Revillusion RBF24DLX 24 Inch Built In Firebox Owner’s Manual

Revillusion RBF24DLX 24 Inch Built In Firebox

Product Information

RevillusionTM Electric Fireplace

Specifications

• Model: RBF24DLX
• Model Number: 6909990100
• Model Variation: RBF24DLXWC
• Model Variation Number: 6909990200

Welcome

Thank you for purchasing the RevillusionTM Electric Fireplace by Dimplex. This user manual will provide you with important information on how to safely install and use your electric fireplace.

Product Usage Instructions:

Precautions:

When using the RevillusionTM Electric Fireplace, it is important to follow these basic precautions to ensure safety:

• Read all instructions before using the fireplace.
• Avoid covering or obstructing the front of the fireplace.
• The fireplace becomes hot during use, so do not touch hot surfaces with bare skin.
• Keep combustible materials at least 3 feet (0.9 m) away from the front of the fireplace.
• Exercise extreme caution when children or invalids are near the fireplace.
• Always turn off the fireplace when not in use.
• If the fireplace malfunctions has been dropped or is damaged, disconnect the power and have it inspected by an electrician before use.
• Do not use the fireplace outdoors.
• Avoid placing the fireplace where it may fall into the water.

Installation

Please follow the installation instructions provided in the separate installation manual included with your RevillusionTM Electric Fireplace. Failure to properly install the fireplace may result in electric shock or fire hazard.

Operation:

To operate the RevillusionTM Electric Fireplace:

1. Ensure the fireplace is properly installed and connected to a power source.
2. Turn on the fireplace using the power switch or remote control.
3. Adjust the flame intensity and heat settings according to your preference using the control panel or remote control.
4. Enjoy the realistic flame effect and warmth provided by the electric fireplace.

Maintenance:

To keep your RevillusionTM Electric Fireplace in optimal condition:

• Regularly clean the fireplace using a soft, dry cloth to remove dust and debris.
• Avoid using abrasive cleaners or solvents as they may damage the finish.
• Inspect the power cord for any signs of damage and replace if necessary.
• Refer to the maintenance section of the user manual for detailed instructions on cleaning and care.

FAQ

Q1: Can I use the RevillusionTM Electric Fireplace outdoors?

• A1 : No, this fireplace is designed for indoor use only and should not be used outdoors.

Q2: What should I do if the fireplace malfunctions?

• A2 : If the fireplace malfunctions, has been dropped, or damaged, disconnect power at the service panel and have it inspected by a reputable electrician before using it again.

Q3: How do I register my product for warranty?

• A3: You can register your RevillusionTM Electric Fireplace online at www.dimplex.com/register.
• Please make sure to have your model and serial numbers ready for registration.

Q4: Where can I find troubleshooting and technical support?

• A4 : For troubleshooting and technical support, you can visit www.dimplex.com/support or call our toll-free number 1-888-346-7539.
• Please have your model and serial numbers ready when seeking support.

We value your feedback!

• Your input helps to create even better products and experiences.
• Share the warmth and leave a review. dimplex.com/sharethewarmth

IMPORTANT SAFETY INFORMATION:

• Read this manual first before attempting to install or use the Revillusion™ Electric Fireplace. Always comply with the warnings and safety instructions contained in this manual to prevent personal injury or property damage.
• To view the full line of Dimplex products, visit www.dimplex.com

SAVE THESE INSTRUCTIONS

• Conventions used in this manual:
• NOTE: Procedures and techniques considered important enough to emphasize.
• CAUTION: Procedures and techniques which, if not carefully followed, will result in damage to the equipment.
• WARNING: Procedures, precautions and techniques which, if not carefully followed, will expose the user to the risk of fire, serious injury, or death.

Welcome

• Thank you for purchasing a Revillusion™ Electric Fireplace by Dimplex. Please use our convenient online registration page to record your model and serial numbers for future reference at:
• www.dimplex.com/register .
• CAUTION: Read all instructions and warnings carefully before starting installation. Failure to follow these instructions may result in a possible electric shock or fire hazard and will void the warranty.

IMPORTANT INSTRUCTIONS

Basic Precautions

• When using any electrical appliance, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons.

