. Please, pay attention to the manufacturers return requirements (RMA). The legal warranty directions are valid.
The warranty claim as well as the operating permission becomes invalid due to:
- unauthorized changes to the device or accessories which have not been approved or carried out by the manufacturer or its partners
- opening the casing of the device
- repairing the device on one’s own
- improper use/operation
- brute force to the device (drop, willful damage, accident etc.)
During the installation, please pay attention to all safety relevant and legal directions. The device should only be installed by trained personnel or similarly qualified people.
In case of installation problems or problems concerning the functionality of
the device, limit the time to approx. 0,5 hours for mechanical or 1,0 hours
for electrical troubleshooting.
To avoid unnecessary costs and time-loss, send in an immediate support-
request, via the Kufatec-contact- form
(http://www.kufatec.de/shop/de/infocenter/).
In case of, let us know the following:
- Car chassis number/vehicle identification number
- Five-digit part number of the device
- Exact description of the problem
- Steps you have taken to solve the problem
Safety Instructions
The installation should only be performed by trained personnel. Only perform installations while in a voltage-free state. For example, disconnect the battery. Please pay attention to the instructions provided by the manufacturer.
- Never use bolts or nuts form the car’s safety devices for installation. If bolts or nuts form the steering wheel, brakes or other safety devices are used for installation of the device, it may cause an accident.
- Use the device with a DC 12V negative ground car. This device cannot be used in large trucks which use a DC 24V battery. If it is used with a DC 24V battery, it may cause a fire or accident.
- Avoid installing the device in places that would restrict you from driving safe or where it could damage the car’s other fittings.
- This device should only be used in combination with the mentioned vehicles. Only connections de- scribed within this instructions guide are allowed or required to use for installation.
- For damages caused by faulty installation, unsuitable connections or inappropriate vehicles, Kufatec GmbH & Co. KG assumes no liability.
- We advise you that these devices process data from the MOST – protocol of the vehicle. As the supplier of this device we don’t know the overall system you are working with. If your device causes damage, due to other changes made to the vehicle, Kufatec GmbH & Co. KG assumes no liability.
- Kufatec GmbH & Co. KG supplier does not guarantee the use of the product for changes within a new vehicle series.
- If the car manufacturers don’t agree with the installation of our device by reason of warranty, Kufatec GmbH & Co. KG assumes no liability. Please, check conditions and warranty before you begin the installation.
- Kufatec GmbH & Co. KG reserves the right to change the device specifications without notice.
- Subject to errors and changes.
Requirements for the intended use
- Only use this device in its intended area.
- In case of unprofessional installation, improper use or modification, the permission for the operation and the warranty claim will expire.
How to connect a cable to another
Table 1: How to connect a cable to another
| No. | Work step | Note |
|---|---|---|
| 1 | Take the cable of the vehicle, to which you want to connect, (green marked |
here) and
strip the insulation at one point with a suitable tool (cable stripper/cutter knife).
|
2| Now take the cable of the cable set, which you want to connect, (yellow
marked
here) and strip the insulation at the end.
|
3| Twirl the wires of the stripped cable together.|
4| Place the end of the cable you want to connect under the stripped point of
the cable of the vehicle…|
5| … and wrap the cable you want to connect around the cable of the vehicle.|
6| Lastly, stick insulating tape around the connection point. Make sure that
the isolation is put onto the connection professionally to prevent corrosion.|
Note Cable Inscription/Color
- If the cable set consists of colored cables, connect the cables according to the color.
- If all cables of the cable set have the same color, connect the cables according to the cable inscription.
Assembly Instructions
The following illustration shows the cable routing as well as the position of the individual components.
- 1 Control unit for sound generator
- 2 Connection cable set
- 3 Button (optional)
Please be aware, that this overview is only for illustration purposes. Always lay the cable set in the most convenient and shortest way possible. For a detailed description of the cable routing, please refer to the relevant sections of the following manual.
Assembly Note
- Important note for the assembly
- The vehicle used for the assembly instruction was a Skoda Kodiaq NS7. We would like to point out, that the disassembly of the individual parts can vary depending on the type of vehicle.
- Please make sure to keep that in mind.
- Note for assembling the vehicle
- Before you start assembling the vehicle, the system must first be tested for proper function.
Disassembly covering trunk
Table 2: Instructions to disassemble the covering in the trunk
| No. | Work step | Note |
|---|---|---|
| 1 | Remove the marked trunk floor and the other floors, that are located | |
| underneath of it. | ||
| 2 | Remove the marked side part by pulling it out upwards. | |
| 3 | Remove the marked load sill guard by pulling it out upwards. | |
| 4 | Loosen and remove the bracket by loosening the marked screw. | 1x10er nut |
| 4.1 | Loosen and remove the bracket by loosening the two marked screws. | 2xVZ10 |
| 5 | Loosen and remove the upper C-column covering by using an assembly lever. | |
| 6 | In order to remove the coat hook, the covering has to be removed. There are | |
| two screws located behind it (short + long) that have to be loosened. | 2xT30 |
Table 3: Instructions to disassemble the covering in the trunk
| No. | Work step | Note |
|---|---|---|
| 1 | Loosen and remove the marked screws at the lateral covering. | 4xT25 |
| 2 | Loosen and remove the two screws, that are located behind the two lashing |
eyes.
