i-PRO PPRM35AW Parapet Mount Bracket Instruction Manual

: June 14, 2024
: i-PRO

Table of Contents

i-PRO PPRM35AW Parapet Mount Bracket
Specifications
Important Safeguard

i-PRO PPRM35AW Parapet Mount Bracket

i-PRO-PPRM35AW-Parapet-Mount-Bracket-product-image

Specifications

Model: PPRM35AW
Compatible with: i-PRO PS485AW, WV-QSR5xxF1-W, and WV-QAT501-S/W
Manufacturer: i-PRO Americas
Manufacturer’s Address: 8550 Fallbrook Drive, Suite 200, Houston, Texas 77064
Website: https://i-pro.com/us/en/

Important Safeguard

It is important to follow these safeguards to ensure a safe and secure installation of the product

The installation should be performed by a qualified installer.
The installation should comply with local codes.
Select suitable hardware considering the composition of the mounting surface and the weight of the unit.
Regularly inspect the unit and supporting structure to maintain the integrity of the installation.
Failure to comply with these safeguards may result in the unit separating from the support structure, causing damages or injury.

Precautions for Installation

Before starting the installation process, please take note of the following precautions

Ensure you have access to technical support from i-PRO Americas by visiting https://surveillance.i-pro.com/support/ or calling 1-800-513-5417 (M-F 7:00 am–7:00 pm Central Time).
Make sure the installation area is suitable for the product.

Mount Parapet Base to Parapet

Locate the desired location of the Parapet Mount.
Mark the mounting hole locations with a marking device.
Place the Parapet Mount Base to the side.
Drill six pilot holes using the masonry bit included in the hard ware pack.
Use a level to verify that the Parapet Mount Base is level.
Use a hammer to tap six masonry anchors through the Parapet Mount Base mounting holes.
Use a drill or adjustable wrench to tighten the bolt to allo the sleeve to expand inside the pilot hole. (Refer to Figure)

Mount Parapet Arm to Parapet Base:

Place the Parapet Mount Arm into the Parapet Mount Base andalign the holes to the desired angle. (Refer to Figure 2)
Use two M10 bolts to firmly tighten the Base and Arm together and securely fasten using a drill with a socket or an adjustable wrench. (Refer to Figure 3)
If using an Extension Arm, repeat steps 2-1 and 2-2 with two M10 screws.

Pull Cable Necessary to Power Camera:

Pull a Cat5 cable through the Parapet Arm and Base to power the i-Pro camera (Cable not provided).
Verify that the cable is not being pinched or exposed to exterior weather.

FAQ

Q: Where can I get technical support for this product?
A: You can access technical support from i-PRO Americas by visiting https://surveillance.i-pro.com/support/ or calling 1-800-513-5417 (M-F 7:00 am–7:00 pm Central Time).
Q: What should I do if the unit separates from the support structure?
A: Regularly inspect the unit and supporting structure to ensure the integrity of the installation. If the unit separates, it may cause damages or injury. Consult a qualified installer and follow the installation instructions provided.

INSTALLATION INSTRUCTIONS

Before attempting to connect or operate this product, please read instructions completely. Installation and Operation Instructions for the following model

PPRM35AW
Parapet Mount Bracket for use with i-PRO PS485AW, WV-QSR5xxF1-W, and WV- QAT501-S/W

i-PRO-PPRM35AW -Parapet-Mount-Bracket-image01

PPRM35AW

(1) Parapet Mount Base
(1) Parapet Mount Arm w/ 1.5” NPT Threads
(1) Parapet Mount Extension
(1) Hardware Pack

i-PRO-PPRM35AW -Parapet-Mount-Bracket-image02

INCLUDED HARDWARE

(6) Stainless Steel Masonry Anchors
(1) Masonry Drill Bit
(5) M10 Stainless Steel Bolts
(2) End Caps (Mounted)
(4) 3/8” Hex Head Bolts
(4) 3/8” Flat Washer
(4) 3/8” Split Washer

DISTRUBUTED BY

i-PRO Americas
8550 Fallbrook Drive, Suite 200, Houston, Texas 77064 https://i-pro.com/us/en/

IMPORTANT SAFEGUARDS

Read Instructions – All the safety and operating instructions should be read before the unit is operated.
Retain Instructions – The safety and operating instructions should be retained for future reference.
Heed Warnings – All warnings on the unit and in the operating instructions should be adhered to.
Follow Instructions – All operating and user instructions should be followed.
Electrical Connections – Only a qualiﬁed electrician should make electrical connections.
Attachments – Do not use attachments not recommended by the product manufacturer as they may cause hazards.
Cable Runs – All cable runs must be within permissible distance.
Mounting – This unit must be properly and securely mounted to a supporting structure capable of sustaining the weight of the unit.