These precautions include:

1. Read all instructions before using the RevillusionTM Electric Fireplace. DANGER: High temperatures may be generated under certain abnormal conditions. Do not partially or fully cover or obstruct the front of the fireplace.
2. This fireplace is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. The trim around the heater outlet becomes hot during heater operation. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9 m) from the front of the fireplace.
3. Extreme caution is necessary when the fireplace is used by or near children or invalids and whenever the fireplace is left operating and unattended.
4. Always turn off the fireplace when it is not in use.
5. Do not operate the fireplace after it malfunctions, has been dropped, or damaged in any manner. Disconnect power at the service panel and have the fireplace inspected by a reputable electrician before using.
6. Do not use this fireplace outdoors.
7. Never locate the fireplace where it may fall into a bathtub or other water container.
8. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock, or fire, or damage the fireplace.
9. To prevent a possible fire, do not block air intakes or exhaust in any manner
10. To disconnect the heater, turn the controls to OFF and turn off the power to the heater circuit at the main disconnect panel.
11. All electrical heaters have hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or flammable liquids are used or stored.
12. Do not modify this fireplace. Use it only as described in this manual. Any other use may cause fire, electric shock, or injury to persons.
13. Do not burn wood or other materials in this fireplace.
14. Disconnect all power coming to the fireplace at the main service panel before performing any cleaning or maintenance.
15. When transporting or storing the fireplace, keep it in a dry place, free from excessive vibration, and store to avoid damage.

NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void user’s authority to operate the equipment.

Special Precautions

• WARNING: Remote control contains a small battery. Keep away from children. If swallowed, seek medical attention immediately.
• WARNING: Do not install battery backwards, charge, put in fire or mix with used or other battery types as it may explode or leak causing injury.
• WARNING: Do not open the unit. There is a risk of electric shock. There are no user-serviceable parts inside.
• CAUTION: Always use a qualified technician or service agency to repair the electric fireplace.

FCC Compliance

CAUTION: This unit has been tested and found to comply with the limits for Class B digital devices, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This unit generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception, which can be determined by turning the unit OFF and ON, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the unit and the receiver.
• Connect the unit to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This unit complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This unit may not cause harmful interference,
2. this unit must accept any interference received, including interference that may cause undesired operation.

FCC CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN NO USER-SERVICEABLE PARTS INSIDE

Specifications

• The Revillusion™ Electric Fireplace offers an alternative to a wood or gas fireplace.
• It can give your existing fireplace new life or transform a cabinet or media center of your own into a stunning focal point.

Electrical

Volts| 120 V

60 Hz

---|---
Amps| 11.25 A @ 25o C

12.50 A @ 0o C

Watts| 1350 W @ 25o C

1500 W @ 0o C

Wiring| Plug-in fireplace,

hardwire optionally

Bulb Type| LED
Approvals| ****

Dimensions

640 mm

| 24 ¼”

640 mm

Height| 22 ⅞”

581 mm

| 22 ⅞”

581 mm

Depth| 12 ⅛”

307 mm

| 12 ⅛”

307 mm

• Operation Temperature
  • -4o to 104o F (-20o to 40o C)
• WARNING: Electrical outlet wiring must comply with local building codes and other applicable regulations to reduce the risk of fire, electric shock, or injury to persons.
• NOTE: A 15 Amp circuit is required. A dedicated circuit is preferred, but not essential in all cases. A dedicated circuit will be required if, after installation, the circuit breaker trips or the fuse blows on a regular basis when the heater is operating. Additional appliances on the same circuit may exceed the current rating of the circuit breaker.

Unpacking the Unit

• The unit comes packed with a protective sheet covering the front of the unit. This sheet is intended to prevent dust and debris from entering during construction.
• This sheet is designed so that it can be partially removed to complete the wiring and unpacking and can be reinstalled until the final installation is complete.
• The log set was installed on the grate and the grate was permanently fixed to the fireplace at the factory.
• Carefully remove the packaging from around the log set. Make sure the wires from the log set are connected securely to the grating box.
• CAUTION: The Realogs® contain LEDs to create a unique pulse and glow effect. Handle the log set carefully. They are fragile and can crack or break if dropped.

Installation

Framing

1. The RevillusionTM Electric Fireplace/Fireplace Insert does not require any special venting.
2. To build the rough-in opening, follow the framing dimensions below.

NOTE: The materials used for the finished surround must be cut to precise dimensions (dimensions B & C) as the 1/4″ (0.6 cm) self-trimming flange is only to create a finished appearance.