Afterwards you can loosen the side covering on the driver’s side.
| 2xVZ8
!!| Note: Please note that the disassembly of the side panel on vehicles
with third row seats (7 seater) may differ.|
Connection active sound
Table 4: Instructions to connect the active sound
| No. | Work step | Notes |
|---|---|---|
| 1 | Unplug the plug connection of the manufacturer side sound generator. It’s |
located at the marked spot, directly at the rear end of the vehicle (driver’s
side).|
2| Plug the cable set in between. The two 8-pole plugs get connected to both
of the manufacturer side plugs. The 18-pole plug is connected to the blue
module. Attach the module correctly using factory materials.|
!!| Important note: The set is controlled via smartphone app. Optionally,
the existing button can be used to activate and deactivate the sound. But the
button is not necessary. If the button is not needed, the step Routing button
cable can be skipped.|
Routing button cable
Table 5: Instructions to route the button cable
| No. | Work step | Notes |
|---|---|---|
| !! | Note: Only execute this step, if you want the button cable to be attached | |
| inside driver’s footwell. | ||
| 1 | Lay the button behind the side covering to the front to the backseat. | |
| 2 | Lay the button cable under the previously detached sill trim to the | |
| driver’s footwell. | ||
| 3 | In the footwell, lay the cable to the desired button position. |
Important Information Sound Booster
- Please use suitable screws that can withstand high loads of impact to attach the sound generator. In order to avoid losening of the screws due to the vibration, please secure the screws with appropriate factory material e.g threadlock. Please additionally check the stability of the Sound Booster regularly and if necessary retighten the screws. In case of non-compliance we do not assume liability for possible damages.
- After a successful installation we recommend to cover the sound generator with a zinc spray. Make sure that you cover the opening of the sound generator so that the zinc spray can’t get inside the sound generator.
- As additional safety the delivered steel cable and the retaining clips have to be attached to the Sound Booster as well as at a suitable position to the car. This safety cable is an additional security should the tightening screws be released due to the vibration.
Configuration And Software
Configuration
If a Bluetooth enabled module is available, the app ,,Kufatec-Link“ is
required for the configuration.
The app is available to download for free for IOS as well as for Android.
- For IOS in the Apple Store:
- For Android in the Google Play Store:
Software
Table 6: Notes for the software
| No. | Work step | Note |
|---|---|---|
| 1 | If the system does not work after the installation, please check if the |
system was installed correctly by having a look on the following link:
https://www.sound-booster.com/en/debugging.html. Our Sound Booster Software
for PC / Mac should be used for the commissioning or further debugging:|
| Step 1: Download the appropriate software via the following link:
https://www.sound-booster.com.|
| Step 2: Turn the ignition of the vehicle on and only then connect the PC /
Mac with a USB-cable to our module. It is important to check beforehand if
plus and minus are connected correctly. If this is not the case, it could
result in a damage to the computer or to the control unit.|
| Step 3: Start the downloaded software and click on search first and then on
connect.|
| You will be automatically forwarded to the diagnosis site, on which you can
see the following things at a glance:|
| Software: Software version / creation date|
| Active profile: The actually activated profile is indicated here.|
| Vehicle: The automatically identified vehicle is indicated here.|
| System status: Here you can tell, if the connections are correct.|
Table 7: Notes for the software
| No. | Work step | Note |
|---|---|---|
| 1 | If no current vehicle is identified, you have to select the vehicle via the | |
| manual selection as follows: | ||
| 2 | Open the dropdown-menu, search for your vehicle and select it. | |
| 3 | Click on Save Car to permanently save the vehicle to the module. | |
| If you don’t find your vehicle in the list, it might be necessary that the |
software has to be adapted to your vehicle. In that case, please contact us via e-mail: info@kufatec.de or by phone: +49 (0) 4551 / 80 810 888. We will make an ap- pointment with you, where we will adapt the software to your vehicle per Team Viewer (remote maintenance).|
Table 8: Notes for the software
| No. | Work step | Note |
|---|---|---|
| 1 | You also need to check if the right ESM is selected in our software: | |
| Open the dropdown-menu, search for the correct ESM and select it. | ||
| 2 | Click on Save ESM to permanently save the ESM to the module. | |
| 3 | For example, if you ordered a complete set with a Audi control unit you |
need to
select the ESM 4G0 907 160 B (A6/A7. If you installed the Maserati control unit instead of the Audi control unit you need to select the ESM 670036582 (Maserati).
|
| If the system does not work after all please get in contact with us via
e-mail: info@kufatec.de or by phone: +49 (0) 4551 /
80 810 888. We will check the issue as soon as possible.|
Contact
Kufatec GmbH & Co. KG
- Dahlienstr. 15 – 23795 Bad Segeberg
- e-mail: info@kufatec.de
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>