SONY NSD-G3000T Onu Integrated High Speed Router User Guide

ONU INTEGRATED HIGH-SPEED ROUTER
Setup Guide
NSD-G3000T

NSD-G3000T Onu Integrated High Speed Router

Owner’s Record
The model and serial numbers are located in the Optical fiber cover.
Record the serial number in the space provided below.
Refer to these numbers whenever you call upon your Sony dealer regarding this product.
Model No. NSD-G3000T
Serial No.

WARNING

Caution – Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure
Factory: Sernet (Suzhou) Technologies Corp.
No.13, Chunhui Road, Suzhou Industrial park, Jiangsu, China

Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 26 cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Country Code selection feature to be disabled for products marketed to the US/ CANADA
Operation of this device is restricted to indoor use only

Safety Information

If any abnormalities occur such as smoke, unusual sound or smell, or deformation of the cabinet, immediately follow the instructions below.

1. Unplug the AC adaptor/power cord.
2. Consult your contractor for inspection and maintenance.

Caution

• Do not let water or foreign objects get in to this unit. If water or foreign objects have gotten into this unit, unplug the AC adaptor/power cord.

• Do not disassemble this unit or make alterations to it. For inspection and maintenance, consult with your contractor.

• If there is a possibility of lightning strike, do not use this unit. If lightning is likely, unplug the AC adaptor/power cord to prevent a fire, electric shock, and malfunction.
  Wireless functions are incorporated into this unit. Note the following when you use this unit. Do not use the wireless functions of this unit when failure occurs. In case of an emergency, immediately unplug the AC adaptor/power cord of this unit.
  – Do not use wireless functions on an airplane.
  – Do not use this unit near automatically-controlled equipment, such as automatic doors o fire alarm:
  – Stop using this unit immediately when there is radio interference on other devices while using this unit.

• Do not touch this unit or AC adaptor while this unit is turned on.
  If your skin remains in contact with it, it may cause low temperature burns.

• Do not use this unit while it is covered with cloth, comforter, etc.

• Insert the connector straight.

• Do not put other objects on this unit.

• If you apply a strong force to this unit, such as by putting a heavy object on it, dropping it, or stepping on it, it may cause injuries or a malfunction.

• Take care not to drop this unit when moving it.

• Do not look into the optical line input jack as the light from the jack may have a bad effect on your eyes.

On placement

• Do not place this unit in any places Where there is excessive oily smoke, steam, moisture, or dust.
• Do not install this unit where it cannot be fixed stably, such as on the ceiling.
• Do not place this unit in an unstable place, such as on a wobbly table or tilted place, as this unit may drop or fall down, which may cause injuries. Use this unit set on a stable place.
• Do not place this unit where water splashes.
• Do not place/store this unit in a place exposed to direct sunlight or close to a heater.
• Do not bring your hand or object close to the ventilation holes.
• Place this unit out of reach from children.

On AC adaptor/power cord

• Do not use an AC adaptor other than the one supplied with this unit.

• The supplied AC adaptor is designed for use with this unit exclusively. It should not be used with other devices.

• Do not damage the power cord. Note the following.
  – Do not get the power cord tucked between this unit and a desk or wall.
  – Do not alter or damage the power cord.
  – Do not put a heavy object on the power cord or pull it forcibly.
  – Do not bring the power cord close to a heating appliance or heat up the power cord.
  – To unplug the power cord from the wall outlet, grasp the plug and pull it.

• Do not touch the AC adaptor/power cord with wet hands.

• Do not wrap the power cord around the AC adaptor. It may cause the cord to break.

• Before cleaning this unit, unplug the AC adaptor/power cord.

• Before moving this unit, unplug the AC adaptor/power cord.

• If this unit is not to be used for a long time, unplug the AC adaptor/ power cord.

Features

This unit is a wireless LAN router which is compatible with the XGS-PON method. By connecting the usable device to the wired or wireless LAN, you can use the high-speed Internet service.
When you join the dedicated loT service, this unit works together with 10T devices and the service. To use an 10T device, you need the dedicated hardware and software which is provided by the service provider. For details, consult with your service provider.

Checking the supplied items
Check that all the following items are included in the package.
If there is any missing item, consult with your service provider.

• NSD-G3000T main unit

« AC adaptor/power cord
Either type is included, (A) or (B).
(A) AC adaptor and power cord

(B) AC adaptor

• Bracket

« Bracket fixing screws (2)

• LAN cable

« SSID label (for preservation)
Contents are identical to those on the SSID label pasted on the bottom of this unit.

