EDAN INSTRUMENTS ALXC28 Ultrasonic Pocket Doppler User Manual

EDAN INSTRUMENTS ALXC28 Ultrasonic Pocket Doppler

Specification

SDIO x 1 (SDIO 2.0, 25MHz & 50MHz, 1bit & 4bit mode)
I2S/PCM (16bit, 16KHz, 256 kbps)

Hardware Block Diagram

Interface
The module includes various host interfaces to communicate with Bthe Host CPU:

• UART x 1 (Max 4Mbps)
• SDIO x 1 (SDIO 2.0, 25MHz & 50MHz, 1bit & 4bit mode)
• I2S/PCM (16bit, 16KHz, 256 kbps)

Package Info

PIN Description

Feature Highlights

Wi-Fi
The ALXC28 module supports dual-band IEEE802.11 a/b/g/n Wi-Fi technology with improved range and power efficiency.

Security

• WPATM and WPA2TM (Personal) support for powerful encryption and authentication.
• AES in WLAN hardware for faster data encryption and IEEE 802.11i compatibility.

Network Connection Indication
The ALXC28 module provides indications for various network connection states:

• AP connecting
• AP connected
• AP disconnected
• Server connecting
• Server connected
• Server disconnected

Wi-Fi Specification

Wireless Specification – 2.4GHz

11g/n 20MHz: 2412-2462 MHz
11n 40MHz: 2422-2452 MHz
Modulation| DSSS(DBPSK,DQPSK,CCK), OFDM(BPSK,QPSK,16-QAM,64-QAM)
Link Data Rate| 11b: 1,2,5.5L,5.5S,11L,11S
11g: 6,9,12,18,24,36,48,54
11n: MCS 0,1,2,3,4,5,6,7

Wireless Specification – 5GHz

11n 40MHz: 5190-5795 MHz
Modulation| DSSS(DBPSK,DQPSK,CCK), OFDM(BPSK,QPSK,16QAM,64-QAM)
Support Data Rates| 11a: 6,9,12,18,24,36,48,54
11n: MCS 0,1,2,3,4,5,6,7

Rx Sensitivity

2.4GHz Rx Sensitivity

5GHz Rx Sensitivity

FAQ

What are the Wi-Fi standards supported by the ALXC28 module?
The ALXC28 module supports IEEE802.11 a/b/g/n Wi-Fi standards.

What are the available host interfaces for communication with the Host CPU?
The ALXC28 module provides UART, SDIO, and I2S/PCM interfaces for communication with the Host CPU.

What encryption and authentication methods are supported by the ALXC28 module?
The ALXC28 module supports WPATM and

Introduction

Overview
ALXC28 is a small size, low power consumption, dual band IEEE802.11 a/b/g/n WLAN module. It can provide network connection through SDIO, UART, SPI, PCM and other interfaces. The ALXC28 ,highly integrates MAC, Base band, RF, RF front end.

Hardware Block Diagram
ALXC28 wifi module integrates a Wi-Fi BB/MAC/RF SoC and RF front end.

Interface

The module includes various different host interfaces to communicate with Host CPU. Below table lists the basic descriptions of the Wi-Fi SoC and the interfaces.

Table 1 MCU and Interfaces****

Package Info

Table 2

PIN Description

Table 3 Pin Descriptions

Feature Highlights

Wi-Fi

1. Dual–band 2.4 GHz and 5 GHz IEEE 802.11 a/b/g/n.
2. Single–stream IEEE 802.11n support for 20 MHz and 40 MHz channels provides PHY layer rates up to 150 Mbps for typical upper–layer throughput in excess of 90 Mbps.
3. Supports the IEEE 802.11n STBC (space–time block coding) RX and LDPC (low–density parity check) TX options for improved range and power efficiency.
4. Supports IEEE 802.15.2 external coexistence interface to optimize bandwidth utilization with other co–located wireless technologies such as GPS, WiMAX, or UWB
5. Alternative host interface supports HSIC v1.0 (short–distance USB device)

Security

1. WPA™ and WPA2™ (Personal) support for powerful encryption and authentication
2. AES in WLAN hardware for faster data encryption and IEEE 802.11i compatibility
3. Reference WLAN subsystem provides Cisco® Compatible Extensions (CCX, CCX 2.0,

CCX 3.0, CCX 4.0, CCX 5.0)
Reference WLAN subsystem provides Wi–Fi Protected Setup(WPS)