Front Glass Installation Method

1. Before installing the front glass installation, remove the hole caps from the fireplace.
2. Make sure all hardware has been included in the package prior to starting.
3. Install hardware items A and B onto the front glass.
4. Install brackets onto the fireplace with screws C.
5. Place front glass into a fireplace and secure with screw D
6. Install top trip piece.

Placement

• This fireplace is a zero clearance design, with the exception of the top of the unit, where any insulation and vapor barrier should be placed a minimum of 2” (5.1 cm) from the fireplace.
• CAUTION: The front of the firebox must not be recessed as this will prevent adequate airflow out of the heater.
• DANGER!: High temperatures may be generated under certain abnormal conditions. Do not partially or fully cover or obstruct the front of the fireplace.
• WARNING: All electrical heaters have hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or flammable liquids are used or stored.
• WARNING: The electric fireplace must NOT be in direct contact with any building vapor barrier or insulation.
• NOTE: If the fireplace is going into an existing opening and used with the trim accessory, locate the fireplace as needed for the best appearance.

1. Place the fireplace into the opening. Level with shims if necessary.
2. From the inside of the unit, gently remove the interior brick panels (attached magnetically).
3. Screw the mounting flanges directly to the stud opening or bend the flange out to 90° to be flush with the surrounding studs and screwed to the studs using suitable hardware.

Bathroom Installation

• This electric fireplace must be protected by a GFI circuit when installed in an area where water is present. If the unit is installed using a receptacle, it must be readily accessible.
• This fireplace is not watertight and must be installed to prevent water from entering the unit. Install the unit away from showers, tubs, etc. Keep towels and other combustible materials 3 feet (0.9 m) away from the front of the unit.

Electrical

General

• The fireplace is packaged with a three-prong plug installed for plug-in convenience. Hardwiring the fireplace is also an option for installation.
• WARNING: Do not attempt to wire your own new outlets or circuits. To reduce the risk of fire, electric shock, or injury to persons, always use a licensed electrician.
• WARNING: Make sure the circuit on which the fireplace is to be installed has the power cut off at the service panel until installation is complete.

Power Cord

• WARNING: This fireplace is for use on a 120V circuit and has a grounding plug that looks like the plugin Figure 1. Make sure the plug is connected to an outlet having the same configuration as the plug. No adapter should be used with this product.
• WARNING: Do not use this fireplace with an extension cord. Plug the cord directly into an appropriate wall receptacle.

Removing the Power Cord for Hardwire Installation

To remove the power cord:

1. Locate the power cord on the back of the fireplace. Remove 2 screws and slide the electrical box back.
2. Unscrew the 2 wire connectors.
3. Cut the green (ground wire) leaving enough length to reuse the wire.
4. Replace assembly with the hardwire cover (included).

Permanent Heat Disable

The fireplace heater can be permanently disabled by removing the electronic jumper on the main control board. Disable the heater before any additional installation takes place.

To permanently disable the heater:

1. Locate and remove the panel on the top left of the unit.
2. Pull out the electronic jumper (shunt), on the on the left side of the screw in the right corner of the board. The label beside the jumper is “HT EN”.
3. Reinstall the previously removed panel.

NOTE: If heater button is pressed when heater is permanently disabled, H– will be displayed.

Hardwire Installation

1. Allow 8″ (20.3 cm) of service cable for connecting the power supply wires to the junction box on the unit when installing before finishing the wall. Allow up to 4 ft (122 cm) of service cable for connecting the power supply wires to the junction box when installing after finishing the wall.
2. Wire a dedicated, properly fused circuit with a 15 A rating.
3. Feed the service cable through the electrical cover on the back of the unit and secure using a 1/2″ (1.3 cm) approved strain relief connector.
4. Remove the outer jacket and strip the individual conductors 1/2″ (1.3 cm) from the end.
5. Follow the instructions pertaining to your specific installation.
6. Wiring inspection can be done from the front of the unit: remove the access panel, to the right of the controls, to access the service cable and wires from the unit.

Direct Power Wiring (120 V)

• All wiring must be completed prior to installing the electric fireplace.
• Use 2-conductor wires with ground (3 wires total) from the power supply (breaker panel) to the junction box on the electric fireplace.

To install 120 V direct power wiring:

• Pull out the red-N, black-L, and green-G wires.
• Connect N (white) and N (red) in the electric fireplace to the neutral wire from the power supply.
• Connect the L (black) wire from the electric fireplace to the live wire from the power supply.
• Connect the G (green) ground wire from the electric fireplace to the ground from the power supply.
• Insert all the wiring back into the electric fireplace and secure it with a cable clamp.
• Make sure all connections are tight.

