Kick Ass Grills VIJ5301 Insulated Jacket for Outdoor Instruction Manual
- June 15, 2024
- Kick Ass Grills
Table of Contents
Kick Ass Grills VIJ5301 Insulated Jacket for Outdoor
Product Information
This product is an insulated jacket designed for outdoor products. It is compatible with the following models: VIJ5301, VIJ5361, VIJ5421, VIJ5541, VIJSB2, VIJPB, LIJ27, LIJ30, LIJ36, LIJ42, LIJ54, LIJSB2, and LIJPB.
Specifications
- Model: VIJ5301 / LIJ30
- Cutout Dimensions:
- A: 33 (83.8 cm)
- B: 5 (12.7 cm)
- C: 3 (7.6 cm)
- D: 3 (7.6 cm)
- E: 3 (7.6 cm)
- F: 11 5/8 (29.5 cm)
Product Usage Instructions
Installation
- Before building the frame, consider the total weight of the liner, grill, and finishing.
Liner Installation
- Position the liner into the frame, ensuring that no part of the combustible enclosure protrudes above the top surface or in front of the face surface of the liner.
- If necessary, shim the liner for proper fit.
Grill Installation
- Use the proper equipment to support the grill.
- Place the grill into the liner and engage it over the liner lip across the back and sides.
- The liner is designed to support the grill without additional fasteners.
- If desired, any gap remaining between the liner and the combustible enclosure may be filled with a non-combustible sealant or caulk.
Insulated Jacket Dimensions
Refer to the provided dimensions for the specific models:
- LIJ27:
- Top View: 3-1/4 (8.3 cm) x 26-1/4 (66.7 cm)
- Front View: 3-1/4 (8.3 cm) x 25 (63.5 cm)
- Side View: 26-3/8 (67.0 cm) x 11-5/8 (29.5 cm)
- VIJ5301 / LIJ30:
- Top View: 3-1/4 (8.3 cm) x 29-1/4 (74.3 cm)
- FrontView: 3-1/4 (8.3 cm) x 25 (63.5 cm)
- Side View: 26-3/8 (67.0 cm) x 11-5/8 (29.5 cm)
- VIJ5361 / LIJ36:
- Top View: 3-1/4 (8.3 cm) x 35-1/4 (89.5 cm)
- FrontView: 3-1/4 (8.3 cm) x 22-1/4 (56.5 cm)
- Side View: 23-5/8 (60.0 cm) x 11-5/8 (29.5 cm)
- VIJ5421 / LIJ42:
- Top View: 3-1/4 (8.3 cm) x 41-1/4 (104.8 cm)
- Front View: 3-1/4 (8.3 cm) x 25 (63.5 cm)
- Side View: 26-3/8 (67.0 cm) x 11-5/8 (29.5 cm)
- VIJ5541 / LIJ54:
- Top View: 3-1/4 (8.3 cm) x 53-1/4 (135.3 cm)
- Front View: 3-1/4 (8.3 cm) x 25 (63.5 cm)
- Side View: 26-3/8 (67.0 cm) x 11-5/8 (29.5 cm)
FAQ
Q: Can gas and electrical connections be accessed from the rear or bottom?
- A: Yes, there are four square holes provided in the frame for gas and electrical connections. You can make these holes based on your requirements.
Q: Where should the regulator be installed?
-
A: The regulator should be installed outside the insulated jacket. It can be positioned anywhere in the gas supply line between the grill and the shutoff valve. Gas tubing should never be installed within the insulated jacket.
-
IMPORTANT: Before you build the frame, you must take into consideration the total weight of the liner, grill, and any finishing materials.
-
Refer to the cutout dimension table for the proper framing dimensions for the insulation jacket. Determine the entry point for both the gas inlet and electrical connections. Make the 4” square holes for gas and electrical connections
(rear or bottom access) based on your requirements. -
Note: that the electrical connections are located on the left side and the gas connections are located on the right side.
-
A Carpenter’s “spirit level” should be used to ensure that the framing is level, both front to back and side to side.
-
Note: Never under any circumstance should you install the transformer or run a quick disconnect hose in between the grill and the inside of the insulating jacket.
Liner Installation
- Position the liner into the frame. No part of the combustible enclosure can protrude above the top surface or in front of the face surface of the liner. Shim the liner if necessary.
Grill Installation
- Use the proper equipment to support the grill. Place the grill into the liner and engage it over the liner lip across the back and sides. The liner is designed to support the grill without additional fasteners.
- If desired any gap remaining between the liner and the combustible enclosure may be filled with a non-combustible sealant or caulk.
Cutout Dimensions
| Model | A | B | C | D | E | F |
|---|---|---|---|---|---|---|
| LIJ27 | 33” |
(83.8 cm)
| 5”
(12.7 cm)
| 23 ¾“
(60.3 cm)
| 4 ½”
(11.4 cm)
| 3”
(7.6 cm)
| 11 5/8”
(29.5 cm)
VIJ5301 / LIJ30| 36”
(91.4 cm)
| 5”
(12.7 cm)
| 26 ½”
(67.3 cm)
| 4 ½”
(11.4 cm)
| 3”
(7.6 cm)
| 11 5/8”
(29.5 cm)
VIJ5361 / LIJ36| 42”
(106.7 cm)
| 5”
(12.7 cm)
| 23 ¾”
(60.3 cm)
| 4 ½”
(11.4 cm)
| 3”
(7.6 cm)
| 11 5/8”
(29.5 cm)
VIJ5421 / LIJ42| 48”
(121.9 cm)
| 5”
(12.7 cm)
| 26 ½”
(67.3 cm)
| 4 ½”
(11.4 cm)
| 3”
(7.6 cm)
| 11 5/8”
(29.5 cm)
VIJ5541 / LIJ54| 60”
(152.4 cm)
| 5”
(12.7 cm)
| 26 ½”
(67.3 cm)
| 4 ½”
(11.4 cm)
| 3”
(7.6 cm)
| 11 5/8”
(29.5 cm)
VIJSB2 / LIJSB2| 15 ½”
(39.4 cm)
| 3 ½”
(8.9 cm)
| 26 ½”
(67.3 cm)
| 4 ¾“
(12.1 cm)
| 3 1/8”
(8.0 cm)
| 11 5/8”
(29.5 cm)
VIJPB / LIJPB| 26 ¼”
(68.0 cm)
| 5 3/8”
(13.7 cm)
| 23 7/8”
(62.7 cm)
| 4 ¾“
(12.1 cm)
| 3 1/8”
(8.0 cm)
| 11 5/8”
(29.5 cm)
WARNING
- The regulator is to be installed outside the insulating jacket. It can be positioned anywhere in the gas supply line between the grill and the shutoff valve.
- Gas tubing should never be installed within the insulated jacket.
Insulated Jacket Dimensions
LIJ27
VIJ5301 / LIJ30
VIJ5361 / LIJ36
VIJ5421 / LIJ42
VIJ5541 / LIJ54
VIJSB2 / LIJSB2
VIJPB / LIJPB
- Viking Range, LLC
- 111 Front Street
- Greenwood, Mississippi 38930 USA
- 662-455-1200
- For product information, call 1-888-(845-4641) or visit our web site atvikingrange.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>