« Spare label (for installation personnel)

Setup Guide (this document)

Identifying parts

1. System status indicators
2. WLAN button
3. WPS button
4. RESET button
5. Bracket fixing holes
6. USB 2.0 terminal
7. LAN terminals (compatible with T0GBASE-T) and status indicators
8. LAN terminals (compatible with 1000BASE-T) and status indicators
9. Optical fiber cover
10. DCIN jack
11. Optical line input jack
12. SSID label

System status indicators

address.
MODE| Lights up in green| This unit is working in the XGS-PON mode.
2.4G| Lights up in green| Wireless LAN of 2.4 GHz band is enabled.
5G| Lights up in green| Wireless LAN of 5 GHz band is enabled.
BLUETOOTH| Lights up in green| Bluetooth® is enabled.
SMART HOME| Lights up or flashes in green| The smart home function is working.
WPS| Flashes in red| Pairing is in process.
Lights up in red| Authentication succeeded.

Status indicators of LAN terminals

SGBASE-T
Flashes in orange| Communicating in 100BASE-TX/1000BASE-T/ 2.5GBASE-T/5GBASE-T
Lights up in green| Linked up in 10GBASE-T
Flashes in green| Communicating in 10GBASE-T
TA/LAN 3/LAN 2| Lights up in orange| Linked up in 10BASE-T/ 100BASE-TX
Flashes in orange| Communicating in 10BASE-T/ 100BASE-TX
Lights up in green| Linked up in 1000BASE-T
Flashes in green| Communicating in 1000BASE-T

Attaching the bracket

Attach the supplied bracket to this unit and use this unit in the upright position.

1. With the bracket fixing screws, attach the bracket to the bottom of this unit.

When the bracket is attached correctly, this unit stands as shown below.

Tip
This unit can be installed on the wall using the bracket fixing holes on the side of this unit. For details on wall installation, consult with an installation professional.

Using this unit installed on a wall

Install this unit on a wall as shown i the illustration below using commercially available screws of the following specifications.

Screws for wall mounting (not supplied)

• 5/32in.(M4) x more than 16 mm (5/8in.)
• Minimum screw depth: 12.7 mm (1/21n.)
• 2 pcs

Connecting the optical fiber cable installed in your house directly to

this unit

1. Open the optical fiber cover.

2. Connect the optical fiber cable to the optical line input jack.
   Before connecting, remove the cap attached to the optical line input jack.Be careful not to contaminate the end face of the optical fiber cable. If it gets dirty or scratched, the connection may not be established correctly.
   When the optical fiber cover is detached
   Push in the stoppers of the cover to the hole to attach the cover.

3. Connect the supplied AC adaptor to the DCIN jack.

4. Close the optical fiber cover.
   Run the optical fiber cable and the AC adaptor cord through the cutout and close the cover.

5. Connect the power cord to the AC adaptor and connect the power plug to the wall outlet. Note
   The type of the supplied AC adaptor may be different from the one shown in the illustration.

6. wait for about 2 minutes, and check the system status indicators are as shown below.

Connecting via wireless LAN
Connect your smartphone or computer to this unit. For details on the connection, refer to the operating instructions of your device as well.

1. Set the wireless LAN setting to ON on your smartphone or computer.

2. On the network list screen, select the SSID of this unit (NSD3K-XXXX-X).
   Find the SSID on the SSID label pasted on the bottom of this unit or supplied with this unit.

3. When the password input screen is displayed, enter the 13-digit password (Key (WPA)) of this unit.
   Find the password (Key (WPA)) on the SSID label pasted on the bottom of this unit or supplied with this unit.

Connecting by scanning the two-dimensional code
On a smartphone or tablet, a two-dimensional code can also be used for easy connection.
Scan the two-dimensional code on the label pasted on the bottom of this unit or supplied with this unit, and follow the instructions shown on your screen to establish the connection.

Connecting to a computer via wired LAN

1. Connect the supplied LAN cable to the LAN terminals on this unit and on the computer.

Tip
When you use the LAN 1 terminal, communication is established with the highest communication speed of this unit.
Note
Do not connect a computer to the TA terminal. This terminal is exclusively designed to connect the device that s provided from the service provider. For details, consult with your service provider.

