Hanvon Q8W 2.4G Remote Control Bird Toy User Manual
- June 15, 2024
- Hanvon
Table of Contents
User Manual
Product overview
-
Power key
Press and hold for 3 seconds to turn on/off
Press and hold for 8 seconds to reset
Short press 3 times pairing -
Indicator light
Red indicator status display
a. Flashing: Low battery capacity < 20%, indicating that charging is required
b. Always on: Battery is charging
c. Off: Automatic shutdown when the battery is fully charged or low
Green indicator status display
a. Flash: Wireless connection waiting for pairing
b. Slow flash: Wireless connection waiting for connection
c. Always on:Successful Bluetooth connection successful -
USB-C Port
-
Pen box, open upward to store/take out the pen
-
Work area (drawing/writing)
-
A stylus accommodated in the pen box
Accessories
Stylus Nibs*5Pencil refillsUSB-A to C CableWarranty Card Quick GuideDigital Drawing Film
Bluetooth connection mode
3.1 Paired connection
3.1.1 Turn on the Bluetooth function of computer/mobile phone/tablet device.
3.1.2 Press and hold the power button for 3 seconds to turn on the machine and
Bluetooth is in the state of waiting pairing (the indicator light flashes
green).
3.1.3 Enter the interface of computer/mobile phone/tablet device Bluetooth
connection , search the device name “Q8 W” and complete the pairing.
3.1.4 Run the driver, set the parameters and test the product performance (no
driver is required for mobile phone/tablet products).
3.2 Reset and replace the paired equipment
3.2.1 Press and hold the power button for 8 seconds to reset.
Warm tips : Theoretically, drawing through Bluetooth connection is
supported on most mobile phones/tablets above Android 6.0. Still,a small
portion of mobile phones/tablets users may encounter the failure of drawing
with failed Bluetooth connectiondue to hardware performance mismatch. When
this happens , it is suggested customers switching towired connection mode.
Please contact customer service If you need any further assistance, .
Wired connection mode
4.1.1 Connect to computer/Android phone/Android tablet using a USB cable.
4.1.2 Run the driver, set the parameters and test the product performance (no
driver is required for mobile phone/tablet products).
Driver download
Login to the ugee official website (www.ugee.com.cn) to download the driver and complete the installation by following the guide steps (drivers are not required on mobile phone/tablet products ).
Replace the nibs
6.1 Pull out the refill by hand or other suitable tools.
6.2 Install the spare refill.
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Any changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to tryto correct the
interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction
IC Caution:
– English: This device contains licence-exempt transmitter(s)/receiver(s) that
comply with Innovation, Science and Economic Development Canada’s licence-
exempt RSS(s). Operation is subject to the following two conditions:
This device may not cause interference.
This device must accept any interference, including interference that may
cause undesired operation of the device.
The device has been evaluated portable device RF exposure requirements. The
device is kept at least 5 mm away from the user’s body.
Warm tips: A piece of Pencil refillsis included in the setIf you want to
draw on a piece of A5 paper onthe drawing board for writing and drawing.
Customers can replace the nib witha pencil refillsto experiencing paper-screen
synchronization on computer.
If you have any questions, please contact us in the following ways
Service hotline: 400-609-2889
WeChat repair: ugeechina
Website: www.ugee.com.cn
Technical Support QQ: 800184529 1
After-sales email: service@ugee.com.cn
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>