Wall Switch (120 V)

• NOTE: Use a single pole, single throw (On/Off) wall switch that is rated for a minimum of 15 A.

Before installing the wall switch:

• Connect a 2-conductor wire with the ground (3 wires total) from the power supply panel to the main switch wall box.
• Connect a 2-conductor wire with the ground (3 wires total) from the main switch wall box to the junction box on the fireplace.

To install a 120 V wall switch:

1. Pull out the red, black, and green wires.
2. Connect the red-N wire from the fireplace to the neutral wire from the power supply panel.
3. Connect black-L from the fireplace to the line wire from the main power wall switch using a wire connector.
4. Connect the other end of L (black) to the L terminal of the main power wall switch.
5. Connect G (green) from the electric fireplace to the ground wire of the main power wall switch using a wire connector (not supplied).
6. Secure the two remaining ground wires (green) with a ground screw in the main switch wall box.
7. Insert all the wiring of the main power wall switch into the main switch wall box.
8. Insert all the wiring back into the electric fireplace and secure with a cable clamp.
9. Ensure all connections are tight.

Operation

General

• WARNING: The RevillusionTM Electric Fireplace must be installed properly before it is used.
• CAUTION: Except for installation and cleaning described in this manual, an authorized service representative should perform any other servicing.
• This fireplace operates with ComfortSaver™ technology, which automatically adjusts the fan speed and heater wattage to safely and precisely match the requirements of the room based on the thermostat setting.
• The heater operates such that once the room reaches the set point, the fan and heater will continuously run at a low level to maintain the desired room temperature. If the temperature in the room rise significantly (e.g., sun coming through a window or a central furnace turns on) the heater will turn off and periodically turn back on to circulate the air around the unit until the room temperature drops and requires the heater to be constantly on again.
• NOTE: The fireplace retains heat after shutdown. When the heat is turned OFF, there is a 2-minute cool down period before the fan shuts off completely.

Touch Panel and Remote Controls

• The touch panel controls for the RevillusionTM Electric Fireplace are located on the front panel. Touch an icon to activate. The selected setting displays on the left side of the panel.
• A multifunction remote control is included. The remote control has a range of approximately 30 ft (9 m). To operate correctly, the remote control must be pointed toward the front of the electric fireplace.

Maintenance

Resetting the Temperature Cutoff Switch

• Should the heater overheat, an automatic cut out will turn the heater off and it will not come back on without being reset.
• If the fireplace is installed with a plug, it can be reset by unplugging the fireplace, waiting 5 minutes and plugging back in.
• If the fireplace is hard-wired, it can be reset by turning of the electrical breaker, waiting 5 minutes and turning the breaker back on.
• CAUTION: If you need to con-tinuously reset the heater, unplug the unit and call technical support at 1-888-346-7539.

General Maintenance

• Inspect the electric fireplace regularly, depending upon conditions, and at a minimum yearly intervals. Remove the front glass and clean the logs, grate, and base as required.
• WARNING: Disconnect power and allow heater to cool before attempting any maintenance or cleaning to reduce the risk of fire, electric shock, or injury.
• CAUTION: Except for installation and cleaning described in this manual, an authorized service representative should perform any other servicing.

Clean Logs and Base

• The electric fireplace set should not be operated with an accumulation of dust or dirt on or in the fireplace, as this can cause a build-up of heat and eventual damage.
• Dust and vacuum the fireplace as needed. Use a damp cloth and a mild detergent to clean painted surfaces of the electric fireplace. Never use abrasive cleaners.

Clean Reflector Screen

• The reflector screen is cleaned in the factory during the assembly operation. During shipment, installation, handling, etc., the screen may collect dust particles; these can be removed by dusting lightly with a clean dry cloth.
• To remove fingerprints or other marks, clean the reflector screen damp cloth. Never use abrasive cleaners. Dry the screen completely with a lint-free cloth to prevent water spots.

Remote Battery Replacement

To replace the battery:

1. Remove the battery cover screw using a Philips screwdriver.
2. Slide the battery cover open.
3. Install a 3V (CR2032) lithium battery in the battery holder. The positive (+) side of the battery faces up.
4. Close the battery cover and secure the screw.

