JOZERMADE Evaporative Air Cooler, 3-IN-1 Portable Air Conditioners and Windowless Room Cooler Humidification Instruction Manual
- June 15, 2024
- JOZERMADE
Table of Contents
Evaporative Air Cooler
with Remote Control
BRADN:JOZERMADE 
INSTRUCTION
MANUAL
Please read this instruction manual before using this innovative Air Cooler and keep it safe for future reference.
SAFETY INSTRUCTIONS
-
Carefully read the instructions before operating the unit
-
This appliance s for indoor use only.
-
This unit must only be connected to a 120V ~ 60 Hz outlet.
-
Installation must be in accordance with regulations of the country where the unit is used.
-
If you are in any doubt about the suitability of your electrical supply have it checked and, if necessary, modified by a qualified electrician.
-
This air cooler has been tested and is safe to use. However, as with any electrical appliance – use it with care.
-
Disconnect the appliance from the power socket before changing filters, dismantling, assembling or cleaning.
-
Avoid touching any moving parts within the appliance.
-
Never insert fingers, pencils or any other objects though the guard.
-
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities. It is also not intended for use by those with a lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety. Do not leave children unsupervised with this appliance.
-
Do not clean the unit by spraying it or immersing it in water.
-
Do not operate the appliance with wet hands.
-
Never connect the unit to an electrical outlet using an extension cord. If an outlet is not available, one should be installed by a qualified electrician.
-
Never operate this appliance if the cord or plug is damaged. Ensure the power cord is not stretched or exposed to sharp objects/edges.
-
A damaged supply cord should be replaced by the manufacturer or a qualified electrician in order to avoid a hazard.
-
Any service other than regular cleaning o filter replacement should be performed by an authorized service representative. Failure to comply could result in a voided warranty.
-
Do not use the appliance for any purpose other than its intended use.
-
Never use the mains plug as a switch to start and stop the air cooler. Use the provided ON/OFF button located on the control panel.
-
Always place the unit on a dry and stable surface. Do not move or tilt the unit when the water tanks are full.
-
The appliance should not be installed in laundry or wet rooms.
-
Do not use this unit in environments with flammable or explosive gases.
-
Avoid keeping the unit in direct sunlight for a long period of time.
-
Do not cover or restrict the airflow from the outlet or inlet grills.
-
For maximum performance the distance between the unit and a wall or objects should be at least 50cm.
-
While in operation, ensure that the level of the water tank does not exceed MAX and does not fall below MIN.
-
Keep the filters clean. Under normal conditions, filters should only need cleaning once every three weeks(approximately). Since the filters remove airborne particles, more frequent cleaning may be necessary, depending on the air quality.
-
In order to achieve maximun efficiency the unit should be placed near an open door or window.
Evaporative Air Coolers work with an evaporative cooling mechanism which requires cross ventilation. -
This unit will lose efficiency if the relative humidity within the room exceeds 60%.
-
The ambient operating temperature range s from 5°C to 40°C.
If used in low temperatures (as a humidifier) it is recommended to fill the water tank with warm (but not hot) water.
FEATURES
- 3in 1 Air Cooler
- Air Cooler, Humidifier and Air Cleaner with ionizer for improved air quality.
- The evaporative air cooler is an economical solution saving energy with no need for venting.
- 3 fan speeds: Low, Medium and High.
- 3 wind modes: standard, natural and sleep
- 12 hours timer
- Automatic horizontal swing for improved air distribution and faster cooling
- Honeycomb filter for improved cooling performance and air cleaning.
- Touch sensor control panel and remote control.
- Top water inlet for filling water easily
- Casters for great mobility
SPECIFICATIONS:
- Voltage: 120V~60Hz
- Power: 8OW
- Air flow: up to 1326 m’/hr
- Water tank: 5.5 Liters
PARTS REFERENCE
Please Note: Both water tanks are part of the main unit,
and are not removable.
INSTALLATION
- Remove all packaging — while keeping the air cooler in a vertical position.
- Make sure that all parts are present and that the unit is assembled correctly – including the castor wheels, which should be pushed into the 4 holes placed on the bottom of the unit. Note: Casters with brake are for the front, while the casters without brake are for the back.
- Water tank: Fill water tank with water ensuring that water tank does not to go above the MAX level visible on the front of the unit.
- CAUTION: WHEN COOLING/HUMIDIFYING, THE WATER LEVEL MUST NOT BE LOWER THAN THE “MIN” WATER LEVEL. NO WATER USE IS PROHIBITED!
