IKEA 303.831.44 KULINARISK Wall Mounted Kitchen Hood Instructions

June 15, 2024
Ikea

IKEA 303.831.44 KULINARISK Wall Mounted Kitchen Hood Instructions

IKEA-303-831-44-KULINARISK-Wall-Mounted-Kitchen-Hood-Instructions-
product

Product Information

Specifications

  • Product Name: KULINARISK
  • Model Number: 303.831.44
  • Energy Efficiency: A++
  • Air Flow Rate at Best Efficiency Point: 250m3/h
  • Electric Power Input at Best Efficiency Point: 72W
  • Nominal Power of the Lighting System: 0.49W
  • Average Illumination of the Lighting System: 350 lux
  • Sound Power Level at the Highest Setting: 59dBA

Product Usage Instructions

Control Panel
The control panel consists of four buttons:

  • Speed: Turns the motor on/off at speed one.

  • $ Speed: Turns the motor on at speed two / Activate charcoal filter alarm.
  • % Speed: Turns the motor on at speed three / Reset alarm grease filter saturation.
  • & Press briefly: Turns the lighting system on and off at maximum intensity. Press and hold to change the lighting intensity up or down.

Filter Alarm
When the filter alarm is activated, the following messages will appear:

  • The grease filter must be cleaned: A key flashes once per second.
  • Anti-odour filter must be cleaned: A key flashes twice per second.

Motor Speeds

  • Speed: Turns the motor on/off at speed one.

  • $ Speed: Turns the motor on at speed two.
  • % Speed: Turns the motor on at speed three.
  • & Speed: Turns the motor on at Booster speed for 6 minutes. After 6 minutes, it returns to the previously set speed.

Activating Filter Alarm
To activate the filter alarm, follow these steps:

  1. Press and hold the button for approximately 2 seconds with all loads turned off (Motor+Lights).
  2. For grease filter alarm: LED (B) will flash twice to confirm.
  3. For activated charcoal filter alarm: LED (A) will flash twice to confirm. This is only for recirculation mode.

Resetting Filter Alarm
To reset the filter alarm, follow these steps:

  1. Press and hold the button for approximately 2 seconds with all loads turned off (Motor+Lights).
  2. LED (A) will flash three times to confirm.

Turning Off Filter Alarm
To turn off the filter alarm, follow these steps:

  1. Press and hold the button again for at least 2 seconds with all loads turned off (Motor+Lights).
  2. The relevant LED will flash once to confirm.

Product Description

Upper chimney

Lower chimney
Hood body
LED Lighting
Grease filter
Control panel

Control panel



A

Speed

| Turns the motor on/off at speed one.
---|---
Attention: the product is with the filter alarm disabled.

Press and hold the button for approximately 2 seconds, with all the loads turned off (Motor+Lights), to turn the grease filter alarm on. LED

(B) flashes twice to confirm.

To turn the alarm off, press the button again and hold for at least 2 seconds. The relevant LED (B) flashes once.



B

Speed

| ****

Turns the motor on at speed two / Activate charcoal filter alarm.

Attention: the product is with the filter alarm disabled.

Press and hold the button for approximately 2 seconds, with all the loads turned off (Motor+Lights), to turn the Activated Charcoal Filter alarm on. LED (A) flashes twice to confirm.

To turn the alarm off, press the button again and hold for at least 2 seconds.The relevant LED flashes once (A). Only for recirculation mode.


C

Speed

| Turns the Motor on at speed three / Reset alarm grease filter saturation.
Press and hold the button for approximately 2 seconds, with all the loads turned off (Motor+Lights), to reset the grease filter saturation alarm or charcoal filter alarm. LED (A) flashes three times.


D

Speed

| Turns the motor on at Booster speed.

This speed is timed to run for 6 minutes. At the end of this time, the system returns automatically to the speed that was set before. If it is

activated with the motor turned off, it will switch to OFF at the end of the time. To deactivate it, press button D or press button A.

E

Light

| Press briefly: Turns the lighting system on and off at maximum intensity.

Press and hold to change the lighting intensity up or down.

Filters Alarm.
When the filter alarm is activated, the following messages will appear over time:

  • The grease filter must be cleaned: “A” key flashes once per second.
  • Anti-odour filter must be cleaned: “A” key flashes twice per second.

Energy efficiency

Product fiche information, according to 65/2014| Unit| Value
---|---|---
Supplier’s name| IKEA
Model identifier| KULINARISK 303.831.44
Annual Efficiency Consumption| kWh/a| 34,8
Energy Efficiency Class|  | A++
Fluid Dynamic Efficiency|  | 37,6
Fluid Dynamic Efficiency Class|  | A
Lighting Efficiency| lux/Watt| 58
Lighting Efficiency Class|  | A
Grease Filtering Efficiency| %| 85,1
Grease Filtering Efficiency Class|  | B
Air flow at minimum speed| m3/h| 250
Air flow at maximum speed| m3/h| 380
Air flow at boost speed| m3/h| 700
Airborne acoustical

A-weighted sound Power Emission at minimum speed

| dbA| 51
Airborne acoustical

A-weighted sound Power Emission at maximum speed

| dbA| 59
Airborne acoustical

A-weighted sound Power Emission at boost speed

| dbA| 72
Power Consumption in off mode| Watt| 0,49
Power Consumption in standby mode| Watt| N/A
Additional information according to 66/2014
Time increase factor|  | 0,6
Energy Efficiency Index|  | 36,6
Measured Air flow rate at best efficiency point| m3/h| 406,0
Measured air pressure at best efficiency point| Pa| 463
maximum air flow| m3/h| 700,0
Measured electric power input at best efficiency point| W| 139,0
Nominal power of the lighting system| W| 6,0
Average illumination of the lighting system on the cooking surface| lux| 350
Sound power level at the highest setting| dBA| 59

To download the full version visit www.ikea.com

© Inter IKEA Systems B.V. 2020 23199 AA-2282309-6

Frequently Asked Questions

How do I activate the filter alarm?

To activate the filter alarm, press and hold the corresponding button for approximately 2 seconds with all loads turned off Motor+Lights.

How do I reset the filter alarm?

To reset the filter alarm, press and hold the corresponding button for approximately 2 seconds with all loads turned off Motor+Lights.

How do I turn off the filter alarm?

To turn off the filter alarm, press and hold the corresponding button again for at least 2 seconds with all loads turned off Motor+Lights.

References

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Related Manuals