• The used battery must be recycled or disposed of properly. Check with your Local Authority or Retailer for recycling advice in your area.
• CAUTION: When transporting or storing the heater and cord, keep in a dry place, free from excessive vibration and store so as to avoid damage.

Warranty

Two-Year Limited Warranty

• Products to which this limited warranty applies
• This limited warranty applies to your newly purchased Dimplex RevillusionTM electric fireplace This limited warranty applies only to purchases made in any province of Canada except for Yukon Territory, Nunavut, or Northwest Territories or in any of the 50 States of the USA (and the District of Columbia) except for Hawaii and Alaska. This limited warranty applies to the original purchaser of the product only and is not transferable.

Products excluded from this limited warranty

• The fireplace is only covered for transportation to the end user and will not be covered if damage occurs during normal operation and/or maintenance. Products purchased in Yukon Territory, Nunavut, Northwest Territories, Hawaii, or
• Alaska is not covered by this limited warranty. Products purchased in these States, provinces, or territories are sold AS IS without warranty or condition of any kind (including, without limitation, any implied warranties or conditions of merchantability or fitness for a particular purpose) and the entire risk of as to the quality and performance of the products is with the purchaser, and in the event of a defect the purchaser assumes the entire cost of all necessary servicing or repair.

What does this limited warranty cover and for how long

• Products, other than fireplace surrounds (mantels) and trims, covered by this limited warranty have been tested and inspected prior to shipment. Subject to the provisions of this warranty, Glen Dimplex Americas warrants such products to be free from defects in material and workmanship for a period of 2 years from the date of the first purchase of such products as follows: (a) a repair or replacement warranty on defective products or parts, including in-home services, for the first year following the date of first purchase; and (b) thereafter, a replacement of parts warranty on defective products and parts (with no in-home services) for the 1 year period commencing on the first anniversary of first purchase and ending on the second anniversary of the date of first purchase.
• Dimplex fireplace surrounds (mantels) and trims covered by this limited warranty have been tested and inspected prior to shipment and, subject to the provisions of this warranty, Glen Dimplex Americas warrants such products to be free from defects in material and workmanship for a period of 1 year from the date of first purchase of such products. Warranty services do not include in-home services.
• The limited 2-year warranty period for products other than fireplace surrounds (mantels) and trims and the limited 1-year warranty period for fireplace surrounds (mantels) and trims also applies to any implied warranties that may exist under applicable law. Some jurisdictions do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to the purchaser.

What this limited warranty does not cover

• This limited warranty does not apply to products that have been repaired (except by Glen Dimplex Americas or its authorized service representatives) or otherwise altered. This limited warranty does further not apply to defects resulting from misuse, abuse, accident, neglect, incorrect installation, improper maintenance or handling, or operation with an incorrect power source.

What you must do to get service under this limited warranty

• Defects must be brought to the attention of Glen Dimplex Americas Technical Service by contacting Dimplex at 1-888-346-7539 or 1367 Industrial Road, Cambridge Ontario, Canada N3H 4W3. Please have proof of purchase, catalog/model, and serial numbers available when calling. Limited warranty service requires proof of purchase of the product.

