AIKE AK2630S High Speed Hand Dryer Instruction Manual

June 15, 2024
AIKE

High Speed Hand Dryer
AK2630S User Guide

Packing List

AIKE AK2630S High Speed Hand Dryer - Packing Cautions

Prohibited| Do not open the front panel.
Otherwise it may cause electric shock risk.
Do not let children hanging on the unit.
Otherwise the unit may be risk of falling.
Do not place other items on the machine.
Warning
Improper use may result in personal injury accidents.
---|---
Prohibited the use in bathroom  and showers| Do not use in places where water is directly splashed or in places where it is prone to freezing.
Otherwise It may cause electric shock and unit malfunction.
Do not spray water| Do not splash water.
Otherwise it may cause electric shock risk.
Prohibition of disassembling| Do not reform and perform unnecessary disassembling.
Otherwise it may cause fire, electric shock and injury accidents.
Please follow with instructions| Power must be turn off during maintenance.
Otherwise it may cause electric shock risk.
Please use rated voltage.
If the rated voltage exceeds ±10%, the unit will malfunction. It may cause fire,electric shock and unit malfunction if an incorrect power source is used.
Use fixed lines.
If used in combination with other appliances, it may cause abnormal heat in the shunt outlet and cause
fire.
If the unit is not working or have abnormal conditions, Please cut off the power supply and turn off the leakage circuit breaker to prevent accidents,then contact the supplier to check or maintenance.
Otherwise it may result in fire accidents due to electric shock, leakage, and short circuit.
Warning| Leakage circuit breaker must be installed.
Otherwise it may cause electric shock risk.
If the cord is damaged, it must be replaced by the manufacturer or professional to avoid risk.
It must operated by the professional construction person when install the unit.
Incorrect construction may cause electric shock and fire accidents.

Parameters

Model AK2630S Motor Power 550w
Rated Voltage AC220V Motor brush motor
Rated Input Power 1400w Sensing Distance 15-20cm
Air Speed 105m/s Waterproof IP24
Net Weight 3.0kg Anti-shock Category
Dimensions 250165238mm

Instructions

  1. When the hand is within about 15-20cm below the air outlet, the machine will automatically start the high-speed wind. When using, you can adjust the distance between your hands and the air outlet by yourself until your hands are dried. After the hand leave the air outlet for about 0.5 seconds, the machine stops working immediately.
  2. In order to avoid abnormal startup caused by the object passing through the induction area, the sensor needs to be activated after 0.2 seconds of induction.
  3. After the hand dryer runs continuously for more than 45 seconds, it will automatically stop working to avoid the continuous operation of the machine due to other objects attached to the sensor.

AIKE AK2630S High Speed Hand Dryer - Instructions

Routine Maintenance

  1. When servicing or repairing this machine, turn off the power or unplug it for safety;
  2. Wipe the surface of the hand dryer with a wrung soft cotton cloth or towel. Never rinse the hand dryer directly with water;
  3. Please use neutral detergent to clean the hand dryer. It is forbidden to use decontamination powder, abrasive powder and oil, acid and alkaline cleaners to clean the surface of the hand dryer;
  4. Do not put screwdrivers or any slender sharp objects into the air outlet, otherwise it may cause damage to internal parts and accidents such as electric shock;
  5. Please keep the surface of the transparent cover of the sensor free of scratches, and do not clean the surface with steel wool, sandpaper or any rough objects, otherwise it will reduce the sensitivity of the sensor;
  6. To ensure the safety of use, it is prohibited to use it for other purposes except to dry hands;
  7. To prevent damage to parts or personal injury, be sure to avoid direct contact of water with live parts, and do not hit the housing;
  8. For indoor installation and use only.

Filter Cleaning

Pinch the middle protruding part and pull down to remove the filter box. Remove the filter from the filter box. Gently dust or blow off the dust on the filter. If the filter screen is too dusty or used for more than 3 years, it needs to be replaced. It can be rinsed with water, and dried for use after cleaning.