Network Connection Indication
Indications include:

• AP connecting
• AP connected
• AP disconnected
• Server connecting
• Server connected
• Server disconnected

Wi-Fi Specification

Wireless Specification
Table 4 2.4GHz Wireless Specification

Frequency Band

| 11b| 2412-2462 MHz
11g/n 20MHz| 2412-2462 MHz
11n 40MHz| 2422-2452 MHz
Modulation| DSSS(DBPSK,DQPSK,CCK),

OFDM(BPSK,QPSK,16-QAM,64-QAM)

Link Data Rate

| 11b| 1,2,5.5L,5.5S,11L,11S
11g| 6,9,12,18,24,36,48,54
11n| MCS 0,1,2,3,4,5,6,7

Table 5 5GHz Wireless Specification

Frequency

Band

| 11a/n 20MHz| 5180-5825 MHz
11n 40MHz| 5190-5795 MHz
Modulation| DSSS(DBPSK,DQPSK,CCK), OFDM(BPSK,QPSK,16-

QAM,64-QAM)

Support data

rates

| 11a| 6,9,12,18,24,36,48,54
11n| MCS 0,1,2,3,4,5,6,7

**Rx Sensitivity

**

Table 6 2.4GHz Rx Sensitivity

Table 9 5GHz Rx Sensitivity

Federal Communications Commission (FCC) Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Warning : Changes or modifications made to this device not expressly approved by Edan Instruments, Inc. may void the FCC authorization to operate this device.
Note : The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

RF exposure statement:
The transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. This equipment complies with the FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a Minimum distance of 20cm between the radiator and any part of your body.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Country Code selection feature to be disabled for products marketed to the US/Canada. This device is intended only for OEM integrators under the following conditions:

• The antenna must be installed such that 20 cm is maintained between the antenna and users, and
• The transmitter module may not be co-located with any other transmitter or antenna,
• For all products market in US, OEM has to limit the operation channels in CH1 to CH11 for 2.4G band by supplied firmware programming tool. OEM shall not supply any tool or info to the end-user regarding to Regulatory Domain change. (if modular only test Channel 1-11)

As long as the three conditions above are met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed.

Important Note:
In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.

End Product Labeling
The final end product must be labeled in a visible area with the following” Contains FCC ID: SMQXC28EDAN”

Manual Information to the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Integration instructions for host product manufacturers according to KDB 996369 D03 OEM Manual v01r01 2.2 List of applicable FCC rules CFR 47 FCC PART 15 SUBPART C has been investigated. It is applicable to the modular transmitter

Specific operational use conditions
This module is stand-alone modular. If the end product will involve the Multiple simultaneously transmitting condition or different operational conditions for a stand-alone modular transmitter in a host, host manufacturer have to consult with module manufacturer for the installation method in end system.

Limited module procedures
Not applicable

Trace antenna designs
Not applicable

RF exposure considerations
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.

Antennas
This radio transmitter FCC ID: SMQXC28EDAN has been approved by the Federal Communications Commission to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.

LBS-019C

|

FPC antenna

| 2.4GHz – 2.5 GHz

5.15GHz – 5.85 GHz

| 2.85 dBi

3.46 dBi

Label and compliance information
The final end product must be labeled in a visible area with the following” Contains FCC ID: SMQXC28EDAN”.

Information on test modes and additional testing requirements
The host manufacturer is strongly recommended to confirm compliance with FCC requirements for the transmitter when the module is installed in the host.

Additional testing, Part 15 Subpart B disclaimer
The host manufacturer is responsible for compliance of the host system with the module installed with all other applicable requirements for the system such as Part 15 B.

Note EMI Considerations
Host manufacture is recommended to use the D04 Module Integration Guide recommended as “best practice” RF design engineering testing and evaluation in case non-linear interactions generate additional non-compliant limits due to module placement to host components or properties.

How to make changes
This module is stand-alone modular. If the end product will involve Multiple simultaneous transmitting conditions or different operational conditions for a stand-alone modular transmitter in a host, host manufacturer has to consult with the module manufacturer for the installation method in the end system. According to the KDB 996369 D02 Q&A Q12, that a host manufacture only needs to do an evaluation (i.e., no C2PC is required when no emission exceeds the limit of any individual device (including unintentional radiators) as a composite. The host manufacturer must fix any failure.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>