ALLEN HEATH M-DL-GACE ACE Networking Card Instruction Manual
- June 14, 2024
- ALLEN HEATH
Table of Contents
ALLEN HEATH M-DL-GACE ACE Networking Card
Product Information
Specifications
- Product Name: M-DL-GACE
- Audio Networking Option for Allen & Heath dLive I/O Port
- Provides a 128x128ch 96kHz gigaACE point-to-point link
- Uses proprietary Allen & Heath protocol for Audio and Control transport over Ethernet
- Supports cable redundancy and TCP/IP network control
- Requires touring grade CAT5e (or higher specification) cables up to 100m long
- Requires dLive firmware V1.3 or higher
Product Usage Instructions
Fitting the Card
- Switch off the system.
- Remove the 4 screws securing the I/O Port blank panel on the dLive MixRack or Surface.
- Slide the card into the slot and firmly press it into the mating connector.
- Secure the card by tightening the 4 captivated thumb screws.
Setting Clock and Patching Signals
Use the dLive I/O screen to patch signals from or to the I/O Ports. Use the
MixRack / Audio / Audio Sync screen to select the clock source. Set this to
Internal on the master system, or to the relevant I/O Port on all other
networked (clock slave) systems. For more information on dLive setup and
functions, please refer to the dLive Firmware Reference Guide available for
download at www.allen-heath.com.
FAQ
-
Q: What type of cables should I use with M-DL-GACE?
A: Use touring grade CAT5e (or higher specification) cables up to 100m long. -
Q: What firmware version is required for M-DL-GACE?
A: M-DL-GACE requires dLive firmware V1.3 or higher. -
Q: How do I enable the Control Network Bridge?
A: Before enabling the Control Network Bridge, ensure that all devices on the network have unique, compatible IP addresses within the same subnet. -
Q: Where can I find the manufacturer’s warranty conditions?
A: The conditions of the manufacturer’s warranty can be found at www .allen-heath.com/legal. -
Q: Does this product comply with European directives?
A: Yes, this product complies with the European Electromagnetic Compatibility directive 2014/30/EU and the European Low Voltage directive 2014/35/EU.
Introduction
M-DL-GACE is one of several audio networking options that can be fitted to an Allen & Heath dLive I/O Port. It provides a 128x128ch 96kHz gigaACE point- topoint link to another dLive mixing system. gigaACE is a proprietary Allen & Heath protocol for transporting Audio and Control over Ethernet, using standard CAT cables. It allows very low latency, cable redundancy and can tunnel TCP/IP network control over the same connection.
- Use touring grade CAT5e (or higher specification) cables up to 100m long.
- M-DL-GACE requires dLive firmware V1.3 or higher.
Fitting the card
- Switch the system off.
- Remove the 4 screws securing the I/O Port blank panel on the dLive MixRack or Surface.
- Slide the card into the slot and press it firmly into the mating connector.
- Secure the card by tightening the 4 captivated thumb screws.
Setting clock and patching signals
Use the dLive I/O screen to patch signals from or to the I/O Ports. Use the MixRack / Audio / Audio Sync screen to select the clock source. Set this to Internal on the master system, or to the relevant I/O Port on all other networked (clock slave) systems.
- For more information on dLive setup and functions please refer to the dLive Firmware Reference Guide available for download at www.allen-heath.com
Front panel
A limited one year manufacturer’s warranty applies to this product, the
conditions of which can be found at: www.allen-heath.com/legal.
This product complies with the European Electromagnetic Compatibility
directive 2014/30/EU and the European Low Voltage directive 2014/35/EU.
Copyright © 2016 Allen & Heath. All rights reserved.
Allen & Heath Limited, Kernick Industrial Estate, Penryn, Cornwall, TR10 9LU,
UK http://www.allen-heath.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>