stell SHO 3610 Extendable Articulating Slim TV Mount Instruction Manual
- June 4, 2024
- stell
Table of Contents
SHO 3610 Extendable Articulating Slim TV Mount
Instruction Manual
TOOLS
IMPORTANT SAFETY INFORMATION
- Check the content of the package in parts list on page 2 and make sure that all parts are in order. Do not use damaged or faulty parts.
- Read all instructions before installing the equipment. When you are unsure about any part of the installation process, ask a professional technician for help.
- When tightening the screws, be careful to avoid stripping the thread.
- Do not install on a damp or otherwise damaged wall. The assembly material supplied in the package is designed to be mounted on a wall of bricks and concrete. For installation on walls made of other materials consult a professional.
- Never install or use this product if there are signs of damage.
- The edges of the equipment may cause injury if they are handled improperly.
- This device is not designed for assembly or handling by small children, or persons, who have not been specifically instructed unless supervised by a responsible person to ensure safety during handling or installation. Children should be supervised to ensure that they do not interfere with the equipment.
- Do not allow children to hang on the equipment or otherwise handle it. Otherwise, there is a danger of serious injury. Never insert your fingers or other objects into the mechanism of the equipment. It could cause personal injuries or property damage.
- The product contains small parts that can pose a choking hazard when inhaled or swallowed. Keep these parts out of reach of children!
Note: Specifications and design are subject to change due to improvements without notice.
LIST OF SUPPLIED PARTS
| A Holder | F screw M820 | K spacer (long) |
|---|---|---|
| B Bracket (left and right) | G screw M6x30 | L screw M6.35 x 55 |
| C Allen key | H screw M8x30 | M Plastic anchor M10x45 |
| D screw M5x14 | I Locking washer M6/M8 | N Washer under the screw |
| E Screw.M6x14 | J Spacer (short) | O screw M8x50 |
INSTALLATION
This TVG mount must be securely fastened to a vertical wall. If not solidly installed, it could fall and cause injury or damage.
Installing the mount on the wall of solid brick or concrete wall or panel
Mark the position of the 4 holes on the wall for attaching the body of the
holder (one in each corner of the body of the holder). Use the holder mas A
template (Fig. 1). Using spirit level make sure that the holder is in a
horizontal position. Use a masonry drill (10 mm) to pre-drill holes at least 5
cm deep and insert a plastic anchor into each hole – Check that the plastic
anchor is entirely inserted and even with the wall. (Fig. 2). Attach the body
of the holder to the wall using three screws I and washers GI, as shown in
Fig. 3A.
Leveling the mount
After installing the wall mount, you can later adjust the horizontal position
of the plate to mount the TV.
Loosen the screws on the TV wall mount plate using a Phillips screwdriver and
use spirit level to align the plate in a horizontal position (Fig. 3B).
Tighten the screws after you level the plate (do not use excessive force).
Note: If the TV is not entirely horizontal after installation on the
mount, remove it from the mount (perform the points from pictures 5 and 6 in
reverse order), repeat the process of leveling, and then reinstall the TV set.
Mounting the brackets on the TV set
TV set with a flat rear wall (Fig. 4A)
First, find screws suitable for using to mount the TV set D/F/F: try to screw
them manually in the holes at the back of the TV set. If you feel resistance
stop screwing in immediately! Once you find the screw with the correct threat,
proceed according to the drawing. Insert matching washer on screw I and then
screw it into bracket B and finally in the TV set. Check that the brackets are
attached vertically and parallel.
TV set with a curved rear wall (Fig. 4B)
First, find screws suitable for use on the TV set. (F/G/H): try to screw
them manually in the holes in the back of the TV set. If you feel resistance
stop screwing in immediately! Once you find the screw with the correct
threat, proceed according to the drawing. Attach matching washer on the screw
(if and spacer (I) or their combination as needed and according to the diagram
in picture 4B. Then screw the screw into the bracket B and finally in the
TV set. Check that the brackets are attached vertically and parallel.
Attaching the TV to the bracket and securing with safety screws
Warning: Handling some TV sets requires help of another person. The
manufacturer is not liable for injury or damage to property caused by improper
handling!
First, hook the brackets attached to the TV set (2x ) on the top edge of the
body of holder A , then push the bottom part of the brackets to the bottom
part of the holder and tighten the safety bolts located at the bottom part of
both brackets using Phillips screwdriver (Fig. 6). Set the desired angle
of the screen and using the Allen key (IEI) tighten the screws on the body
turning them by 180°, see fig. 7.
Congratulation, the installation is done. We wish you a pleasant experience
while watching TV mounted on the wall mount.
INSTRUCTIONS AND INFORMATION REGARDING THE DISPOSAL OF USED PACKAGING
Take the used packaging material to municipal waste disposal.
PRODUCT DISPOSAL AFTER END OF LIFE
Dispose of equipment after the end of life in the designated municipal
solid waste place.
This product meets all the basic requirements of EU directives that apply to
it.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>