Troubleshooting

Trouble Analyze Solutions
The hand dryer does not work Check the power switch Turn on the power
Induction device wire loose Connect the wires
Induction device failure Notify after-sales maintenance
The motor does not work The motor is damaged/There are other objects in the

wind wheel
No warm air| Damaged heating element
Whether the room temperature exceeds 25°C| When the ambient temperature exceeds 25°C, the heating will automatically turn off

Note: This product needs to be repaired by professionals of our company. Repairing the machine without any technical assistance may cause damage to parts or personal injury.

Product Introduction

AIKE AK2630S High Speed Hand Dryer - Introduction

Installation Diagram

AIKE AK2630S High Speed Hand Dryer - Diagram

  1. Please choose a flat wall for installation,and avoid installing in places where it is easy to touch people and doors;
  2. When installing, the air outlet should be more than 40 cm away from the countertop . If there is no countertop under the hand dryer, please refer to the installation height on the right;
  3. Do not have a mirror near the right side of the unit, as water droplets may splash when drying your hands. (more than 100 mm apart);
  4. Please use 1mm²~1.5mm² power cord.

Precautions Before Installation

Warning

  1. Before installation, please make sure that there are no obstacles within 40 cm below the sensor to ensure that the machine will not malfunction;
  2. Do not install the hand dryer on a wooden or plastic wall, otherwise there is a danger of the machine falling;
  3. Before installation, please make sure that the power supply used is in line with the specifications of the hand dryer;
  4. Do not perform installation construction while the product (power cord) is powered on;
  5. Wear gloves when installing, otherwise there is a risk of injury.

Please do not install in the following places (otherwise it may malfunction)

  1. Places with corrosive, oxidizing and reducing gases;
  2. Places prone to condensation;
  3. Places beyond 0~2000m above sea level;
  4. Places with direct sunlight and strong light;
  5. Places that can be directly exposed to water.

Installation Notes

AIKE AK2630S High Speed Hand Dryer - Installation Connection construction.
When installing the hand dryer without a junction box, you need to install a standard socket corresponding to the hand dryer on the upper right side of the hand dryer, with a distance of 20-50 cm. (If you need to connect the power cord directly, please insert a coverless junction box at the installation location. If the junction box is not used, the power cord will be squeezed out of the body and affect the installation.) Placing the Metal Mounting Plate.
Stick the mounting plate on the wall at a proper position, use a drill to drill holes in the designated positions, then insert the hollow wall anchors into the drilled holes, and pull out the power cord to connect with the power cord of the hand dryer.
When connecting the wires, the brown wire must be connected to the live wire, and the blue wire must be connected to the neutral wire, and wrapped with insulating tape to ensure no leakage. Install the machine.
Hang the machine on the mounting plate. Fix the machine and check the installation.

  1. Pull out the filter box, align the Phillips screwdriver at a 45-degree angle with the safety screw hole, and screw in a screw until the machine is firmly installed without shaking;
  2. Check if the power cord connector is connected;
  3. Check that the power cord switch is on.

Test Run

Step Check Result

Gently shake the
machine by hand| The machine is installed firmly without shaking| The installation of the machine is not firm, and vibration or abnormal noise will occur during work
Confirm the power supply voltage| Please use the rated voltage| Improper use of voltage will burn out the machine or cause personal accidents
Turn on the power| Close the external power switch or plug in the power plug| The power socket must match the machine plug
Turn the power switch to ON| Power indicator lights up| Please check the power supply when the indicator light is off
Dry your hands| High-speed wind blows out| If there is no wind, please confirm whether the hand is too far from the sensor
Turn the heating switch to ON| Hot air blows out| The machine can switch between hot and cold air when working

Importer: Zhejiang Aike Appliances Co.,Ltd.
Manufacturer: Zhejiang Aike Appliances Co.,Ltd.
Yong’an Industry Zone,Xianju,Taizhou City, 317306 Zhejiang,China
Official website:www.zjaike.com
E-Mail:support@zjaike.com AK-2630S-WGYYSMS-001

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals