Baboni Pet Door for Wall Steel Frame Installation Guide

Installation Guide
Pet Door for Wall
Please read this entire guide before beginning

IMPORTANT SAFETY INFORMATION

Explanation of Attention Words and Symbols used in this guide
This s the safety alert symbol. It s used to alert you fo potential personal inury hazards. Obey allsafety messages that follow this symbol to avoid possible injury or death.
WARN’NG ‘WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION CAUTION used with the safety alert symbol, indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
NOTICE
NOTICE is used to address safe use praciices not related o personal injury.
WARN’NG

• When children are present in the home, itis important fo consider the pet door during child proofing activities.
• The pet door may be misused by a child resulfing in the child accessing potential hazords that may be on the ather side of the pet door. Purchasers/Homeowners with swimming pools should ensure that the pet door is monitored ot all times and that the swimming pool has adequate barriers to entry. If a new hazard is created inside or outside of your home, which may be accessed through the pet door,
• Power Tooks. Risk of severe injury; follow all safety insiructions for your power tools. Be sure fo always wear your safety goggles.

CAUTION

• The user, prior to installation, must become familiar with all building codes that may affect the installation of the pet door and determine, along with a licensed contractor, its suitability in @ given installation. This pet door is not afire door.
• It is important for the owner and contraclor to consider any fisks that may be present inside or outside of the pet door, and any risks that may be created by subsequent changes o your properly and how they may relate 1o the existence and use, including misuse of the pet door.

NOTICE

• Keep these instructions with important papers; be sure fo transfer these instructions to the new owner of the propery.
• Check for electrical /plumbing fixtures that could be in the wall where you wish to place the pet door.
• Make sure the support fits snug and that it s not 1oo long or too short,In either instance, damage fo the wall can occur.
• If placing screws info vinyl siding it may be necessary fo dril @ hole through the siding slightly larger thon the heads of the screws. This willallow the screws fo fighten flush with plywood and not buckle the vinyl siding

Components

Tools Needed

• Framing Square
• Jigsaw
• Drill
• So” (8 mm) & 2″ (13 mm) Drill Bits
• Phillips Screwdriver
• Tape Measure
• Tape
• Pencil
• Level
• Scissors
• Stud Finder

Key Definitions

Outer Frame Size: Overall pet door dimensions
Cut-out Size: Opening cutin homeowner’s wall for proper fi and pet door installation
Replacement Flap Size: Overallflap size when removed from pet door
Flap Opening Size: Usable flap space for pet fo enter and exit thiough the pet door
Interior Frame: Pei door frame on the inside of home
Exterior Frame: Pet door frame on the outside of home

Installing Your Pet Door For Wall

Step 1

Measure
1A. Locate the site for the Pet Door for Wall . Locate the siuds in the proposed area. locate the center between the two studs
Using a pencil, draw a 5 (12.7 cm) vertical line on center about 10″ o 12 (25.4 cm fo 30.5 cm) above the floor.
1B. Mark the shoulder height of your pet on the vertical line. Draw a horizontal line through your mark
NOTICE
‘Check for elecirical and plumbing fxtures fhaf could be n The viall where you wish 1o place the pet door.
Step 2

Tape
2A. Place the template against the wall. Align the lines on the template with the lines on the wall. Tape in place.
2B. Check that the template is square. The vertical lines of both sides need to be extended up.
2C. Carefully trace the template with a pencil. Remove the template from the wall. Take @ moment fo review the hole location to ensure that  the template is level and that this is the best possible location for the:pet door.

Step 3

Cut Interior Wall
3A. Drill out the four comers of the rectangular hole with a %4 (8 mm) dhll bit.
Useful Tip: Use both hands to hold drill steady and straight ot 90° angle.
3B. Corefully cut the hole out using a jigsaw or other appropri- ate cutting device. Cut on line.
Useful Tip: When cuiting use both hands fo hold the saw slow, steady and straight ot a 90° angle.

3C. Fit Check: Using the A side of the pet door, check the fit. Do not force fit i itis figh.
3D. I the hole is too small, simply remove the pet door and re-cul o file the hole slightly o enlarge. Do not cut more than 8″ (3.2 mm| from your previous cut. Once the pet door properly goes info the hole, adjust to ensure the unit is square.
Step  4

Cut Exterior
A. Remove the pet door from the wall. Fold up the Center locator.
4B. Slide the folded piece info the back of A side as shown,
4C. Place A side of pet door back into wall and use the drywall screws 1o hold unit in place temporarly.

4D. Lifi he flap and push the Center Locator unfil it is touching the outside wall Make sure all the folded flaps are resting flush on the inside of tunnel and that you have not completely pushed Center Locator out of pet door. Mark
the holes on the Center Locafor.