- If you want to increase the cooling effect, you can put ice or the charged ice packs into either water tank, but be sure that by adding ice or ice boxes the water level does not go over the MAX limit. Empty some water if necessary.
- Make sure that the cooling pad and air filter are properly inserted into the back of the unit.
- Connect the power plug to a working socket, and then press the power button.
ICE PACKS
The ice packs can absorb the heat in the water, which in turn can lower the
temperature of the water tank.
This can make the air flow cooler.
- Fill the ice boxes with water and put them in the refrigerator until they are completely frozen.
- Put the frozen ice box into the water tank.
OPERATION
ON/OFF ( ) button
After connecting the power cord the air cooler is in standby mode. Touch the
POWER button to switch on the unit. The display will indicate the ambient
temperature and will gradually change as the ambient temperature changes.
Touch the POWER button again to turn the air cooler off.
SPEED ( ) button
Press the SPEED button to cycle through the fan speeds. The currently selected
fan speed will be illuminated on the display: F1: Low Speed, F2: Medium Speed,
F3: High Speed. The set speed will flash several times and then the display
will return to indicate the ambient temperature and will gradually change as
the ambient temperature changes.
MODE ( ) button
Press MODE button to change between the three airflow styles
Standard wind: The fan will blow at maximum speed
Natural wind: The fan speed will fluctuate to imitate a natural wind.
Sleep wind: The fan speed will decrease by one level per half hour and then
continue to run at Low Speed.
MER ( ) button
Press TIMER button to activate timer, the time can be set from 1 to 12
hours. LED screen will display the corresponding set time. The air cooler will
stop automatically after the set time has expired.
coot ( ) button
Press the COOL button to turn on the humidifying function, which cools the
air.
CAUTION: WHEN COOLING/HUMIDIFYING, THE WATER LEVEL MUST NOT BE LOWER THAN
THE “MIN” ‘WATER LEVEL. NO WATER USE IS PROHIBITED!
Press the button again to turn it off.
When the COOL function is turned off the Air Cooler will operate as a fan, and
the water will not be used to cool the air.
SWING ( ) button
Press the SWING button to turn the oscillation function of the air outlet on
or off. The swing indicator will be illuminated when the function is
activated. The vertical direction of the airflow can be manually adjusted.
REMOTE CONTROL
- The remote control includes one CR2025 battery. Battery comes pre-installed
- The remote control functions are the same as the control panel on the circulator. Follow the same instructions above to operate the fan remotely.
- Note: The remote control must be pointed towards the receiver on the fan in order to work.
- Do not mix new and old batteries.
- Please take out the battery for long time no use.
CLEANING AND MAINTENANCE
ATTENTION: Please shut off the unit and unplug from the mains before cleaning or performing any maintenance.
CLEANING THE SURFACE
Clean the plastic housing with a duster or a soft wet cloth.
Do not use chemical solvents (such as benzene, alcohol or gasoline) as they
may cause irreversible damage. Make sure no water enters the control panel.
CLEANING THE WATER TANK
Unplug the power cord and remove the honeycomb filter bracket. With a cloth
(dipped in a mild detergent), wipe the water tank. Before using the unit, the
tank should be rinsed by filling the tank and allowing it to drain through the
drain port.
Draining the water reservoir and refilling with fresh water at least once a
week will help reduce any mineral deposits and keep the filters clean.
Do not run the unit in Humidify mode with stale water in the tank.
We recommend emptying the tank and refilling it with fresh water if water has
been standing in the tank for an extended period of time.
MAINTAINING AND CHANGING THE HONEYCOMB FILTER PADS
The appliance is supplied with Honeycomb cooling / filters pads. The cleaning
frequency for the Honeycomb filter depends on local air and water conditions.
In areas where the mineral content of water is high (hard water), mineral
deposits may build up on the honeycomb cooling filter and restrict air flow.
If mineral deposits remain on the Honeycomb pads, the filter should be removed
and washed under fresh water. For a deeper clean a mild detergent should be
used with a soft brush. Once cleaned the filter should be rinsed in clean
water before leaving to dry.
We recommend cleaning the honeycomb filter at least every two months,
depending on your needs.
For best results, allow the honeycomb filter to dry after each use by turning
off the COOL function and running the unit as a fan for 15 minutes before
turning the unit off.
END OF SEASON MAINTENANCE
- Empty the tank and clean it following the instructions above.
- Clean the Honeycomb pad
- Store the Icepack in the water tank
- Cover the unit and keep it in a dry place.