Changing the settings on this unit

To change the various settings on this unit, log in to this unit by the method described below.

1. Connect your smartphone or computer to this unit (page 17).
   For details on the connection, refer to the operating instructions of your device as well.

2. Launch the browser on the connected smartphone or computer.

3. Access the URL shown below, and enter the user name and the password.

Precautions

For the proper and safe usage of this unit, read this section carefully before using this unit.

• Do not connect this unit to a power extension cord that has many other devices connected.
• To reduce the risk of electric shock or other dangers, keep the AC power plug clean and dry.
• This unit s designed for desktop installation or wall mounting. When this unit s installed on the desktop, do not put other objects on this unit. Doing so may damage this unit due to heat buildup or deformation of the exterior. Allow space of 5 cm (2in.) or more around this unit for heat dissipation.
• Do not scratch the exterior of this unit as the coating may come off.
• Do not install this unit near electronic devices which generate strong magnetic fields such as a microwave oven, refrigerator, mobile phone, etc.
• Use this unit within the temperature range described under “Operating environment” of “Specifications.”
• Stop using this unit when the cable is damaged or deteriorated.
• Use a dry cloth to wipe off dust or dirt on this unit. Before cleaning, disconnect all the cables such as the AC adaptor/power cord or LAN cables.
• Do not use cleaning liquid or spray cleaner to clean this unit.
• Using this unit near a TV set or a radio receiver may affect the reception.
• When disposing of the packing material or disused unit, follow the rules of your residential area.

Note on the wireless LAN
Sony cannot assume any responsibility for any damage or loss caused by unauthorized access to or use of the connection destination installed in this unit due to loss or theft of this unit.

On security when using wireless LAN products

• To avoid hacking, access from a malicious third party, or other vulnerabilities, always confirm that a secure wireless LAN is used.
• Security settings are highly important on wireless LAN.
• When security problems happen due to negligence of security measures or due to unavoidable circumstances in using the wireless LAN, Sony cannot assume any responsibility for any damage consequently caused.

Q&A

If you have difficulties in using this unit or this unit stops working, try the following solutions before making inquiries. When this unit still does not function properly, consult with your contractor.

The POWER indicator does not light up even after the AC adaptor is connected.

« Check if all the cables are connected correctly. « Power is not delivered to this unit. Check if the supplied AC adaptor is connected corectly.

You want to reset this unit to the default settings.

Using an object with a fine point, press the RESET button for 5 seconds or more to reset this unit. All the settings will be reset to the default settings.

This unit was restarted at night time.

Software of this unit may be updated to the latest version by the automatic system update function. After this unit s restarted, when the system status indicators are normal, you can use this unit as is.

After this unit is turned on, the ALARM indicator lights up in red.

This unit is malfunctioning. Press the RESET button for 5 seconds or more to reset this unit and check the indicator. If the same situation persists, consult with your contractor for replacement of this unit.

After this unit is turned on, the LINE i ator does not light up.

XGS-PON is not connected. Check if the POWER indicator lights up in green. If the POWER indicator lights up but the LINE indicator does not light up, consult with your contractor to check the connection. The LINE indicator always lights up when the line authentication is successful.

After this unit is turned on, the status indicator of a LAN terminal does not light up.

Internet connection is not available on the comresponding LAN terminal. Check if the device connected to the LAN terminal is tumed on and the LAN cable is connected to the LAN terminal.

Specifications

Dimensions
Approx. 200 mm x 200 mm x 25 mm (77/2in.x7 /sin. x in.)
(hxwxd, main unit only, not including projecting parts)

Mass
Approx. 790 g (13/4 Ib) (main unit only)

Maximum power consumption
30w

Rated current/voltage
DC:12V/2.5A
AC:100V – 240 V
Operating environment
Temperature: 0 °C – 40 °C (32 °F – 104 °F)
Humidity: 0% – 80%

Wired LAN
0GBASE-T (1)
000BASET (3)
Auto-nego, MDI/MDI-X
Wireless LAN
IEEE 802.11ax/ac/a/b/g/n 4×4 MIMO
Interface for loT devices
Bluetooth® Standard Ver.4.2

Design and specifications are subject to change without notice.

Trademarks

• The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Sony Group Corporation and its subsidiaries is under license.
• All other trademarks and registered trademarks are trademarks or registered trademarks of their respective holders.

F-175-100-11(2)
© 2023 Sony Network Communications Inc.
Printed in China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>