Guarder G10 PRO Fingerprint Front Door Lock Set with Deadbolt User Guide
- June 14, 2024
- Guarder
Table of Contents
Guarder G10 PRO Fingerprint Front Door Lock Set with Deadbolt
What’s in the box
If the lock appears to be damaged or missing parts, please contact customer service email or for further assistance.
Parts List
Installation instructions
- Don’t insert the key to the cylinder when installing the deadbolt
- Battery:
- a. Use new and NON-rechargeable 4*AA batteries for the best use.
- b. Don’t load batteries until the lock is completely installed.
- Adjust latch to insert horizontally.
If you have any problems, don’t hesitate to contact with us through Amazon messaging at the first time.
Simple flowchart of installation
Please refer to the next section if you need a more detailed installation process.
-
Remove existing deadbolt
-
Do not discard old lock hardware until Lock has been successfully installed.
-
Remove the lock from the door, including the old latch.
-
Prepare the door and check dimensions
-
Measure length of the basket
-
Measure diameter of the 2 holes
-
Measure depth of the door frame hole
-
Confirm dimensions
-
Install the latch and strike
-
A. Determine backset and adjust the latch
-
B. Install the latch
-
Install the exterior keypad and the interior assembly
-
Install the exterior keypad step
-
Install exterior parts
-
Keep the deadbolt locked
-
Install interior assembly
-
A. Mounting plate installation tips
-
B. Door lock left / right direction
-
C. Insert IC port
D. Check installation status
PROGRAMMING INSTRUCTION
-
How to use?
-
Unlock the door from outside
-
Indicator light signals and beep
Purple : Acorrect code was entered, one long beep.
Blue: Programming in progress, blue flashing.
Red:
-
An incorrect code was entered, and three short beeps.
-
A programming error, three short beeps.
-
Red blinking and beep after the backlit keypad is off indicates critically low battery.
-
-
Lock the door from outside
Auto lock mode -
Auto lock mode is disabled by default, please refer “Quick set”turn Auto-lock on steps.
-
In auto lock mode, the bolt will extend out automatically in 5-69 seconds after unlocking.
Manual mode
Press “ ” buttons on keypad for 3 seconds.
Lock the door from inside
Deadlock/Privacy Button
Privacy mode is disabled by default
All Entry Codes are disabled except the programming code
Manual mode
Rotate the turn piece to lock position .
Fingerprint register steps
Tips:
Register (add) complete fingerprint area including up, down, left and right edges. Move finger slightly each time when programming to improve accuracy.
Privacy mode
Restore factory settings
Features
- Three ways to access: code, key and fingerprint.
- Low power consumption, 4 AA for 1 Years Battery Life or 50, 000 times unlock. Backlit keypad for use in low light environments.
- 1 Programming Code and 300 user codes ( Included 50 Fingerprints).
- Built-in disguise feature to protect your codes from prying eyes.
- Low battery warning indication.
Setting definitions
| Settings | Default Setting | Definitions |
|---|
Programming Code
|
123456
|
It’s required to change it to a code of your own before programming. In manual mode, Long press the 3 seconds to lock.
4 -9 digits in length must differ from all the User Codes currently.
If you forget the master passcode, you can reset the lock to factory settings, which restores the default programming code.
Auto Lock
|
Disable
|
This feature is optional and can be turned off.
When enabled, the lock will automatically re-lock after 05-69 seconds. After a successful code entry or manual unlock with the key, the lock will automatically re-lock after each unlock to keep your home secure.
Manually Lock
|
Hold 3 seconds
|
If auto-lock is not enabled, you need to do the locking manually.
Silent Mode
|
Disable
| The beep sounds when pressing keypad can be muted, you can still hear low battery alerts.
Privacy Button
|
Disable
|
Privacy mode is disabled by default.
When enabled, activate Privacy mode by pressing the privacy button, for 3 seconds to put the lock in do-not-disturb mode ( All Entry Codes are disabled except the programming code ).
Wrong Code Entry Limit
|
Enabled
| After the wrong code entry limit (5 attempts) has been met, the lock will shutdown (flashing RED) for sixty (60) seconds.
