logiware IPC2101A IP Camera User Guide

logiware IPC2101A IP Camera

Foreword

General

This manual introduces the functions, installation and operations of the camera.

Safety Instructions

The following categorized signal words with defined meaning might appear in the manual.

avoided,

could result in slight or moderate injury.

Caution| Indicates a potential risk which, if not avoided, may result in

property damage, data loss, lower performance, or unpredictable result.

Note| Provides additional information as the emphasis and supplement

to the text.

Protect Privacy Notice

As the device user or data controller, you might collect personal data of others such as face, fingerprints, car plate number, Email address, phone number, GPS and so on. You need to be in compliance with the local privacy protection laws and regulations to protect the legitimate rights and interests of other people by implementing measures include but not limited to: providing clear and visible identification to inform data subject the existence of surveillance area and providing related contact.

About the Manual

• The manual is for reference only. If there is inconsistency between the manual and the actu product, the actual product shall prevail.

• We are not liable for any loss caused by the operations that do not comply with the manual.

• The manual would be updated according to the latest laws and regulations of related regions. For detailed information, see the QR code or our official website. If there is inconsistency between paper manual and the electronic version, the electronic version shall prevail.

• All the designs and software are subject to change without prior written notice. The product updates might cause some differences between the actual product and the manual. Please contact the customer service for the latest program and supplementary documentation.

• There still might be deviation in technical data, functions and operations description, or errors in print. If there is any doubt or dispute, please refer to our final explanation.

• Upgrade the reader software or try other mainstream reader software if the manual (in PDF format) cannot be opened.

• All trademarks, registered trademarks and the company names in the manual are the
  properties of their respective owners.

• Please visit our website, contact the supplier or customer service if there is any problem occurred when using the device.

• If there is any uncertainty or controversy, please refer to our final explanation.

Important Safeguards and Warnings

Electrical safety

• All installation and operation should conform to your local electrical safety codes.
• The power source shall conform to the Safety Extra Low Voltage (SELV) standard, and supply power with rated voltage which conforms to Limited power Source requirement according to IEC60950-1. Please note that the power supply requirement is subject to the device label.
• Make sure the power supply is correct before operating the device.
• A readily accessible disconnect device shall be incorporated in the building installation wiring.
• Prevent the power cable from being trampled or pressed, especially the plug, power socket and the junction extruded from the device.

Environment

• Do not aim the device at strong light to focus, such as lamp light and sun light; otherwise it might cause over brightness or light marks, which are not the device malfunction, and affect the longevity of Complementary Metal-Oxide Semiconductor (CMOS).
• Do not place the device in a damp or dusty environment, extremely hot or cold temperatures, or the locations with strong electromagnetic radiation or unstable lighting.
• Keep the device away from any liquid to avoid damage to the internal
• Keep the indoor device away from rain or damp to avoid fire or
• Keep sound ventilation to avoid heat
• Transport, use and store the device within the range of allowed humidity and
• Heavy stress, violent vibration or water splash are not allowed during transportation, storage and installation.
• Pack the device with standard factory packaging or the equivalent material when transporting the device.
• Install the device in the location where only the professional staff with relevant knowledge of safety guards and warnings can access. The accidental injury might happen to the non-professionals who enter the installation area when the device is operating normally.

Operation and Daily Maintenance

• Do not touch the heat dissipation component of the device to avoid scald.
• Carefully follow the instructions in the Guide when performing any disassembly operation about the device; otherwise, it might cause water leakage or poor image quality due to unprofessional disassembly. Please contact after-sale service for desiccant replacement if there is condensed fog found on the lens after unpacking or when the desiccant turns green.(Not all models are included with the desiccant).
• It is recommended to use the device together with lightning arrester to improve lightning protection effect.
• It is recommended connect the grounding hole to the ground to enhance the reliability of the device.
• Do not touch the image sensor directly (CMOS). Dust and dirt could be removed with air blower, or you can wipe the lens gently with soft cloth that moistened with alcohol.
• Device body can be cleaned with soft dry cloth, which can also be used to remove stubborn stains when moistened with mild detergent. To avoid possible damage on device body coating which could cause performance decrease, do not use volatile solvent such as alcohol, benzene, diluent and so on to clean the device body, nor can strong, abrasive detergent be used.
• Dome cover is an optical component, do not touch or wipe the cover with your hands directly during installation or operation. For removing dust, grease or fingerprints, wipe gently with moisten oil-free cotton with diethyl or moisten soft cloth. You can also air blower to remove dust.