Accordingly

The installation should be made by a qualiﬁed installer.
The installation should be in compliance with local codes.
Care should be exercised to select suitable hardware to install the unit, taking into account both the composition of the mounting surface and the weight of the unit.

Be sure to periodically examine the unit and the supporting structure to make sure that the integrity of the installation is intact. Failure to comply with the foregoing could result in the unit separating from the support structure and falling, with resultant damages or injury to anyone or anything struck by the falling unit.

PRECAUTIONS FOR INSTALLATION

Do not place this product in the following places

Locations where a chemical agent is used such as a swimming pool
Locations subject to moisture and oil smoke such as a kitchen
Locations that have a specific environment that is subject to an inflammable atmosphere or solvents
Locations where a radiation, an X-ray, a strong radio wave or a strong magnetic field is generated
Locations where corrosive gas is produced, locations where it may be damaged by briny air such as seashores
Locations where the temperature is not within the specified range (–50 °C to +60 °C {-58 °F to 140 °F})
Locations subject to vibrations, such as on vehicles, marine vessels, or above product lines (This product is not designed for on-vehicle use.)
Locations subject to condensation as the result of severe changes in temperature

Tightening the screws and bolts

The screws and bolts must be tightened with an appropriate tightening torque according to the material and strength of the installation area.
Do not use an impact driver. Use of an impact driver may damage the screws or cause tightening excessively.

TECHNICAL SUPPORT

For Technical Support https://surveillance.i-pro.com/support/ 1-800-513-5417 (M-F 7:00 am—7:00 pm Central Time)

Installation area for this product

Make sure that the installation area is strong enough to hold the total weight of the camera and mount assembly before installation.

Tools needed for installation:

Hammer
Drill
12” Level
Adjustable Wrench or 3/8” Hex Head Socket

MOUNT PARAPET BASE TO PARAPET

Locate desired location of Parapet Mount
Mark mounting hole locations with a marking de- vice
Place Parapet Mount Base to the side
Drill (6) pilot holes using masonry bit included in hardware pack.
Use a level to verify Parapet Mount Base in level
Use hammer to tap (6) masonry anchors through Parapet Mount Base mounting holes as shown in Figure 1
Use drill or adjustable wrench to tighten bolt to allow sleeve to expand inside the pilot hole.

Figure 1

MOUNT PARAPET ARM TO PARAPET BASE

Place Parapet Mount Arm into Parapet Mount Base and align holes to desired angle. (Figure 2)
Use (2) M10 bolts to firmly tighten Base and Arm together and securely fasten using drill with socket or adjustable wrench (Figure 3).
For Extension Arm, Repeat steps 2-1 & 2-2 with (2) M10 Screws.

Figure 2

Figure 3

IMPORTANT

Prepare safety tethers and anchor bolts according to the material and strength of the area where the product is to be installed. The pull-out strength of the anchor bolt shall be more than 5 times of the total weight of the in-stalled devices (including the camera body, ceiling mount, anchor bolts, and all other parts.)
i-PRO Sensing Solutions Corporation of America assumes no responsibility for injuries or property damage resulting from failures arising out of improper installation or operation inconsistent with this documentation.

PULL CABLE NECESSARY TO POWER CAMERA

Pull Cat5 cable through the Parapet Arm and Base to power the i-Pro camera (Not Provided)
Verify that cable is not being pinched or exposed to exterior weather.

Mount i-Pro camera to mounting holes of shroud (Not Provided)
Screw Shroud onto end of Parapet Mount Arm (Figure 4)
Attached safety wire provided with camera to triangle gusset attached the Parapet Mount Arm. (Red Circle on Figure 4)