Peek-proof digital keypad
|
Enabled
| Prevent code exposure strangers by entering random digits.
Password Random digits
User Code
|
Disable
|
The lock comes not preset any User Code.
Must be different from the master code and other user codes.
Up to 300 possible User Codes can be stored in the lock at one time.
Warranty
Lifetime Limited Mechanical and Finish Warranty and 1-Year Limited Electronics Warranty Subject to the terms and conditions of the warranty, Guarder extends a lifetime limited mechanical and finish warranty and a one-year limited electronics warranty to the original consumer user ( ″Original User″ ) of our Guader brand product against defects in material and workmanship, as long as the original User occupies the residential premises upon which the product was originally installed, see answers www.WeAreLockSmiths.com for specific warranty details.
Warning
This manufacturer advises that no lock can provide complete security by itself, this lock maybe defeated by forcible or technical means or evaded by entry elsewhere on the property, No lock can substitute for caution, awareness of your environment, and common sense. Builder’s hardware is available in multiple performance grades to suit the application. ln order to enhance security and reduce risk, you should consult a qualified locksmith or other security professional.
Troubleshooting
Installation
| Question | Suggested Action |
|---|
Motor turns but will not extend or retrieve the deadbolt.
| ① Make sure the key is not in the lockset when installing the deadbolt. Refer to Installation Instructions.
② Make sure the backset on the latch is set to the proper length. Refer to Installation Instructions.
③ Please restore to the factory setting and enter the default Master Code to set up the lock.
Why does my lock only work properly when the backup key is in?
Why am I unable to pull the key out in the unlocked position?
| ① You may need to re-install the whole lock.
② Please do not put the backup key in the lock when installed.
③ Please make sure when you start to installed, the lock is in unlocked status.
④ Please make sure the thumb turn is horizontal.
Fail to programming the lock.
| ① Before installation, restore the lock to complete the bolt direction setting.
② Please make sure the lock is installed correctly.
③ Please install fresh batteries and make sure the cable is connected correctly.
Operation
The battery indicator keeps flashing.
| ① The batteries are getting low. Please replace with 4*AA new batteries
for the best performance ( Alkaline batteries, do not recharge batteries ).
---|---
Keypad not responding.
| ① Make sure the batteries are installed properly.
② The batteries are getting low if the battery indicator keeps flashing.
③ Please replace with four new batteries for the best performance ( Alkaline batteries, do not recharge batteries ).
④ Make sure the cable is well-connected to the port, and was not damaged during installation.
⑤ Make sure the lock has been set up and complete the bolt direction determination.
Forgot master code/Default programming code incorrect.| ① Press the reset button on the circuit board to erase all codes.Once the reset is complete, all passcodes will be erased and the programming code will return to the default programming code 123456.
Lockset is not able to unlock/lock by keypad.
| ① Make sure you have entered the correct User Code.
② The battery is low if the battery indicator light keeps flashing. Please replace it with four new batteries.
③ Make sure the cable is firmly connected.
④ Check the cable for any damage that may have occurred during installation.
⑤ Make sure the batteries are properly installed ( Alkaline batteries, do not recharge batteries ).
⑥ Check the strike plate to make sure it is properly aligned and clear so the bolt can freely move in the hole.
Other online update situation scan QR
If you have any installation and set up questions: Please refer to the new
manual or video for specific installation and operation.
24/7 online after-sales email service through Amazon messaging &
Guarderservic@gmail.com You also can call
online phone: +1 323 522 5532 on 9 am to 6 pm PDT.
Quick set
- Recommend you hit the small reset button on the circuit board before assembling the unit to the bracket.
- Test the master code to open the lock and whether the latch will retract
- If the latch does not retract, adjust the direction by step 1. Programming Code=PC User Code=UC
Video Demo QR Code
Documents / Resources
|
Guarder G10 PRO Fingerprint Front Door Lock Set with
Deadbolt
[pdf] User Guide
G10 PRO Fingerprint Front Door Lock Set with Deadbolt, G10 PRO, Fingerprint
Front Door Lock Set with Deadbolt, Door Lock Set with Deadbolt, Lock Set with
Deadbolt
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>