4E. Remove the pet door from the inside wall. Drill out the marked holes (8mm) dill bit. Be careful to keep these holes s siaight with your as possible.

4F. You are now ready fo work from the outside wall Line up the fhree holes on the template with the three holes that you just driled. Check for square and fope in positon,
4G. Drill out the four corers of the rectangular hole with a 516″ (8 mm) dhrll bi.
Useful Tip: Use both hands 1o hold dril sieady and staight ot 0 90° angle.

4H. Carefully cut the hole out using a jigsaw or other appropriate cutting device. Cut on line.
Useful Tip: When cuiiing use both hands fo hold the sow slow, steady and siraight af @ 90° angle.
Useful Tip :if you are going though vinyl siding it is best 1o carefully score and cut the siding before cutting thiough plywood

4I . Fit Check: Using the B side of the pet door, check the fi. Do notforce fit i fight. I he hole is too small, simply remove the pet door and re-cut or fle the hole slighily fo enlarge. Do not cut more than %” (3.2 mm] from your previous cut. Once the pet door properly goes inlo the hole, adjust o ensure the unit is square,

Step 5

Install and Attach Interior

Optional Support Installation:

5A. Measure from the inside of outer wall fo the inside of inner wall s shown. Cut a 2X4 to the measured length, making sure that the cut is square. Remove any debris that may be inside the wall where the support wil be located.
Place support inside wall so that the top of support is flush with the botiom of cut-outs. Use 2 drywall screws (supplied) or 2 wood screws [optionall to fasten the inner side of support as shown.
Check again to make sure that the support is flush with bottom of cut-outs

NOTICE
There must be a position 1.18″ (30mm) on both sides.
Using the holes left by the drywall screws on the A side of pet door as pilot holes, drill a %4″ (13 mm) hole for the toggle bolts.

NOTICE I
ort00 short In efther instance, domage to the wall can occur.
5C. [T Use the 2 drywall screws (supplied) or 2 wood screws {optional) o fasten the outer poriion of the support
If placing screws info vinyl siding It may be necessary
NOTICE
o dril a hole through the siding sightly larger than the heads of the screws. This will allow the screws fo ighten flush with plywood and not buckle the vinyl siding

5d.NOTICE
F There must be a position 1.18″ (30mm) on both sides.
Using the holes left by the drywall screws on the A side of pet door as pilot holes, drill a %4″ (13 mm) hole for the toggle bolts.

5E. Install the toggle bolts and screw caps into the A side of the Pet Door as shown.
5F. Place the A side of the pet door back info the cut hole and fighten the bolis. Be careful not to overlighten. Snap screw caps into place.
Useful Tip: You moy need to start the toggle bolt into the hole. Be careful not 1o overtighten. Sometimes you need o hold the screw out so the foggle is locked while you tighten the screw unii the foggle is fight enough that it wilhold itself in place while you fiish tightening.
Step  6

Install and Attach Exterior

6A. You are now ready fo work from the outside wall. With B side in position, mark location of 4 foggle bolt holes. Remove B side of the pet door.
6B. Drill marked locations with 2″ (13 mm) dill bit.
6C. Install the toggle bolis and screw caps info the B side. Slide the B side of the Pet Door into the A side that is already installed on the inside. The unit will slide together just like it was in the package.
Fit Check: Inspect the unit for a snug it and any gaps that could cause o draftor waler penetration. Either fighten the fit or use closed cell foam and/ or silicone caulk n these areas.
Useful Tip: finsialling in @ vinyl siding application, you may want fo place closed cel foam and /or siicane caulk between the pef door flange and the siding,

Step 7

Train Your Pet
7A. Bring your pet fo the pet door. Temporarily tape both flaps up and try fo falk your pet into going through.
If your pet will not go hrough the door do ot force him thiough the door, simply wait for your pet to go through on his own.
Useful Tip: Somefimes i helps for you to be on one side of the door and your pe on the other. You moy fry persuading your pe through the door using o small piece of food or a freat.
You May Need
Use the Pet Door Installaion and Weather Proofing Kit helps fo insulate and weatherproof the pet door.
This kit not inside the package, you need fo buy it separately.
Search Pet Door Installation and Weather Proofing Kif on Amazon then you can find it

Replacement Flaps

Terms of Use and Limitation of Liability

No Unlawful or Prohibited Use
This Productis designed for use with pets only. This pe frining device s not infended to harm, injure, or provoke
Using this Product in @ woy th is not infended could result in violation of Federal, Stote or local laws.
Customer Care International
babonibusiness@outlook.com
Warranty
One Year Non-Transferrable Limited Warranty
Replacement Parts

Documents / Resources

| Baboni Pet Door for Wall Steel Frame [pdf] Installation Guide
Pet Door for Wall Steel Frame, Pet, Door for Wall Steel Frame, Wall Steel Frame, Steel Frame, Frame
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>