Warning

• Please strengthen the protection of network, device data and personal information by adopting measures that include but not limited to using a strong passwords, modifying passwords regularly, upgrading firmware to the latest version, and isolating computer network. For some device with old firmware versions, the ONVIF password will not be modified automatically along with the modification of the system password, and you need to upgrade the firmware or manually update the ONVIF password.
• Use standard components or accessories provided by manufacturer and make sure the device is installed and maintained by professional engineers.
• The surface of the image sensor should not be exposed to laser beam radiation in an environment where a laser beam device is used.
• Do not provide two or more power supply sources for the device unless otherwise specified. A failure to follow this instruction might cause damage to the device.

Introduction

Cable

• Cable type might vary with different devices, and the actual product shall prevail.
• Please waterproof all the cable joints with insulating tape and waterproof tape to avoid short circuit and water damage.

Cable information

■         Provides power to the device with PoE.

PoE is available on select model.

instructed in the Guide.

Device abnormity or damage could occur if power is not supplied correctly.

Network Configuration

Device IP setting can be finished with the “LW-IPC-ConfigTool” or on the web interface. You’ll find the download on https://www.go1984.com/hardware /logiware-ip-camera.html

• Device initialization is available on select models, and it is required at first use and after the device is reset.
• Device initialization is available only when the IP addresses of the device (192.168.178.178 by default) and the PC stays in the same network segment.
• The default login credentials (Username/Password) are admin/admin1234. (Please change your Password while adding the Camera to go1984 or after your first login).
• Planning useable network segment properly to connect the device to the network.
• The following figures and interfaces are for reference only, and the actual product shall prevail.

Modifying Device IP Address

• Step 1 Double-click “LW-IPC-ConfigTool.exe” to open the tool.
• Step 2 Click

The Modify IP interface is displayed.

• Step 3 Click Search setting.
  The Setting interface is displayed.

• Step 4 Enter the start IP and end IP of the network segment in which you want to search devices, and then click OK.

You can modify IP address of one or multiple devices in one time. This section is based on modifying IP addresses in batch.
Modifying IP addresses in batch is available only when the corresponding devices have the same login password.

• Step 1 Follow Step 1 to Step 4 in 2.1 to search devices in your network segment. After clicking Search setting, please make sure the username and password are the same as what you set during initialization, otherwise there will be “wrong password” notice.

• Step 2 Select the devices which IP addresses need to be modified, and then click Modify IP.
  The Modify IP Address interface is displayed.

• Step 3 Select Static mode and enter start IP, subnet mask and gateway.

  • IP addresses of multiple devices will be set to the same if you select Same IP.
  • If DHCP server is available in the network, devices will automatically obtain IP addresses from DHCP server when you select DHCP.

• Step 4 Click OK.

Logging in Web Interface

• Step 1 Open your favorite browser, enter the IP address of the device in the address bar and press Enter.
• Step 2 Enter user name and password in the login box, and then click Login.

Installation

Packing List

• The tools required for the installation including electric drill is not provided in the packing.
• The operatio n manual and related tool are contained on the QR code, and the actual packing shall prevail.

Dimension

Following figures are for reference only, the actual product shall prevail.

Installing Device

Installation method

Installing SD Card (Optional)

SD card slot is available on select models.
Disconnect the power from the device before installing the SD card.

Pressing reset button:

• Press the reset button for 10 seconds to reset the device.

Attaching Device

Note:Make sure the mounting surface is strong enough to hold at least three times of the device weight.

Cable going through the mounting surface

Cable going through the side cable tray

Installing Waterproof Connector

This part is only needed when there is waterproof connector come with the device and the device is used outdoor.

Adjusting Angle

• A vertical rotation ring is available on select models, which fails to support image rotation. Please refer to the real model for more details.
• IR light layout is different according to different models; please refer to the real model for more details.
• Please be aware of the image rotation direction when it turns to 64°vertically, which is to avoid IR light being blocked by the enclosure and causing worse IR effect.

References

• logiware IP Camera: Videomanagement Software für IP-Kameras - iOS/Android Clients
• Videoüberwachung und Aufzeichnung - go1984: Videomanagement Software für IP-Kameras - iOS/Android Clients

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>