What Glen Dimplex Americas will do in the event of a defect

• In the event a product or part covered by this limited warranty is proven to be defective in material or workmanship during (i) the 2 year limited warranty period for products other than fireplace surrounds (mantels) and trims, and (ii) the 1 year limited warranty period for surrounds (mantels) and trims, you have the following rights:
• Glen Dimplex Americas will in its sole discretion either repair or replace such defective product or part without charge. If Glen Dimplex Americas is unable to repair or replace such product or part, or if repair or replacement is not commercially practicable or cannot be timely made, Glen Dimplex Americas may, in lieu of repair or replacement, choose to refund the purchase price for such product or part.
• Limited warranty service will be performed solely by dealers or service agents of Glen Dimplex Americas authorized to provide lim-ited warranty services.
• For products (other than surrounds (mantels) and trims) for the period ending at midnight on the first anniversary of the date of first purchase, Glen Dimplex Americas will in its sole discretion either repair or replace such defective product or part without charge. If Glen Dimplex Americas is unable to repair or replace such product or part, or if repair or replacement is not commercially practicable or cannot be timely made, Glen Dimplex Americas may, in lieu of repair or replacement, choose to refund the purchase price for such product or part. This limited warranty entitles the purchaser to on-site or in-home warranty services. Accordingly, Glen Dimplex Americas will be responsible for all labour and transportation costs associated with the repair or replacement of the product or part except as follows: (i) charges may be levied for travel costs incurred to travel to the purchaser’s site where the product is located if the purchaser’s site is beyond 30 miles (48 km) from the closest service depot of Dimplex’s dealer or service agent; and (ii) the purchaser is solely responsible for providing clear access to all serviceable parts of the product.
• For products (other than surrounds (mantels) and trims) for the period commencing at 12:01 a.m. on the day after the first anniversary of the first purchase and ending at midnight on the second anniversary of the date of first purchase, this limited warranty entitles the purchaser to replacement parts only without charge. If Glen Dimplex Americas is unable to replace such part, or if replacement is not commercially practicable or cannot be timely made, Glen Dimplex Americas may, in lieu of replacement, choose to refund the purchase price for such part. The purchaser shall not be entitled to on-site or in-home warranty services. The purchaser shall be responsible for all expenses incurred for the removal of the part and installation of the replacement part including, without limitation, all shipping costs and transportation costs to and from the authorized dealer’s or service agent’s place of business and all labour costs. Such costs shall not be the responsibility of Dimplex.
• For surrounds (mantels) and trims for the period ending at midnight on the first anniversary of the date of first purchase, Glen Dimplex Americas will in its sole discre-tion either repair or replace such defective surrounds (mantels) and trims or part thereof without charge. If Glen Dimplex Americas is unable to repair or replace such product or part, or if repair or replacement is not commercially practicable or cannot be timely made, Glen Dimplex Americas may, in lieu of repair or replacement, choose to refund the purchase price for such product or part. The purchaser shall not be entitled to on-site or in-house services. The purchaser is responsible for all expenses incurred for repair or replacement of such product or part including, without limita-tion, all shipping costs and transportation costs to and from the authorized dealer’s or service agent’s business and all labour costs. Such costs shall not be the responsibility of Dimplex.
• On-site or in-home services not provided under this warranty may be performed at the purchaser’s specific request and expense at Dimplex’s then-current rates for such services.

What Glen Dimplex Americas and its dealers and service agents are also not responsible for:

• IN NO EVENT WILL GLEN DIMPLEX AMERICAS, OR ITS DIRECTORS, OFFICERS, OR AGENTS, BE LIABLE TO THE PURCHASER OR ANY THIRD PARTY. WHETHER IN CONTRACT, IN TORT, OR ON ANY OTHER BASIS, FOR ANY INDIRECT, SPECIAL, PUNITIVE, EXEMPLARY, CONSEQUENTIAL, OR INCIDENTAL LOSS, COST, OR DAMAGE ARISING OUT OF OR IN CONNECTION WITH THE SALE, MAINTENANCE, USE, OR INABILITY TO USE THE PRODUCT, EVEN IF GLEN DIMPLEX AMERICAS OR ITS DIRECTORS, OFFICERS, OR AGENTS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH LOSSES, COSTS OR DAMAGES, OR IF SUCH LOSSES, COSTS, OR DAMAGES ARE FORESEEABLE. IN NO EVENT WILL GLEN DIMPLEX AMERICAS, OR ITS OFFICERS, DIRECTORS, OR AGENTS BE LIABLE FOR ANY DIRECT LOSSES, COSTS, OR DAMAGES THAT EXCEED THE PURCHASE PRICE OF
• THE PRODUCT SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO THE PURCHASER.

How State and Provincial laws apply

• This limited warranty gives you specific legal rights, and you may also have other rights that vary from jurisdiction to jurisdiction.
• The provisions of the United Nations Convention on Contracts for the Sale of Goods shall not apply to this limited warranty or the sale of products covered by this limited warranty.

Technical Support

• Technical and troubleshooting support, as well as a list of replacement parts, can be found at: www.dimplex.com/support
• 1-888-346-7539 | www.dimplex.com
• In keeping with our policy of continuous product improvement, we reserve the right to make changes without notice.
• © 2023 Glen Dimplex Americas
• www.dimplex.com

Documents / Resources

| Revillusion RBF24DLX 24 Inch Built In Firebox [pdf] Owner's Manual
RBF24DLX, RBF24DLX 24 Inch Built In Firebox, 24 Inch Built In Firebox, Built In Firebox, Firebox
---|---

References

• Leave a review | Dimplex
• Electric Fireplace & Heating Solutions | Dimplex
• Heating Product Registration | Dimplex

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>