MOUNTAIN TOP FO10HB02 Evoe Roll Cover Owner’s Manual
- June 15, 2024
- MOUNTAIN TOP
Table of Contents
MOUNTAIN TOP FO10HB02 Evoe Roll Cover Owner's Manual
1 WARNINGS
- Temperatures can be very high under the cover when closed.
- We do not recommend washing the EVOe roll cover in a brushless carwash, as the coating may be damaged due to use of chemicals.
2 CONDITIONS OF USE
- The EVOe roll cover design is lightweight and not suitable for extreme usage.
- Designed to withstand rain water, some water ingress may occur.
- Dust can enter the compartment through various gaps.
- Due to profiles which relatively quick heats up and cools down according to weather conditions can cause condensation on the inside.
- The EVOe roll cover is not designed for loading although it can support normal snow loads.
Goods in the bed must be secured during transportation to prevent damage.
3 EVOe OPERATION
3.1 – Open / Close
To open or close the EVOe roll cover, press the button on the remote for 1 second.
3.2 – Stop
To stop the EVOe roll cover, press the button on the remote for 1 second during operation. Press again for 1 second to resume operation. The EVOe roll cover will move in the opposite direction.
3.3 – Sleep Mode
The EVOe roll cover will enter Sleep Mode after 48 hours of inactivity. Press the the button on the remote for 1 second to wake the roll cover.
3.4 – Turn lights on / off
Press and hold the button on the remote for 3 seconds to turn the lights on or off. The lights will remain on for 8 minutes. During normal operation, the lights will turn on when opening, and turn off when closing.
3.5 – Auto Calibration
To calibrate / reset the EVOe roll cover, and press and hold the button on the remote for 12 seconds. During calibration, the roll cover will open completely, then close. The lights will slowly fade on and off. Calibration should be done monthly.
3.6 – Emergency Release
A release handle is located on the right side of the rear profile. Pull the handle down to disengage the motor and belt drive. The EVOe roll cover can then be operated manually.
3.7 – Reconnect after Emergency Release
To reconnect the motor and belt drive after an emergency release,
press the rear profile firmly into the belt drive handles. 2 audible “CLICKS”
should come from both drive handles.
After reconnecting, ensure the drive handles are properly connected to the
belt drive on both sides. Ensure that the GREEN tab is in the middle of the
YELLOW clip.
4 EVOe SAFETY FEATURES
4.1 – Anti-Pinch
If the EVOe roll cover is obstructed during operation, it will stop moving and
retract approx. 10cm, and the lights will flash rapidly.
After clearing the obstruction, press the button on the remote to resume
operation. The EVOe roll cover will open or close fully, depending on the
direction it met the obstruction.
4.2 – Motor Overload
If the motor is overloaded, it will stop, and the lights will flash slowly.
After a 2 minute pause, the EVOe roll cover will resume normal operation.
Motor overload can be caused by incorrect installation, or dirt and debris.
See section XX for proper maintenance of the EVOe roll cover.
If the motor overloads frequently after proper maintenance, contact your local
dealer.
4.3 – Temperature Overload
If the EVOe roll cover is operated under high temperatures, it can cause a temperature overload, and the roll cover will stop. The lights will flash slowly , and after a minimum 3 minute pause, the EVOe roll cover will resume normal opveration.
5 MAINTENANCE
- Loosen screw and place to the side.
- Use the multi tool to remove the plastic covers on the side profiles.
- ONLY FOR DOUBLE CAB
Regularly, and following cleaning, apply a PTFE-free all-conditions wet lube product to the inside of the canister ends.
6 CHECK MEASUREMENTS MAINTENANCE
7 BELT ADJUSTMENT
- If operation of the roll cover is not improved after tightening the belt drive, or abnormal sounds persists, refer to section Check glide rails maintenance on page 21.
8 CHECK GLIDE RAILS MAINTENANCE
- If abnormal sounds occur during operation of the roll cover, inspect the glide rails for debris or damage. If the glide rails are damaged or worn, then replacement glide rails are needed.
9 REPLACE PARTS
10 SERVICE
- Maintenance requirements and frequency depend on the actual usage of the roll cover and the environments and elements that it is exposed to.
- Clean and lubricate the cover accordingly to ensure the best possible operation and function.
ACCESSORIES
- Mountain Top Cargo Carrier combined load capacity of 45 Kg.
- See more accessories and spareparts www.mountaintop.dk.
Customer Service +45 4810 2950 (08:00 – 16:00 CET)
Support info@mountaintop.dk
Website www.mountaintop.dk
Address Pedersholmparken 10, 3600 Frederikssund,
Denmarkhttps://www.mountaintop.dk/
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>